Allen-Bradley 1797-TB3S User manual

FLEX Ex is a trademark of Rockwell Automation. 1797-5.2 - September 1999
Installation Instructions
FLEX Ex Spring Clamp Terminal Base
(Cat. No. 1797-TB3S)
You will need to rotate the keyswitch (4) to the correct position depending
on the module. Refer to the module’s installation instructions for more
information. Do not change the position of the keyswitch after wiring
the terminal base unit.
Component Identification
1Female flexbus connector
2Terminal base unit
3Male flexbus connector
4Keyswitch - Set to the position required for the installed module
5Mounting holes for panel mounting
6, 7, 8 Input/output terminal strips for connecting input/output wiring, -V,
+V connections, chassis grounds
9Locking tab
10 Module locking latch
11 Cover plug for male flexbus connector
12 96 pin female I/O connector
1
5
6
7
89
2
11
3
4
10
41253
Only remove this cover plug if
connecting another terminal
base unit.
12
Allen-Bradley

2FLEX Ex Spring Clamp Terminal Base
1797-5.2 - September 1999
Make certain that you only connect terminal base units to other intrinsically
safe system modules or adapters to maintain the integrity of the
intrinsically-safe backplane.
Installation in Zone 1
This terminal base unit must not be exposed to the environment. Provide a
suitable metal enclosure. This terminal base unit has a protection factor of
IP20. Do not remove the flexbus cover on the right-most terminal base unit.
Electrostatic Charge
Protect the system against electrostatic charge. Post a sign near this
module: Attention! Avoid electrostatic charge. For your convenience, a
sign which can be cut out and posted is included in this installation
instruction.
European Community Directive Compliance
If this product has the CE mark it is approved for installation within the
European Community or EEA regions. It has been designed and tested to
meet the following directives.
EMC Directive
This product is tested to meet the Council Directive 89/336/EC
Electromagnetic Compatibility (EMC) by applying the following
standards, in whole or in part, documented in a technical construction file:
•EN 50081-2
EMC - Generic Emission Standard, Part 2 - Industrial Environment
•EN 50082-2
EMC - Generic Immunity Standard, Part 2 - Industrial Environment
This product is intended for use in an industrial environment.
!
ATTENTION: This terminal base unit cannot be used in an
intrinsically safe environment after it has been exposed to
non-intrinsically safe signals.
41307

FLEX Ex Spring Clamp Terminal Base 3
1797-5.2 - September 1999
Ex Directive
This product is tested to meet the Council Directive 94/9/EC (ATEX 100a)
Equipment and Protective Systems Intended for Use in Potentially
Explosive Atmospheres by applying the following standards:
•EN50014:1992, Electrical Apparatus for Potentially Explosive
Atmospheres
•EN50020:1994, Electrical Apparatus for Potentially Explosive
Atmospheres - Intrinsic Safety “i”
Inputs/Outputs
Do not apply any non-instrinsically safe signals to this terminal base.
When using as an intrinsically safe electrical apparatus according to
EN50020, the European directives and regulations must be followed.
The terminals in this terminal base unit may be electrically connected to
each other by the insertion of FLEX Ex I/O modules. See the module
installation instructions to determine this.
Description
The 1797-TB3S terminal base has 36 wiring connections to/from a plug-in
module. The use of each terminal depends on the module mounted in this
base.
The 1797-TB3S terminal base also has connections for cold junction
compensation and terminals designated for shield termination to chassis
ground.
The terminal base is equipped with a factory-installed tab cover for the
backplane bus connection. The tab cover may be removed only when the
terminal base unit is connected to other terminal base units.
Important: When interconnecting several lines, you must consider the
total accumulated power and check for intrinsic safety
requirements.
Allen-Bradley

4FLEX Ex Spring Clamp Terminal Base
1797-5.2 - September 1999
To connect wiring, insert a blade-type screwdriver with a blade width of
0.100-0.120in. (2.54-3.05mm) into the slot above the selected wiring port
and lift up. Insert the wire while holding the screwdriver up. Release the
upward screwdriver pressure to secure the wire.
Mounting on a DIN Rail
1. Remove the cover plug in the male connector of the unit to which you
are connecting this terminal base unit.
!
ATTENTION:
•Make certain that you power this terminal base unit with an
intrinsically safe power supply. Do not exceed the values
listed in the specifications for this terminal base unit.
•Do not use the unused terminals on this terminal base unit.
Using these terminals as supporting terminals can result in
damage to modules and/or unintended operation of your
system.
!
ATTENTION: Do not remove or replace a terminal base unit
when power is applied. Interruption of the flexbus can result in
unintended operation or machine motion.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
18 19 20 21 22 23 3324 25 26 27 28 29 30 31 3217
35 36 37 38 47 48 49 5034 51
16
39 40 41 42 43 44 45 46
Wiring Connections for Terminal Base 1797-TB3S
41254
Row A
Row B
Row C
Label placed at top of wiring area
Row A
Row B
Row C
+V -V -V+V
No connections allowed to terminals 36 and 49

FLEX Ex Spring Clamp Terminal Base 5
1797-5.2 - September 1999
2. Check to make sure that the 16 pins in the male connector on the
adjacent device are straight and in line so that the mating female
connector on this terminal base unit will mate correctly.
3. Make certain that the female flexbus connector is fully retracted into
the base unit.
4. Position the terminal base over the 35 x 7.5mm DIN rail A
(A-B pt. no. 199-DR1).
!
ATTENTION: Do not force the terminal base into the
adjacent modules. Forcing the units together can bend or break
the hook and allow the units to separate and break
communication over the backplane.
A
A
41114
Position terminal base at a slight angle and
hooked over the top of the DIN rail A.
41115
Slide the terminal base over tight against the adapter (or proceeding terminal
base). Make sure the hook on the terminal base slides under the edge of the
adapter and the flexbus connector is fully retracted.
Allen-Bradley

6FLEX Ex Spring Clamp Terminal Base
1797-5.2 - September 1999
5. Rotate the terminal base onto the DIN rail with the top of the rail
hooked under the lip on the rear of the terminal base. Use caution to
make sure that the female flexbus connector does not strike any of
the pins in the mating male connector.
6. For specific wiring information, refer to the installation instructions for
the module you are installing in this terminal base unit.
7. Repeat the above steps to install the next terminal base.
8. Be sure the flexbus connector cover on the last terminal base is in
place.
Wiring
1. Make wiring connections as described in the installation instructions
included with the specific module that mounts on your terminal base
unit.
2. Connect +V and -V from this terminal base unit to the next using
jumpers or individual external wiring, if appropriate due to total
module power consumption.
Press down on the terminal base unit to lock the terminal base on the DIN rail. If
the terminal base does not lock into place, use a screwdriver or similar device to
open the locking tab, press down on the terminal base until flush with the DIN
rail and release the locking tab to lock the base in place.
41116
41117
Gently push the flexbus connector into the side of the
adapter to complete the backplane connection.

FLEX Ex Spring Clamp Terminal Base 7
1797-5.2 - September 1999
!
ATTENTION: Do not use any unused terminals on this
terminal base unit. Using these terminals as supporting
terminals can result in damage to the module and/or
unintended operation of your system.
Daisy-chaining
41110
+V, -V
Wiring when total module current power is less than 8.5W
Combination
Wiring when total module current power is greater than 8.5W 41111
+V, -V
<8.5W
+V, -V
<8.5W
You can use the daisy
chain configuration if
the total module power
draw is <8.5W.
Otherwise, power is
connected to individual
modules.
Other variations are possible depending upon individual module power.
Allen-Bradley

8FLEX Ex Spring Clamp Terminal Base
1797-5.2 - September 1999
Mounting Dimensions
Repair
This terminal base unit is not field-repairable. Any attempt to open this
terminal base unit will void the warranty and IS certification. If repair is
necessary, return this module to the manufacturer.
About the Mounting Kit
Use the optional 1794-NM1 mounting kit to mount your system on a panel
or wall without a DIN rail.
41342
3.7
(94)
2.7
(69)
3.7
(94)
Inches
(Millimeters)
1794-NM1
Mounting Kit with
18 screws (2 screws for the
adapter and 2 screws for
each module)
30238

FLEX Ex Spring Clamp Terminal Base 9
1797-5.2 - September 1999
1797-TB3S Specifications
Number of Terminals 1 row of 16, 2 rows of 18
Terminal Type Spring-clamp - To open, insert bladed
screwdriver (0.100 - 0.120in/2.54-3.05mm)
and lift up.
Terminals Assignments
+34, -35, +50, -51, and 96
pin female I/O connector
pinsi30-32, 62-64, 94-96i
36, 49
All Other Terminals
Only for intrinsically safe circuits
Ui<10V dc
Ii<2.5A
Ci<1nF
LiNegligible
Must not be used for any connection
Ui<30V dc
Ii<100mA
Ci<1nF
LiNegligible
Flexbus Connection
Intrinsically Safe Ui<10V dc
Ii<400mA
Ci<1nF
LiNegligible
Isolation Voltage Channel-to-channel isolation determined by
inserted module
Weight 200g (approximately)
Dimensions (with module
installed in base) Inches
(Millimeters) 3.7H x 3.7W x 2.7D (94H x 94W x 69D)
Environmental Conditions
Operational Temperature
Storage Temperature
Relative Humidity
Shock Operating
Non-Operating
Vibration
-20 to 70oC (-4 to 158oF)
-40 to 85oC (-40 to 185oF)
5 to 95% noncondensing
Tested 15g peak acceleration, 11 (±1)ms pulse
width
Tested 15g peak acceleration, 11 (±1)ms pulse
width
Tested 2g @ 10-500Hz per IEC 68-2-6
Conductors Wire Size 12 gauge (4mm2) stranded maximum
1.2mm (3/64in) insulation maximum
Agency Certification II 2G EEx ia IIC T4
Class I Division 1 & 2 Groups A-D T4
Class I Zone 1 & 2 AEx ia IIC T4
Certificate of Conformity DMT 98 ATEX E012 U
Termination connections are unique with each I/O module. Refer to the
appropriate I/O module’s installation instructions.
Allen-Bradley

10 FLEX Ex Spring Clamp Terminal Base
1797-5.2 - September 1999
13
24
+V +V
-V -V
2.0
(50)
.83 (21)
1.4
(35.5)
2.3
(58.5)
1.4
(35.5)
2.3
(58.5)
1.4
(35.5)
1.6
(40.5) .61
(15.6)
.3
(8)
Cable length
approximately
11.5 (292.1) or
35.5 (901.0)
from
upper connector
[length depends
upon cable
-1ft (0.3m) or
ATTENTION: Be careful of metal chips when drilling cable mounting holes. Do not drill holes above a system that has any modules installed.
!
Inches
(Millimeters)
40871