Akerstroms SESAM 800 L15 User manual

941211-000 -D1
OPERATING MANUAL
SESAM 800
L15, M6, S6, S3, K3, RXD, RX, RX DIN

2 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
Table of Contents
1 Introduction _________________________________________ 4
2 Scope _____________________________________________ 4
3 TechnicalSpecications_______________________________ 5
4 Description of the System _____________________________ 7
4.1 Receivers ________________________________________________7
4.2 Transmitters ______________________________________________8
5 Description of the Receivers ___________________________ 9
6 Installation of the Receiver____________________________ 12
6.1 Placement of the Receiver __________________________________12
6.2 Antenna Placement________________________________________13
6.3 Connections on the Receiver (All Models) ______________________13
7 Indicators On the Receivers___________________________ 14
7.1 Sesam 800 RX ___________________________________________14
7.2 Sesam 800 RXD Model_____________________________________15
7.3 Sesam 800 RX DIN________________________________________15
8 CongurationOftheReceiver _________________________ 16
8.1 Sesam 800 RX Model ______________________________________16
8.1.1 BasicConguration ______________________________________________ 16
8.1.2 AdvancedConguration ___________________________________________ 17
8.1.3 ErasingAllTransmittersintheReceiver_______________________________ 17
8.2 Sesam 800 RXD Model_____________________________________18
8.2.1 BasicConguration ______________________________________________ 18
8.2.2 AdvancedConguration ___________________________________________ 18
8.2.3 ErasingTransmittersintheReceiverSESAM800RXD __________________ 20
8.2.4 Re-conguringaTransmitterintheReceiver __________________________ 20
8.2.5 PIN Lock in the Receiver __________________________________________ 21

3 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
8.3 Sesam 800 RX DIN _______________________________________23
8.3.1 BasicConguration ______________________________________________ 23
8.3.2 AdvancedConguration ___________________________________________ 23
8.3.3 ErasingAllTransmittersintheReceiverSESAM800RXDIN______________ 24
8.4 HighSecurityTransmissionModeforRXandRXD _______________25
8.5 MemoryCard(OnlyRXD) ___________________________________26
8.5.1 CopyingInformationfromaMemoryCardtoaNewReceiver______________ 26
8.5.2 CopyingInformationfromaReceivertoaMemoryCard __________________ 27
9 Description of the Transmitters ________________________ 28
9.1 Indicators on the Transmitter_________________________________28
10 ReplacingBatteriesintheTransmitters _________________ 30
10.1 ReplacingBatteriesinSesamK3 _____________________________30
10.2 ReplacingBatteriesintheSesam800S3&S6 __________________31
10.3 ReplacingBatteriesinSesam800M6 _________________________32
10.4 ReplacingBatteriesintheSesam800L15 ______________________33
11 Error Codes ________________________________________ 34
11.1 Error Codes, Sesam 800 RXD _______________________________34
11.2 Error Codes, Sesam 800 RX and RX DIN ______________________34
12 Receiver Drill Measure for RX and RXD _________________ 35
12.1 MeasureforRXDIN_______________________________________35

Introduction 4 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
1 Introduction
This manual only covers the installation of the Sesam radio remote door
opening system. The Sesam System is not a complete door opening system:
it provides only the set of outputs that are driven according to the actions
performed by the operator of the transmitter. The way the set of outputs is used
for controlling the doors depends on the specic installation and is outside the
scope of the Sesam.
The complete remote control system, where the controlled object is one part,
has to be tested and approved according to the standards/norms that are ap-
plicable and specic to the controlled object. This is not the responsibility of
Åkerströms Björbo.
2 Scope
The following guide must be used when installing Åkerströms Sesam door
opening system to ensure secure, safe operation. The installation must be car-
ried out by a certied electrician.

Technical Specications 5 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
3 TechnicalSpecications
Tabell 1. TechnicalSpecications,Sesam800
SystemSpecications
Operating frequency: 869,8 MHz
Channel separation: 25 kHz
Power output: < 5 mW
Functional sensitivity: <= -107 dBm BER 10-4
Transmission principle: GMSK, TDMA
Operating Temperature: -25°C - +55°C
Storage Temperature: -40°C - +85°C
SpecicationsRX/RXD
IP- class: IP65
Power Supply, 12-24 V DC versions: 12-24 V AC/DC 150 mA (SELV),
max 4A fuse
Power Supply, 230 V AC versions: 230 V AC 50 Hz 15 mA, max 4A
fuse
Max switching capacity of relays: 2A/250VACwithcosφ=1
Total load on all relays: 4A/250 V AC (not exceeding 2A on
any single relay)
Relay- type SPDT
Fuse on current loop: 2,5AT/250 V AC (IEC 60127-2/V)
Dimensions: 135 x120 x 50 mm
Weight: 450g
Screw size TX20
SpecicationsDIN
Power Supply 12-24 V AC/DC
Max switching capacity of relays: 2A/250VACwithcosφ=1
Fuse on current loop: 2,5AT/250 V AC (IEC 60127-2/V)
Dimensions: 92 x72,5 x 30 mm
Weight: 84g

Technical Specications 6 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
SpecicationsK3
IP- class: IP65
Dimensions: 67x44x13 mm
Weight: 30g
Battery type: 2*CR 2025 Lithium cells
Screw Size PH00
SpecicationsS3
IP- class: IP67
Dimensions: 75 x 46 x 22 mm
Weight: 80g
Battery type: 2*AAA/LR03 Alkaline
Screw Size PH00
SpecicationsS6
IP- class: IP67
Dimensions: 75 x 46 x 22 mm
Weight: 80g
Battery type: 2*AAA/LR03 Alkaline
Screw Size PH00
SpecicationsM6
IP- class: IP67
Dimensions: 100 x 60 x 25 mm
Weight: 130g
Battery type: 2*AA/LR06 Alkaline
Screw Size PH2
SpecicationsL15
IP- class: IP67
Dimensions: 120x75x30
Weight: 200g
Battery type: 2*AA/LR06 Alkaline
Screw Size PH2
There is also a L99 with a display. For
information see the Installation Manual
SESAM L99, 800RX and 800RXD

Description of the System 7 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
4 Description of the System
4.1 Receivers
This document covers three receiver models. RX, RXD and RX DIN.
RX and RXD can be ordered as 230 V AC or 12-24 V AC/DC.
RX DIN only as 12-24 V AC/DC.
Sesam 800 RX:
• 3 Single Pole Double Throw relays.
• Memory capacity: up to 100 transmitters.
Sesam 800 RXD:
• 3 Single Pole Double Throw relays.
• Integrated display and conguration buttons.
• Memory capacity: up to 500 transmitters.
• The receiver can be equipped with an detachable memory card containing a
backup of all conguration parameters.
Sesam 800 RX DIN:
• 3 Single Pole Double Throw relays.
• Memory capacity: up to 100 transmitters.
• Designed for DIN rail

Description of the System 8 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
4.2 Transmitters
This document covers ve transmitter models:
Keyring K3:
• Miniature 3 button transmitter.
• Suitable for controlling 3 non-response time critical functions.
Small S3:
• Small size 3 button transmitter.
• Suitable for controlling 3 functions.
Small S6:
• Small size 6 button transmitter.
• Suitable for controlling 6 functions.
Medium M6:
• Medium size 6 button transmitter.
• Suitable for controlling 6 functions and/or where a larger transmitter is
preferred, for example industrial applications.
Large L15:
• Large 15 button transmitter.
• Suitable for controlling up to 15 functions, for example industrial applica-
tions.

Description of the Receivers 9 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
5 Description of the Receivers
12 3
4 5 67 8 9
R1 R2 R3
4
5
6
71
23
8
9
14
10 11 12 13
Figure1.Sesam 800 RX 230 V AC
model indicators, connections
andjumper.
1.LED1Relay1status
2.LED2Relay2status
3.LED3Relay3status
4.LED4Power
5.LED5Squelch
6.LED6Status
7. LED 7 Learn
8.Powerconnection230VAC
9.JumperJ1HighSecurity
TransmissionModesetting
10.Learn/Erasebutton
11.Connectiontorelay1
12.Connectiontorelay2
13.Connectiontorelay3
14. Antenna connector
12 3
4 5 67 8 9
R1 R2 R3
4
5
6
71
23
8
9
14
10 11 12 13
Figure2.Sesam 800 RX 12-24 V DC
model indicators, connections and
jumper.
1.LED1Relay1status
2.LED2Relay2status
3.LED3Relay3status
4.LED4Power
5.LED5Squelch
6.LED6Status
7. LED 7 Learn
8.Powerconnection12-24VAC/DC
9.JumperJ1HighSecurity
TransmissionModesetting
10.Learn/Erasebutton
11.Connectiontorelay1
12.Connectiontorelay2
13.Connectiontorelay3
14. Antenna connector

Description of the Receivers 10 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
1234
5

Figure3. Sesam 800 RXD
12-24 V DC/AC model
connections
1.Powerconnection
2.Connectiontorelay1
3.Connectiontorelay2
4.Connectiontorelay3
5. Antenna connector
1234
5

Figure4. Sesam 800 RXD 230 V AC model
connections
1.Powerconnection,
2.Connectiontorelay1
3.Connectiontorelay2
4.Connectiontorelay3
5. Antenna connector

Description of the Receivers 11 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
12
3
4
5
Figure5. Sesam800RXDmodeldisplay
andbuttons
1.Learn/Erasebutton
2.Enterbutton
3.Memorypositionupbutton
4.Memorypositiondownbutton
5.Display
Figure6. Sesam 800 RX DIN model
connectionsandbuttons
1.Learn/Erasebutton
2.Powerconnection,
3.Connectiontorelay1
4.Connectiontorelay2
5.Connectiontorelay3
6.LED5Squelch
LED6Status
LED 7 Learn

Installation of the Receiver 12 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
6 Installation of the Receiver
The permanent installation of the receiver must include fuses that protect the
equipment and wiring from over current and short-circuit. In detail the power
supply of the receiver and all relay contacts must be fused.
All fuses are used as disconnecting devices. The fuses shall be easily accessible,
must submit a contact gap of at least 3.0 mm and have to be placed in the line
pole. Note that the fuse must be compatible with IEC 60127-2/V.
After the installation of the equipment, the installed cables must be bound
together in pairs (i.e. by using a cable binder) very close to the terminal blocks.
Note that there might be hazardous voltage in the receiver, therefore only certi-
ed electricians are allowed to open the lid.
6.1 Placement of the Receiver
Select a location that is within the environmental limitations of the receiver and
where it is difcult for unauthorized persons to obtain access to the receiver. If
possible, mount the receiver with the cable glands facing downwards.
For the drilling measure of SESAM RX and RXD see chap-
ter 12.
These receivers are preferably screwed with 4 mm screws
suitable for the surface. Think of the antenna’s size and inu-
ence of any metal objects when choosing placement.
SESAM RX DIN is to be mounted on a DIN rail. On the
back there is a recess that the rail ts in (see 1 in g. 7).
When the recess is pressed against the rail the snap t (see 2
in g. 7) will lock the reciever to the rail automatically. Make
sure that the snap. To remove, withdraw the snap t and lift
the receiver off the rail.
Figure7. DIN receiver, the lock for the rail.

Installation of the Receiver 13 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
6.2 Antenna Placement
Attach the supplied antenna to the antenna connector on the receiver. Note that
the antenna must not be placed near metal objects such as wiring, tinroof, etc.
If an antenna cable is needed, contact Åkerströms Björbo AB.
6.3 Connections on the Receiver (All Models)
The receiver is equipped with connections for relays, power and an external
antenna (see g. 1, g. 2, g. 3, g. 4 and g. 6).
The connections for power connection are, from left to right:
• Line (L)
• Neutral (N)
The connections for each relay are, from left to right:
• Common terminal
• Normally opened (NO)
• Normally closed (NC)
LN
1 2 3 4 5 6 7 8 9
(C) (NO) (NC) (C) (NO) (NC) (C) (NO) (NC)
R1 R2 R3
Figure8. PowerconnectionandRelayconnection

Indicators on the Receivers 14 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
7 Indicators on the Receivers
7.1 Sesam 800 RX
The Sesam 800 RX model has seven LED indicators that is displaying system
information (see g. 1 for positions of the LEDs).
The indications on the LEDs are as follows:
LED 1, Relay 1 status: LED ON indicates that the relay is active.
LED 2, Relay 2 status: LED ON indicates that the relay is active.
LED 3, Relay 3 status: LED ON indicates that the relay is active.
LED 4, Power: Indicates whether the receiver is powered on or not.
LED 5, Squelch: Indicates a detected signal on the operating
frequency band.
LED 6, Status: Indicates that information from a transmitter
associated with the receiver has been received.
LED 7, Learn: Indicates if the transmitter is in Learn Mode.

Indicators on the Receivers 15 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
7.2 Sesam 800 RXD Model
The Sesam 800 RXD model has an integrated display that shows additional
system relevant information (see g. 5).
At activation of a certain function, the transmitter memory position will be
shown in the display window.
If a relay is activated, the following will be shown in the display:
• Left decimal point: Relay 1 activated.
• Both decimal points: Relay 2 activated.
• Right decimal point: Relay 3 activated.
At start up, the display will show system information in the following order:
• System version.
• “  ” if a memory card is installed.
• Number of used memory position.
7.3 Sesam 800 RX DIN
The Sesam 800 RX DIN model has three LED indicators that is displaying
system information (see g. 6 for positions of the LEDs).
The indications on the LEDs are as follows:
LED 5, Squelch: Indicates a detected signal on the operating frequency
band.
LED 6, Status: Indicates that information from a transmitter associated
with the receiver has been received.
LED 7, Learn: Indicates if the transmitter is in Learn Mode.

Conguration of the Receiver 16 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
8 CongurationoftheReceiver
8.1 Sesam 800 RX Model
8.1.1 BasicConguration
1. Open the lid on the receiver (6 TX20 screws).
2. Press the Learn/Erase button until LED 7 is ON. The Learn Mode
will be active for 10 seconds (as long as LED 7 is ON).
a. Transmitters Keyring K3 and Small S3: Press button 1 on the transmit-
ter if buttons 1-3 shall be used for activating the relays in the receiver.
b. Transmitter Small S6 and Medium M6:
Press button 1 on the transmitter if button 1-3 shall be used for activat-
ing the relays in the receiver.
Press button 4 on the transmitter if button 4-6 shall be used for activat-
ing the relays in the receiver.
c. Transmitter Large L15: Press the button on the transmitter that shall be
used for activating relay 1 in the receiver.
3. LED 7 on the receiver ashes 3 times if the Learn procedure is successful.
4. Mount the lid on the receiver. Tighten the screws with TX20, torque 2,0
Nm.

Conguration of the Receiver 17 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
8.1.2 AdvancedConguration
This conguration allows the user to determine which button activates a specic
relay.
1. Open the lid on the receiver (6 TX20 screws).
2. Press the Learn/Erase button until LED 7 is ON. The Learn Mode will be
active for 10 seconds.
a. Press the Learn/Erase button once in order to select relay one (the status
LED will ash once).
b. Press the Learn/Erase button twice in order to activate relay two (the
status LED will ash twice).
c. Press the Learn/Erase button three times in order to activate relay three
(the status LED will ash three times).
3. Press the button that shall be used for activating the selected relay in the
receiver. If the conguration is accepted by the receiver, LED 7 ashes 3
times.
4. Mount the lid on the receiver. Tighten the screws with TX20, torque 2,0
Nm.
8.1.3 ErasingAllTransmittersintheReceiver
1. Open the lid on the receiver (6 TX20 screws).
2. Press the Learn/Erase button until LED 7 is ON. The Learn Mode will be
active for 10 seconds.
3. Press the Learn/Erase button for 5 seconds (until LED 7 is OFF). All trans-
mitters are now erased from the receiver memory.
4. Mount the lid on the receiver. Tighten the screws with with TX20, torque
2,0 Nm.

Conguration of the Receiver 18 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
8.2 Sesam 800 RXD Model
8.2.1 BasicConguration
1. Press the Learn/Erase button.
The display window shall show “L  n” followed by the memory position
that the transmitter will be stored in.
The right decimal on the display ashes as long as the Learn mode is active
(10 seconds).
a. Transmitters Keyring K3 and Small S3:
Press button 1 on the transmitter if buttons 1-3 shall be used for activat-
ing the relays in the receiver.
b. Transmitter Small S6 and Medium M6:
Press button 1 on the transmitter if button 1-3 shall be used for activat-
ing the relays in the receiver.
Press button 4 on the transmitter if button 4-6 shall be used for activat-
ing the relays in the receiver.
c. Transmitter Large L15:
Press the button on the transmitter that shall be used for activating relay
1 in the receiver.
2. The display shows “A  ” if the learn process is successful and the
receiver will return to normal operating mode automatically.
8.2.2 AdvancedConguration
This conguration allows the user to choose at what memory position a certain
transmitter shall be stored in and to determine which button activates a specic
relay.
Adding a transmitter in a certain memory position
1. Press the Learn/Erase button.
The display window shall show “L  n” followed by the memory position
that the transmitter will be stored in.
The right decimal on the display ashes as long as the Learn mode is active
(10 seconds)

Conguration of the Receiver 19 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
2. To select what memory position to use (memory positions can be 1-500)
press the Memory Position UP or Memory Position DOWN buttons (see
g. 5). The ashing left decimal on the display indicates whether the cho-
sen memory position is already used.
a. Transmitters Keyring K3 and Small S3:
Press button 1 on the transmitter if buttons 1-3 shall be used for activat-
ing the relays in the receiver.
b. Transmitter Small S6 and Medium M6:
Press button 1 on the transmitter if button 1-3 shall be used for activat-
ing the relays in the receiver. Press button 4 on the transmitter if button
4-6 shall be used for activating the relays in the receiver.
c. Transmitter Large L15:
Press the button on the transmitter that shall be used for activating relay
1 in the receiver.
3. The display will show “A  ” and will return to normal operating mode.
Changing the transmitter push button number and receiver relay relation-
ship
1. Press the Learn/Erase button.
2. Press the Enter button to choose relay, repeated pressure switches relay.
The display shows what relay that will be used. The format is “R=X”
where X is the relay used.
3. Press the button on the transmitter that will activate the relay.
4. The display will show “A  ” and will return to normal operating mode.

Conguration of the Receiver 20 (36)
Sesam 800 Operating Manual Document-ID: 941211-000
Version: D1 Author: SH
8.2.3 ErasingTransmittersintheReceiverSESAM800RXD
Erasing individual transmitters
1. Press the Learn/Erase button.
The display shows “L  n” followed by the memory position that will be
erased. This mode will be active for 10 seconds.
2. Change what memory position to delete (1 to 500) by using “+” and “-”
buttons.
The left decimal in the display window indicates whether the memory posi-
tion is in use or not (note that two decimals are shown in the display).
3. Press the Learn/Erase button to remove the selected memory position.
4. The display will show “D E L” and return to normal operation.
Erasing all transmitters
1. Press the Learn/Erase button.
The display shows “L  n” followed by the memory position that will be
erased. This mode will be active for 10 seconds.
2. Press and hold the Learn/Erase button for 5 seconds to erase all memory
positions.
3. The display will show “D E L” “A L L” and return to normal operation.
All transmitters are now erased from the receiver memory and, if connected, the
memory card.
8.2.4 Re-conguringaTransmitterintheReceiver
If the user attempts to program a transmitter that is already programmed in the
receiver, the display will show “E   1” followed by the original memory
position on the display.
Erase the original memory position before proceeding with the conguration.