Alberici billyone User manual

GUIDA RAPIDA BILLYONE CCTALK - PULSE
Alberici takes all possible measures to grant
The quality of this product.
Improper installation and wrong use can reduce
its performance and its working life.
Technical specs:
Press the yellow button (T) to remove the faceplate.
Press the slide-button (P) to open the upper cover.
A. Sensors B. Rollers C. Rolls
Wipe the sensor surface off by a lint-free cloth or by a cotton-bud,
eventually moisted with isopropyl alcohol to c lean parts A, B and C.
Mounting cut-out (max thickness = 7mm):
Or even a simple square cut will do:
T
P
Dip-Switch row
P
105 mm
43 mm
Dip
-
Switch
row
10p
Connector
10p connector
BILLYONE banknote validator
Quick guide
Rev. 1.05

GUIDA RAPIDA BILLYONE CCTALK - PULSE
Please pay attention: after any change in the DS settings, power must be turned off and then on again, so that the validator can detect the set operation mode.
CCTALK COMMANDS
CcTalk supported specifications list
1. cctalk Generic Specification Issue 3.2
2. cctalk Expansion for Bill Validators Issue2.1
CcTalk supported commands list
1. Core Commands
Header 192 - Request build code
Header 244 - Request product code
Header 245 - Request equipment category id
Header 246 - Request manufacturer id
Header 254 - Simple poll
2. Core Plus Commands
Header 001 - Reset device
Header 004 - Request comms revision
Header 241 - Request software revision
Header 242 - Request serial number
3. Bill Validator Commands
Header 145 - Request currency revision
Header 152 - Request bill operating mode
Header 153 - Modify bill operating mode
Header 154 - Route bill
Header 156 - Request country scaling factor
Header 157 - Request bill id
Header 159 - Read buffered bill events
Header 197 - Calculate ROM checksum
Header 213 - Request Option flags
Header 216 - Request data storage availability
Header 227 - Request inhibit status
Header 228 - Modify master inhibit status
Header 230 - Request inhibit status
Header 231 - Modify inhibit status
Header 247 - Request variable set
Luminescent Signals AF Modes (Anti-fraud)
nr red
flashes
Description
1 Validator is open
2 Jammed banknote
3 Fraud attempted
5 Adjust optics
7 -
9 Low power supply
11 Check encoder+motor efficiency
12 -
14 ROM error
®
P ROGETTAZIONE E PRODUZIONE DI SISTEMI DI PAGAMENTO , ACCESSORI PER VIDEOGAMES E MACCHINE VENDING
D ESIGN AND MANUFACTURE OF PAYMENT SYSTEMS , ACCESSORIES FOR VIDEOGAMES AND VENDING MACHINES
Via
Ca’ Bianca 421
40024 Castel San Pietro Terme (BO) - ITALY
Tel. + 39 051 944 300
Fax. + 39 051 944 594
http://www.alberici.net
[email protected]
SW Nr DIP-SWITCH FUNCTION
SW 1 OFF Normal acceptance - High security ON Widened acceptance – Low security
SW 2 OFF Anti-fraud with warning enabled, (see ** in Table
AF Modes below), 5 attempts + temporary inhibit ON Anti-fraud with warning disabled, (see * in Table AF Modes below)
SW 3
and
SW 4
SW 3 SW 4 Set up of slot luminescence
OFF OFF Changing colours
ON OFF Green
OFF ON Blue
ON ON White
SW 5
Serial modes (Dip-Sw8=OFF) Pulse Mode (Dip-Sw8=ON)
SW 5 Function SW 5 Pulse width
OFF n.d. OFF 100msec./100msec.
ON n.d. ON 200msec./200msec.
SW 6
and
SW 7
Serial modes (Dip-Sw8=OFF) Pulse Mode (Dip-Sw8=ON)
SW 6 SW 7 Operating mode (protocol) SW 6 SW 7 Pulse number
OFF OFF ccTalk OFF OFF 5 euro = 1 pulse
ON OFF n.d. ON OFF 5 Euro = 5 pulses
OFF ON n.d. OFF ON 10 Euro = 5 pulses (5 € disabled) [v. 2.02 on]
ON ON n.d. ON ON 5 Euro = 10 pulses [v. 2.02 on]
SW 8 OFF Serial mode (Select by Dip-switch 6 + 7: ex. ccTalk: SW6=OFF e SW7=OFF)
ON Pulse mode
Pin Signal Function Pin Signal Function
1 CCT CCT Data (active low) 6 NC Not connected
2 NC Not connected 7 Vcc + 12 / 24 Vdc (Power supply)
3 NC Not connected 8 Vss GND (Power supply)
4 NC GND 9 NC Not connected
5 NC Not connected 10 Vcc + 12 / 24 Vdc (Power supply)
Pin Signal Function Pin Signal Function
1 INH+ Inhibit (GND = enabled) 6 NC Not connected
2 NC Not connected 7 Vcc + 12 / 24 Vdc (Power supply)
3 NC Not connected 8 Vss GND (Power supply)
4 NC GND 9 VEND Credit out (active low)
5 NC Not connected 10 Vcc + 12 / 24 Vdc (Power supply)
(*) Dip-Switch SW2 ON
After fraud attempts
, the validator returns the banknote. No signal given.
(**) Dip-Switch SW2 OFF
Attempt Validator reaction Do as described below
1° Remains in service -
2° Remains in service -
3°
>
error (3 red flashes) Reset (switch off then on)
… 4° … > error (3 red flashes) Reset (switch off then on)
After the 5th fraud attempt (3 yellow flashes), it is necessary to wait for automatic
restore of service. Take care not to switch the device off.