Allen-Bradley 2711-TBDC User manual

Installation Instructions

Original Instructions

Power Terminal Block

Catalog Numbers

2711-TBDC, 2711P-RTBAP, 2711P-RTBDSP, 2711P-RVAC

This document provides instructions on how to remove and install the AC or DC power

terminal block in these PanelView™ terminals.

Summary of Changes

This publication contains new and updated information as indicated in the following table.

Topic Page

Summary of Changes 1

Before You Begin 2

Power Terminal Blocks With A LockingTab 2

Power Terminal Blocks With Two Screws 3

Additional Resources 4

Cat. No. Power Type Install Method Where Used

2711P-RVAC AC Locking tab PanelView Plus 400 and 600

2711P-RTBAP Two screws PanelView Plus 7 Performance

2711-TBDC DC Locking tab PanelView 5310

PanelView Plus 400 and 600

PanelView 600 Touch only

PanelView 300 Micro

2711P-RTBDSP Two screws PanelView Plus 7 Performance

PanelView 5510

Topic Page

Added Install Method column, and 2711P-RTBAP and 2711P-RTBDSP rows to affected terminals table. 1

Separated terminal block replacement instructions by locking tab and two screws methods. 2

Added publications 2711P-UM008 and 2715P-UM001 to the Additional Resources table. 4

2Rockwell Automation Publication 2711-IN021D-EN-P - October 2018

Power Terminal Block

Before You Begin

The terminals have a three-pin terminal block for power connections. You can remove the

terminal block for ease of installation, wiring, and maintenance.

The location of the power terminal block on PanelView terminals can be different, but the

removal and installation steps are the same. For complete details, see the user manual for your

terminal in Additional Resources on page 4.

Power Terminal Blocks With A Locking Tab

For power terminals with a locking tab, perform the following steps.

Remove the Existing Power Terminal Block

To remove the power terminal block, follow these steps.

1. Remove power from the terminal.

2. Disconnect wires from the marked terminals on the terminal block.

3. Insert the tip of a small, flat-blade screwdriver into the terminal block access slot.

4. Gently pry the existing terminal block away from the terminal.

WARNING: Explosion Hazard

• Substitution of components may impair suitability for hazardous locations.

• Do not disconnect equipment unless power has been switched off and area is known to be

non-hazardous.

• Do not connect or disconnect components unless power has been switched off.

• All wiring must comply with N.E.C. articles 501-4(b), 502-4(b), 503-3(b) as appropriate.

• Peripheral equipment must be suitable for the location it is used in.

ATTENTION: AC and DC terminal blocks are keyed and marked differently. Do not force terminal

blocks into connectors. If the terminal block does not fit in the terminal, verify that you are using

the correct terminal block for your terminal.

PanelView 5310 TerminalPanelView Plus 400 and 600 Terminals

Insert Pry

Rockwell Automation Publication 2711-IN021D-EN-P - October 2018 3

Power Terminal Block

Install the New Power Terminal Block

To install the power terminal block, follow these steps.

1. Press the base of the power terminal block into position.

2. Gently push the top of the terminal block back to the vertical position to snap in the

locking tab.

3. Reconnect wires to the marked terminals on the terminal block.

4. Restore power to the terminal.

Power Terminal Blocks With Two Screws

For power terminals with two screws, perform the following steps.

Remove the Existing Power Terminal Block

To remove the existing power terminal block, follow these steps.

1. Remove power from the terminal.

2. Disconnect wires from the marked terminals on the terminal block.

3. Loosen the two screws that secure the terminal block.

4. Gently pull the terminal block away from the connector.

Install the New Power Terminal Block

To install the new power terminal block, follow these steps.

1. Attach the new terminal block to the connector until seated.

2. Tighten the two screws to secure the terminal block to the connector.

3. Reconnect wires to the marked terminals on the terminal block.

4. Restore power to the terminal.

DC Terminal Block AC Terminal Block

Allen-Bradley, PanelView, and Rockwell Automation are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400

Rockwell Automation maintains current product environmental information on its website at

http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

DIR 10003635375_01

Publication 2711-IN021D-EN-P - October 2018 Vendor part number xxxxxxxxxx

*PN-517952*

PN-517952

Additional Resources

These documents contain additional information about related products from Rockwell

Automation.

You can view or download publications at http://www.rockwellautomation.com/global/

literature-library/overview.page. To order paper copies of technical documentation, contact your

local Allen-Bradley distributor or Rockwell Automation sales representative.

Resource Description

PanelView 5310 Terminal User Manual,

publication 2713P-UM001