Allen-Bradley ArmorBlock 1732E-8IOLM12R Manual

Wiring Diagrams
ArmorBlock IO-Link Master Module
Catalog Numbers 1732E-8IOLM12R
Parts List
Your package contains one 1732E ArmorBlock™ module, a set of label markers,
and these pinout guide wiring instructions.
For complete installation instructions, refer to the Module Publication Number
table and visit http://www.rockwellautomation.com/literature/.
I/O Connectors
Micro-style 5-Pin I/O Female Connector
Module Publication Number
Module Publication Number
ArmorBlock I/O 8 Channel IO-Link Master Module
Installation Instructions 1732E-IN001
ATTENTION: This equipment is intended for use in a Pollution Degree 2
industrial environment
ATTENTION: Two sets of mounting holes are used to mount the module
directly to a panel or machine. Mounting holes accommodate #8 (M4) pan
head screws. The torque specification is 0.68 Nm (6 lb-in.).
3
4
1
2
5
45762
(View into connector)
Pin 1 Sensor source voltage
Pin 2 IO-Link, Input/output B
Pin 3 Return
Pin 4 IO-Link, Input/output A
Pin 5 PE

2ArmorBlock IO-Link Master Module
Publication 1732E-WD008A-EN-P - July 2016
EtherNet/IP Connector
D-Code Micro Network Female Connector
Auxiliary Power Connector
Auxiliary Power Micro-style 4-Pin Receptacles
IMPORTANT
The maximum current that any pin on the power connectors can carry is 4 A.
ATTENTION: To comply with the CE Low Voltage Directive (LVD), this
equipment and all connected I/O must be powered from a source compliant
with the following:
Safety Extra Low Voltage (SELV) or Protected Extra Low Voltage (PELV).
ATTENTION: To comply with UL restrictions, this equipment must be
powered from a source compliant with the following: Limited Voltage.
Safety Extra Low Voltage (SELV) or Protected Extra Low Voltage (PELV).
ATTENTION: This equipment is considered Group 1, Class A industrial
equipment according to IEC/CISPR 11. Without appropriate precautions,
there may be difficulties with electromagnetic compatibility in residential
and other environments due to conducted and radiated disturbance.
(View into connector 1)
Pin 1 M12_Tx+
Pin 2 M12_Rx+
Pin 3 M12_Tx-
Pin 4 M12_Rx-
Pin 5 Connector shell
shield GND
4
2
31
5
44808
(View into connector 2)
Pin 1 M12_Rx+
Pin 2 M12_Tx+
Pin 3 M12_Rx-
Pin 4 M12_Tx-
Pin 5 Connector shell
shield GND
1
4
3
2
Male Input Female Output
(View into receptacle)
Pin 1 Auxiliary power+
Pin 2 Module/sensor power+
Pin 3 Module/sensor power-
Pin 4 Auxiliary power-
45764
3
4
1
2
45763

ArmorBlock IO-Link Master Module 3
Publication 1732E-WD008A-EN-P - July 2016
Specifications
Environmental Specifications
Attribute Value
Temperature, operating IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20…60 °C (-4…140 °F)
Temperature, ambient
rating (UL) 60 °C (140 °F)
Voltage, operating 20…28.8V DC
Output current, per port 500 mA
Output current, per channel 250 mA
Enclosure type rating Meets IP65/66/67/69K
Certifications
Certification (when
product is marked)(1)
(1) See the Product Certification link at http://www.rockwellautomation.com/products/certification/ for
Declaration of Conformity, Certificates, and other certification details.
Value
c-UR-us UL Listed Industrial Control Equipment, certified for US and
Canada. See UL File E322657.
CE EMC Directive 2014/30/EU Directive, compliant with:
EN 61326-1; Meas./Control/Lab., Industrial Requirements
EN 61000-6-2; Industrial Immunity
EN 61000-6-4; Industrial Emissions
EN 61131-2; Programmable Controllers (Clause 8, Zone A & B)
RCM Australian Radiocommunications Act, compliant with:
AS/NZS CISPR 11; Industrial Emissions
KC Korean Registration of Broadcasting and Communications
Equipment, compliant with:
Article 58-2 of Radio Waves Act, Clause 3
EtherNet/IP ODVA conformance tested to Ethernet/IP specifications.

Rockwell Automation Support
Rockwell Automation provides technical information on the Web to assist you in using
its products. At http://www.rockwellautomation.com/support, you can find technical
manuals, a knowledge base of FAQs, technical and application notes, sample code and
links to software service packs, and a MySupport feature that you can customize to
make the best use of these tools.
For an additional level of technical phone support for installation, configuration, and
troubleshooting, we offer TechConnect support programs. For more information,
contact your local distributor or Rockwell Automation representative, or visit
http://www.rockwellautomation.com/support.
Installation Assistance
If you experience a problem within the first 24 hours of installation, please review the
information that's contained in this manual. You can also contact a special Customer
Support number for initial help in getting your product up and running.
New Product Satisfaction Return
Rockwell Automation tests all of its products to ensure that they are fully operational
when shipped from the manufacturing facility. However, if your product is not
functioning and needs to be returned, follow these procedures.
Rockwell Automation maintains current product environmental information on its website at
http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page
Allen-Bradley, Rockwell Automation, ArmorBlock and TechConnect are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
United States 1.440.646.3434
Monday – Friday, 8 a.m. – 5 p.m. EST
Outside United States Please contact your local Rockwell Automation representative for any
technical support issues.
United States Contact your distributor. You must provide a Customer Support case number
(see phone number above to obtain one) to your distributor in order to
complete the return process.
Outside United States Please contact your local Rockwell Automation representative for the return
procedure.
Publication 1732E-WD008A-EN-P - July 2016 PN-408705
Copyright © 2016 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.