WARNING:
NOTE:
Accurate door preparation is essential for the functioning of this lock.
DOOR PREPARATION
A
When drilling through the door, drill from both sides to avoid
damaging the door.
B
Please follow the enclosed template and instructions carefully.
Drill a 35mm hole through the door for privacy sets and a
C
20mm hole for passage sets.
Drill (2) 5mm holes through the door where through bolt
Drill a 24mm hole x 85mm deep into the front edge of the
door.
Mark centre for either passage or privacy set.A
B
C
Fold template at correct height (suggested height for centreline is
4
4
4
4
4
DRILL HOLES
Mark centre of door thickness on horizontal centreline.
3
3
3
3
3
1
1
1
1
1
2
2
2
2
2
P R E P AR E J AMB & INS T ALL S T R IK E
A
B
C
Insert latch into hole. Trace around face plate.
Fasten latch to door so bevelled edge of latchbolt faces
jamb.
5
5
5
5
5
6
6
6
6
6
A
B
INSTALL FURNITURE
Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
Drill (2) 20mm holes x 15mm deep, 8mm above and below
height centreline.
Use strike plate as pattern for cutout. Chisel out and
install strike.
(Privacy Set Illustrated)
(Universal Strike Illustrated)
Insert spindles into furniture, as illustrated.
(When through bolt xing method is being used, cut bolts to appropriate length.)
WARNING:
NOTE:
Accurate door preparation is essential for the functioning of this lock.
DOOR PREPARATION
A
When drilling through the door, drill from both sides to avoid
damaging the door.
B
Please follow the enclosed template and instructions carefully.
Drill a 35mm hole through the door for privacy sets and a
C
20mm hole for passage sets.
Drill (2) 5mm holes through the door where through bolt
Drill a 24mm hole x 85mm deep into the front edge of the
door.
Mark centre for either passage or privacy set.A
B
C
Fold template at correct height (suggested height for centreline is
4
4
4
4
4
DRILL HOLES
Mark centre of door thickness on horizontal centreline.
3
3
3
3
3
1
1
1
1
12
2
2
2
2
P R E P AR E J AMB & INS T ALL S T R IK EINS T ALL LATC H
A
B
C
A
B
C
Insert latch into hole. Trace around face plate.
Fasten latch to door so bevelled edge of latchbolt faces
jamb.
5
5
5
5
5
6
6
6
6
6
REMOVE ROSE CAPS
A
B
INSTALL FURNITURE
Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
Drill (2) 20mm holes x 15mm deep, 8mm above and below
height centreline.
Use strike plate as pattern for cutout. Chisel out and
install strike.
(Privacy Set Illustrated)
(Universal Strike Illustrated)
Insert spindles into furniture, as illustrated.
(When through bolt xing method is being used, cut bolts to appropriate length.)
WARNING:
NOTE:
Accurate door preparation is essential for the functioning of this lock.
DOOR PREPARATION
A
When drilling through the door, drill from both sides to avoid
damaging the door.
B
Please follow the enclosed template and instructions carefully.
Drill a 35mm hole through the door for privacy sets and a
C
20mm hole for passage sets.
Drill (2) 5mm holes through the door where through bolt
Drill a 24mm hole x 85mm deep into the front edge of the
door.
Mark centre for either passage or privacy set.A
B
C
Fold template at correct height (suggested height for centreline is
Mark centre of door thickness on horizontal centreline.
3
3
3
3
3
1
1
1
1
1
2
2
2
2
2
P R E P AR E J AMB & INS T ALL S T R IK E
INS T ALL LAT C H
A
B
C
Insert latch into hole. Trace around face plate.
Fasten latch to door so bevelled edge of latchbolt faces
jamb.
5
5
5
5
5
6
6
6
6
REMOVE ROSE CAPS
A
B
INSTALL FURNITURE
Mark vertical line and height centreline on jamb, exactly
opposite centre of latch.
Drill (2) 20mm holes x 15mm deep, 8mm above and below
height centreline.
Use strike plate as pattern for cutout. Chisel out and
install strike.
(Privacy Set Illustrated)
(Universal Strike Illustrated)
Insert spindles into furniture, as illustrated.
(When through bolt xing method is being used, cut bolts to appropriate length.)
7000/9000 and Medio Series
Installation Instructions
6000/8000 and Series
Installation Instructions
Legge schlage Installation Instructions.indd 1 13/11/2013 9:49:40 a.m.
