Allen-Bradley Studio 5000 Logix Emulate Owner's manual

Programming Manual
Logix 5000 Controllers Nonvolatile Memory
Card
1756 ControlLogix, 1756 GuardLogix, 1769 CompactLogix,
1769 Compact GuardLogix, 1789 SoftLogix, 5069 CompactLogix,
5069 CompactGuardLogix, Studio 5000 Logix Emulate

Important user information
Read this document and the documents listed in the additional resources section about installation, configuration, and operation of this
equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and
wiring instructions in addition to requirements of all applicable codes, laws, and standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried
out by suitably trained personnel in accordance with applicable code of practice. If this equipment is used in a manner not specified by the
manufacturer, the protection provided by the equipment may be impaired.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or
application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements
associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the
examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described
in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING: Identifies information about practices or circumstances that can cause an explosion in
a hazardous environment, which may lead to personal injury or death, property damage, or
economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to personal
injury or death, property damage, or economic loss. Attentions help you identify a hazard, avoid a
hazard, and recognize the consequence
Important: Identifies information that is critical for successful application and understanding of the product.
Labels may also be on or inside the equipment to provide specific precautions.
SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to
alert people that dangerous voltage may be present.
BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert
people that surfaces may reach dangerous temperatures.
ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control
center, to alert people to potential Arc Flash. Arc Flash will cause severe injury or death. Wear
proper Personal Protective Equipment (PPE). Follow ALL Regulatory requirements for safe work
practices and for Personal Protective Equipment (PPE).
Allen-Bradley, Rockwell Software, Rockwell Automation, and TechConnect are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Automation Publication 1756-PM017H-EN-P - February 2018 3
Summary of Changes
This manual includes new and updated information. Use these reference
tables to locate changed information.
Grammatical and editorial style changes are not included in this summary.
Global changes
This table identifies changes that apply to all information about a subject in
the manual and the reason for the change. For example, the addition of new
supported hardware, a software design change, or additional reference
material would result in changes to all of the topics that deal with that
subject.
Subject Reason
Updated screen shots. The Studio 5000 Logix Designer® interface has
been modified in versions 31 and later.
New or enhanced features
This table contains a list of topics changed in this version, the reason for the
change, and a link to the topic that contains the changed information.
Topic Name Reason
Cover Added 5069 Compact GuardLogix to the list of
supported controllers.
Controllers with Memory Card
Options on page 12 Updated the list of controller types.

Rockwell Automation Publication 1756-PM017H-EN-P - February 2018 5
Table of contents
Studio 5000 environment................................................................................ 7
Additional resources....................................................................................... 7
Legal notices................................................................................................... 8
Chapter 1
Introduction................................................................................................... 11
Controllers with Memory Card Options....................................................... 12
Prevent a Major Fault During a Load..................................................... 13
Read/Write Card Data............................................................................ 14
CompactFlash Card Formatting............................................................. 14
Secure Digital Card Formatting ............................................................. 15
Perform Firmware Updates.................................................................... 15
When to Load an Image ......................................................................... 16
Store a Project............................................................................................... 18
Load a Project............................................................................................... 21
Check for a Load .......................................................................................... 24
Clear a Memory Card ................................................................................... 25
Change the Load Image Option ............................................................. 26
Clear the Project from the Controller..................................................... 26
Store the Empty Image........................................................................... 27
Chapter 2
Introduction................................................................................................... 29
Change Which Project Loads ....................................................................... 29
Change the Load Parameters ........................................................................ 30
Other Uses for a Memory Card..................................................................... 31
Preface
Store and Load a
Project By Using a
Memory Card
Use a Memory Card
Reader
Index

Rockwell Automation Publication 1756-PM017H-EN-P - February 2018 7
Preface
This manual shows you how to access and use a memory card in Logix5000
controllers.This manual is one of a set of related manuals that show common
procedures for programming and operating Logix 5000™ controllers.
For a complete list of common procedures manuals, refer to the Logix 5000
Controllers Common Procedures Programming Manual, publication 1756-
PM001.
•The term Logix 5000 controller refers to any controller that is based on
the Logix 5000 operating system.
The Studio 5000 Automation Engineering & Design Environment®
combines engineering and design elements into a common environment. The
first element is the Studio 5000 Logix Designer® application. The Logix
Designer application is the rebranding of RSLogix 5000® software and will
continue to be the product to program Logix 5000™ controllers for discrete,
process, batch, motion, safety, and drive-based solutions.
The Studio 5000® environment is the foundation for the future of
Rockwell Automation® engineering design tools and capabilities. The Studio
5000 environment is the one place for design engineers to develop all
elements of their control system.
These documents contain additional information concerning related
Rockwell Automation products.
Resource Description
Industrial Automation Wiring and
Grounding Guidelines, publication 1770-
4.1
Provides general guidelines for
installing a Rockwell Automation
industrial system.
Product Certifications webpage,
available at
http://ab.rockwellautomation.com
Provides declarations of conformity,
certificates, and other certification
details.
Studio 5000
environment
Additional
resources

Preface
8Rockwell Automation Publication 1756-PM017H-EN-P - February 2018
You can view or download publications at
http://www.rockwellautomation.com/literature. To order paper copies of
technical documentation, contact your local Rockwell Automation distributor
or sales representative.
Copyright notice
Copyright © 2018 Rockwell Automation Technologies, Inc. All Rights
Reserved. Printed in USA.
This document and any accompanying Rockwell Software products are
copyrighted by Rockwell Automation Technologies, Inc. Any reproduction
and/or distribution without prior written consent from Rockwell Automation
Technologies, Inc. is strictly prohibited. Please refer to the license agreement
for details.
End User License Agreement (EULA)
You can view the Rockwell Automation End-User License Agreement
("EULA") by opening the License.rtf file located in your product's install
folder on your hard drive.
Other Licenses
The software included in this product contains copyrighted software that is
licensed under one or more open source licenses. Copies of those licenses are
included with the software. Corresponding Source code for open source
packages included in this product can be located at their respective web
site(s).
You may alternately obtain complete Corresponding Source code by
contacting Rockwell Automation via our Contact form on the Rockwell
Automation website: http://www.rockwellautomation.com/global/about-
us/contact/contact.page.
Please include "Open Source" as part of the request text.
The following open source software is used in this product:
Software Copyright License Name License Text
AngularJS Copyright 2010-2017 Google, Inc. MIT License AngularJS 1.5.9 License
Bootstrap Copyright 2011-2017 Twitter, Inc.
Copyright 2011-2017 The Bootstrap Authors MIT License Bootstrap 3.3.7 License
jQuery Copyright 2005, 2014 JS Foundation and
other contributors MIT License jQuery 2.1.1 License
OpenSans Copyright 2017 Google, Inc. Apache License,
Version 2.0 OpenSans License
Legal notices

Preface
Rockwell Automation Publication 1756-PM017H-EN-P - February 2018 9
Trademark Notices
Allen-Bradley, ControlBus, ControlFLASH, Compact GuardLogix, Compact
I/O, ControlLogix, CompactLogix, DCM, DH+, Data Highway Plus,
DriveLogix, DPI, DriveTools, Explorer, FactoryTalk, FactoryTalk
Administration Console, FactoryTalk Alarms and Events, FactoryTalk Batch,
FactoryTalk Directory, FactoryTalk Security, FactoryTalk Services Platform,
FactoryTalk View, FactoryTalk View SE, FLEX Ex, FlexLogix, FLEX I/O,
Guard I/O, High Performance Drive, Integrated Architecture, Kinetix,
Logix5000, Logix 5000, Logix5550, MicroLogix, DeviceNet, EtherNet/IP,
PLC-2, PLC-3, PLC-5, PanelBuilder, PowerFlex, PhaseManager, POINT
I/O, PowerFlex, Rockwell Automation, RSBizWare, Rockwell Software,
RSEmulate, Historian, RSFieldbus, RSLinx, RSLogix, RSNetWorx for
DeviceNet, RSNetWorx for EtherNet/IP, RSMACC, RSView, RSView32,
Rockwell Software Studio 5000 Automation Engineering & Design
Environment, Studio 5000 View Designer, SCANport, SLC, SoftLogix,
SMC Flex, Studio 5000, Ultra 100, Ultra 200, VersaView, WINtelligent,
XM, SequenceManager are trademarks of Rockwell Automation, Inc.
Any Rockwell Automation logo, software or hardware product not
mentioned herein is also a trademark, registered or otherwise, of Rockwell
Automation, Inc.
Other Trademarks
CmFAS Assistant, CmDongle, CodeMeter, CodeMeter Control Center, and
WIBU are trademarks of WIBU-SYSTEMS AG in the United States and/or
other countries. Microsoft is a registered trademark of Microsoft Corporation
in the United States and/or other countries. ControlNet is a trademark of
ControlNet International. DeviceNet is a trademark of the Open DeviceNet
Vendors Association (ODVA). Ethernet/IP is a trademark of ControlNet
International under license by ODVA.
All other trademarks are the property of their respective holders and are
hereby acknowledged.
Warranty
This product is warranted in accordance with the product license. The
product’s performance may be affected by system configuration, the
application being performed, operator control, maintenance, and other related
factors. Rockwell Automation is not responsible for these intervening factors.
The instructions in this document do not cover all the details or variations in
the equipment, procedure, or process described, nor do they provide
directions for meeting every possible contingency during installation,
operation, or maintenance. This product’s implementation may vary among
users.
This document is current as of the time of release of the product; however,
the accompanying software may have changed since the release. Rockwell
Automation, Inc. reserves the right to change any information contained in

Preface
10 Rockwell Automation Publication 1756-PM017H-EN-P - February 2018
this document or the software at any time without prior notice. It is your
responsibility to obtain the most current information available from Rockwell
when installing or using this product.
Environmental compliance
Rockwell Automation maintains current product environmental information
on its website at
http://www.rockwellautomation.com/rockwellautomation/about-
us/sustainability-ethics/product-environmental-compliance.page
Contact Rockwell Automation
Customer Support Telephone — 1.440.646.3434
Online Support — http://www.rockwellautomation.com/support/

Rockwell Automation Publication 1756-PM017H-EN-P - February 2018 11
Chapter 1
Store and Load a Project Using a
Memory Card
The memory card allows you to keep a copy of your project on the controller
without the need to maintain power to the controller. You can use a memory
card to store the contents of the user memory when you store the project.
Important: Remember these guidelines with a memory card.
•Changes that you make after you store the project are not
reflected in the contents of the memory card.
•If you make changes to the project but do not store those
changes, you overwrite them when you load the project from a
memory card. If this occurs, you have to upload or download the
project to go online.
•If you want to store changes, such as online edits, tag values, or
a ControlNet network schedule, store the project after you make
the changes.
If a computer loses power and does not have enough energy capacity, it loses
the project in user memory. When this occurs, you can load the copy from
the memory card to the user memory of the controller:
•Whenever it powers up.
•Whenever there is no project in the controller and it powers up.
•Anytime through the Logix Designer application.
A store or load operation from a memory card has these parameters.
Parameter Store and Load
How much time does a store or load operation take? Less than three minutes
What controller mode do I use to store or load a project? Program mode
Can I go online with the controller during a store or load? No
What is the state of the I/O during a store or load? I/O remains in its configured state for Program mode
Introduction

Chapter 1
Store and Load a Project Using a Memory Card
12 Rockwell Automation Publication 1756-PM017H-EN-P - February 2018
These Logix 5000 controllers support a memory card for project storage.
Controller
Type Catalog Number Firmware Revision Supports a 1784-SD1 or 1784- SD2 Secure Digital (SD) Card
CompactLogix
5370
1769-L16ER-BB1B 20.x or later Yes
1769-L18ER-BB1B
1769-L18ERM-BB1B
1769-L24ER-QB1B 21.x or later
1769-L24ER-QBFC1B
1769-L26ER-BB1B
1769-L27ERM-QBFC1B
1769-L30ER 20.x or later
1769-L30ER-NSE
1769-L30ERM
1769-L33ER
1769-L36ERM
Compact
GuardLogix
5370
1769-L30ERMS
1769-L33ERMS
1769-L36ERMS
28.x or later Yes
1769-L37ERMOS 30.x or later
CompactLogix
5380 5069-L306ER
5069-L306ERM
5069-L3100ERM
5069-L310ER
5069-L310ERM
5069-L310ER-NSE
5069-L320ER
5069-L320ERM
5069-L330ER
5069-L330ERM
5069-L340ER
5069-L340ERM
5069-L350ERM
5069-L380ERM
29.x or later Yes
Controllers with
Memory Card
Options

Store and Load a Project Using a Memory Card
Chapter 1
Rockwell Automation Publication 1756-PM017H-EN-P - February 2018 13
Controller
Type Catalog Number Firmware Revision Supports a 1784-SD1 or 1784- SD2 Secure Digital (SD) Card
Compact
GuardLogix
5380
5069-L306ERMS2
5069-L306ERS2
5069-L3100ERMS2
5069-L3100ERS2
5069-L310ERMS2
5069-L310ERS2
5069-L320ERMS2
5069-L320ERS2
5069-L330ERMS2
5069-L330ERS2
5069-L340ERMS2
5069-L340ERS2
5069-L350ERMS2
5069-L350ERS2
5069-L380ERMS2
5069-L380ERS2
31.x or later Yes
CompactLogix
5480 5069-L45ERMW 31.x or later Yes
ControlLogix
5570
1756-L72
1756-L73
1756-L74
1756-L75
19.x or later Yes
1756-L71 20.x or later
GuardLogix
5570 1756-L71S
1756-L72S
1756-L73S
31.x or later Yes
ControlLogix
5580 1756-L81E
1756-L82E
1756-L83E
1756-L84E
1756-L85E
29.x or later Yes
GuardLogix
5580 1756-L81ES
1756-L82ES
1756-L83ES
1756-L84ES
31.x or later Yes
If the major and minor revisions of the project on the memory card do not
match the major and minor revision of the controller, a major fault may
occur during a load.
The memory card stores the firmware for projects for revision 12.0 or later.
Depending on the current revision of the controller, you may be able to use
the memory card to update the firmware of the controller and load the
project.
Prevent a Major Fault
During a Load

Chapter 1
Store and Load a Project Using a Memory Card
14 Rockwell Automation Publication 1756-PM017H-EN-P - February 2018
Sample ladder logic code for the Logix Designer applications are available
for using your file system on a Logix5000 controller to read and write data
on a memory card. These are the files you need:
•CF_Read_Write.ACD
•CF_Read_Write_Example.ACD
•Logix-AP007B-EN-P.pdf
To access these files, see
http://samplecode.rockwellautomation.com/idc/groups/public/documents/we
bassets/sc_home_page.hcst.
The Logix Designer 1784-CF128 CompactFlash card does not have to be
formatted to store controller information.
If the revision of
your project is Then
11.xThe CompactFlash card uses a special format.
•Use only a Logix5000 controller to store a project on a CompactFlash card.
•Store only a single project and no other data on a CompactFlash card.
•When you store a project on a CompactFlash card, you overwrite the entire contents of the card. In
other words, you lose everything that is currently on the card.
≥12.0 The CompactFlash card uses the FAT16 file system.
If the card Then the controller
Is already formatted for the
FAT16 file system.
•Leaves existing data.
•Creates folders and files for the project and firmware.
The CompactFlash card using the FAT16 file system:
•Stores multiple projects and associated firmware.
•If a card already contains a project with same name, a store overwrites the project on the
CompactFlash card.
•Loads the most recently stored project.
With a revision ≥12.0, you can also use a card reader to read and manipulate the files on a memory
card.
See "Use a Memory Card Reader on page 29."
Read/Write Card Data
CompactFlash Card
Formatting

Store and Load a Project Using a Memory Card
Chapter 1
Rockwell Automation Publication 1756-PM017H-EN-P - February 2018 15
A Secure Digital (SD) memory card (catalog numbers 1784-SD1 (1 GB),
1784-SD2 (2 GB) that uses the FAT 16 file system does not have to be
formatted when storing a project to a controller.
If the revision of your
project is Then
≥18.0 The SD card uses the FAT16 file system.
If the card: Then the controller:
Is unlocked.
•Leaves existing data.
•Creates folders and files for the project and firmware.
Is locked.
•Does not allow writing to the card.
The SD card using the FAT16 file system:
•Stores multiple projects and associated firmware.
•Overwrites the project on the card if it contains a project with the same name
•Loads the most recently stored project.
You also can use a card reader to read and manipulate the files on a memory card.
See "Use a Memory Card Reader on page 29."
See "Store a Project on page 18" for loading an SD card in the controller.
This table outlines the options and precautions for updating the firmware of a
controller that has a memory card.
If Then
You meet all of these conditions.
•The controller has a memory card.
•The project on the memory card has
a revision ≥12.0.
•The project on the memory card has
a Load Image option = On Power
Up or On Corrupt Memory.
•A controller in service has a
revision ≥12.0.
Update the firmware by using one of these options.
•Memory card
•Logix Designer application
•ControlFLASH™ software (See the Important: note on the next page)
Follow this procedure to update the firmware and load the project by using the
memory card.
1.Install the card in the controller.
2.If the Load Image option = On Corrupt Memory and the controller contains a
project, before powering down, disconnect the battery or disengage the Energy
Storage Module (ESM) from the controller.
3.Turn on or cycle power to the controller.
Follow this procedure if you use the Logix Designer application or ControlFLASH
software to update the firmware.
1.
Remove the card from the controller. This prevents the controller from setting the
Load Image option of the memory card to User Initiated during the update.
2.After the firmware update is completed, store the project to the memory card.
This ensures that the revision of the project on the memory card matches the
revision of the controller.
Secure Digital Card
Formatting
Perform Firmware
Updates

Chapter 1
Store and Load a Project Using a Memory Card
16 Rockwell Automation Publication 1756-PM017H-EN-P - February 2018
If Then
You do not meet all of the preceding
conditions. Update the firmware by using either:
•Logix Designer application.
•ControlFLASH software. See the Important: note on the next page.
Take these precautions.
•Before you update the firmware either:
•Remove the memory card from the controller.
•Check the Load Image option of the memory card. If it is set to On
Power Up or On Corrupt Memory, store the project with the Load
Image option set to User Initiated.
Otherwise, a major fault may occur when you update the controller firmware.
This occurs because the On Power Up or On Corrupt Memory options cause
the controller to load the project from the memory card. The firmware
mismatch after the load causes a major fault.
•After you update the firmware, store the project to the memory card
to ensure the
revision of the project on the memory card matches the revision of the controller.
Important: Make sure the SD card is unlocked if set to load On Power Up
before using the ControlFLASH software. Otherwise, the updated
data may be overwritten by firmware on the SD card. An error
message appears. Refer to the ControlLogix System User Manual,
publication 1756-UM001 available at
http://literature.rockwellautomation.com/idc/groups/literature/docum
ents/um/1756-um001_-en-p.pdf, before updating.
Also, while it’s not required for operation, leave the SD card
installed in the controller. The SD card saves extended diagnostic
information that you can send to Rockwell Automation that
provides enhanced diagnostics of your controller application and
firmware should circumstances require this data.
You have several options for when (under what conditions) to load the
project into the user memory (RAM) of the controller.
If you want to load an image
Then choose
Notes
Whenever you turn on or cycle the chassis
power On Power Up
•During a power cycle, online changes, tag values,
and network schedules that you have not stored
on the memory card are lost.
•Loading from a memory card may also change
the firmware of the controller. For more
information, see "Perform Firmware Updates on
page 15."
•You can use the Logix Designer application to
load the project.
When to Load an
Image

Store and Load a Project Using a Memory Card
Chapter 1
Rockwell Automation Publication 1756-PM017H-EN-P - February 2018 17
If you want to load an image Then choose Notes
Whenever there is no project in the
controller and you turn on or cycle the
chassis power
On Corrupt Memory
•For example, if the battery becomes discharged
or the ESM is disengaged and the controller loses
power, the project is cleared from memory. When
power is restored, this load option loads the
project back into the controller.
•Loading from a memory card may also change
the firmware of the controller. For more
information, see "Perform Firmware Updates on
page 15."
•You can use the Logix Designer application to
load the project.
Only through the Logix Designer
application User Initiated
The following table provides load option examples.
Table 2 - Load Option Examples
Example Description
Load Image = On Power Up
Load Mode = Program 1.You update the firmware of the controller to the desired revision.
2.You store the project for the controller on the memory card.
3.When you turn on power to the controller after installation, the project
loads into the controller.
4.The controller remains in Program mode.
Load Image = On Corrupt Memory
Load = Run
1.You store the project for the controller on the memory card (the major
and minor revisions of the firmware in the controller match the major
and minor revisions of the project on the memory card.)
2.If the battery discharges or the ESM is disengaged and power to the
controller is interrupted, the project is cleared from the controller
memory.
3.When power is restored, the project automatically loads into the
controller and the controller returns to Run mode.
Load Image = On Power Up
Load Mode = Program
Revision ≥12.0
1.The controller fails.
2.You remove the memory card.
3.You replace the failed controller with a new controller.
4.You replace the memory card.
5.When you turn on the power, the firmware and project load into the
controller. The controller remains in Program mode.
Load Image = On Power Up
Load Image = Not applicable 1.You want to load a different project into your controller.
2.A memory card contains the desired project.
3.With the memory card installed in the controller, you use the Logix
Designer application to load the project into the controller.

Chapter 1
Store and Load a Project Using a Memory Card
18 Rockwell Automation Publication 1756-PM017H-EN-P - February 2018
This section explains how to store a project on the memory card of the
controller.
ATTENTION:
During a store operation, all active servo axes are turned
off. Before you store a project, make sure that this does not cause any
unexpected movement of an axis.
Before you store the project:
•Make all the required edits to the logic.
•Download the project to the controller.
•Schedule your ControlNet networks.
Follow these steps to store a project.
1. Go online with the controller.
2. Put the controller in Program Mode (Rem Program or Program).
3. On the Online toolbar, click the Controller Properties icon.
Tip: For 1756-L7xcontrollers only, Energy Storage instead of Battery
OK appears beside the Controller Properties icon. Refer to the
ControlLogix System User Manual, publication 1756-UM001
available at
http://literature.rockwellautomation.com/idc/groups/literature/docu
ments/um/1756-um001_-en-p.pdf, for information on the Energy
Storage Module.
4. On the Controller Properties dialog box, click the Nonvolatile
Memory tab and then click Load/Store.
Store a Project

Store and Load a Project Using a Memory Card
Chapter 1
Rockwell Automation Publication 1756-PM017H-EN-P - February 2018 19
Important: At the bottom of the Nonvolatile Memory tab, a message
appears if the CompactFlash card or SD card is empty.
A message also appears if the SD card is locked.
5. At the bottom of the Nonvolatile Memory tab, select Inhibit
Automatic Firmware Update checkbox if you do not want to
automatically store an image during a Save or Load operation.
6. Choose when (under what conditions) to load the project back into the
user memory (RAM) of the controller.
Description
The project that is currently on the memory card of the controller (if
any project is there).
The project that is currently in the user memory (RAM) of the
controller.
Store operation.
In the Load Image field, if you choose On Power Up or On Corrupt
Memory, you must also choose the Load Mode you want to controller
to go to after the load.

Chapter 1
Store and Load a Project Using a Memory Card
20 Rockwell Automation Publication 1756-PM017H-EN-P - February 2018
•Remote Program
•Remote Run
7. In the Automatic Firmware Update list, use the default (disable) or
choose the appropriate firmware supervisor.
For details on the firmware supervisor options, see the ControlLogix
System User Manual, publication 1756-UM001 available at
http://literature.rockwellautomation.com/idc/groups/literature/documen
ts/um/1756-um001_-en-p.pdf .
8. Click <-- Store.
Important: Store is not active if the SD card is locked.
A dialog box asks you to confirm the store operation.
9. To store the project, click Yes.
The table describes the events that occur for the memory card being
used.
If using This happens during the store
CompactFlash Card
•On the front of the controller, the OK status
indicator shows the following sequence: flashing
green > solid red > solid green.
•Logix Designer application goes offline.
•A dialog box indicates the store operation is in
progress.
SD Card
•On the front of the controller, the SD and OK
status indicators flash green.
•The Status Display shows SAVE. See the
illustration.
•A dialog box tells you that the store is in
progress.
10. Click OK.