Alliance Laundry Systems Cygnus Ultra Pro Owner's manual

Programming
www.alliancelaundry.com
Washer-Extractor
Cygnus Ultra Pro
Refer to Page 3 for Model Numbers
CYGNUS
ULTRA PRO
B12583501
Open door
Abra la puerta
Select cycle
Seleccione el ciclo
Add detergent
Añade de detergente
Close door
Cierre la puerta
Push to start
Pulse para iniciar
CFD1176R
Part No. D1563
January 2014
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
D1563 1
NOTE: The WARNING and IMPORTANT
instructions appearing in this manual are not meant
to cover all possible conditions and situations that
may occur. It must be understood that common
sense, caution, and carefulness are factors which
cannot be built into these washer-extractors. These
factors MUST BE supplied by the person(s)
installing, maintaining, or operating the washer-
extractor.
Always contact the distributor, service agent, or the
manufacturer about any problems or conditions you do
not understand.
Failure to install, maintain, and/or operate
this machine according to the
manufacturer's instructions may result in
conditions which can produce bodily injury
and/or property damage.
W030
WARNING

© Copyright 2014, Alliance Laundry Systems LLC
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any
means without the expressed written consent of the publisher.
2D1563
© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Table of
Contents
Model Identification ........................................................................... 3
Preliminary Information.................................................................... 4
About the Control ................................................................................. 4
Glossary of Terms................................................................................. 4
Power Failure Recovery ....................................................................... 4
Communications ................................................................................... 4
Control Identification......................................................................... 5
Selection Keypads ................................................................................ 5
Display Identification ......................................................................... 6
Cycle Screen ......................................................................................... 6
Special Features .................................................................................. 9
Programming Control ........................................................................... 9
Viewing Control Information ............................................................... 9
Testing Machine Components .............................................................. 9
Rapid Advance Feature......................................................................... 9
Communication Mode .......................................................................... 9
Washer-Extractor Operation ............................................................ 10
Start Up................................................................................................. 10
Start Mode ............................................................................................ 10
Run Mode ............................................................................................. 10
Stop Mode............................................................................................. 10
End of Cycle Mode............................................................................... 10
The Non-Active Menu ........................................................................ 11
What is Available in the Non-Active Menu? ....................................... 11
Non-Active Menu Navigation.......................................................... 12
Non-Active Menu Options ................................................................... 13
1. Logbook Sub-Menu ..................................................................... 13
2. Info Sub-Menu ............................................................................. 14
3. Advanced Functions Sub-Menu................................................... 17
3.1 Test Menu .................................................................................. 18
3.2 Edit Menu................................................................................... 24
3.3 Edit Menu Subroutine ................................................................ 30
3.4 Settings Menu ............................................................................ 31
Cycle Charts ........................................................................................ 36
Error Messages ................................................................................... 41
Events................................................................................................... 44
Rapid Advance Feature...................................................................... 46
How to Use Rapid Advance............................................................. 46
Communication Mode ........................................................................ 47
Infra-red Communications.................................................................... 47

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
D1563 3
Model Identification
Information in this manual is applicable to these
washer-extractor models:
CH040_ULTRA-PRO
CH055_ULTRA-PRO
CH075_ULTRA-PRO
CH090_ULTRA-PRO
CHR040R
CHR055R
CHR075R
CHR090R
CS018_ULTRA-PRO
CS025_ULTRA-PRO
CS035_ULTRA-PRO
CS055_ULTRA-PRO
CS075_ULTRA-PRO
CS100_ULTRA-PRO
CS135_ULTRA-PRO
CS165_ULTRA-PRO
CXR018R
CXR025R
CXR035R
CXR055R
CXR075R
CXR100R
CXR135R
CXR165R
IH014_ULTRA-PRO
IH018_ULTRA-PRO
IH025_ULTRA-PRO
IH030_ULTRA-PRO
IH040_ULTRA-PRO
IH055_ULTRA-PRO
IH075_ULTRA-PRO
IH090_ULTRA-PRO
IHR014R
IHR018R
IHR025R
IHR030R
IHR040R
IHR055R
IHR075R
IHR090R
IS012_ULTRA-PRO
IS018_ULTRA-PRO
IS025_ULTRA-PRO
IS035_ULTRA-PRO
IS055_ULTRA-PRO
IS075_ULTRA-PRO
IS100_ULTRA-PRO
IS135_ULTRA-PRO
IS165_ULTRA-PRO
IXR012R
IXR018R
IXR025R
IXR035R
IXR055R
IXR075R
IXR100R
IXR135R
IXR165R

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
4D1563
Preliminary Information
About the Control
This control is an advanced, programmable computer
that lets the operator control machine features by
pressing a sequence of keypads. Refer to Figure 1.
The control allows the operator to obtain information
from the machine, run test cycles, modify the control’s
programmable features, set the service counters and
view the error code history. Refer to The Non-Active
Menu section for a list of features.
IMPORTANT: In the event of a power failure, the
control will not have to be reprogrammed. It is
designed with a memory system that will remember
how it was programmed until the electrical power
is restored.
IMPORTANT: It is extremely important that the
washer-extractor has a good ground connection and
that all mechanical and electrical connections to the
control are made before applying power to or
operating the washer-extractor.
Glossary of Terms
The following are a few terms and abbreviations to
learn. These are referred to throughout the instructions.
Display – This term refers to the window area of the
control that displays words and values.
Power Failure Recovery
If a cycle is in progress and the power fails, the water
will be drained from the machine and the door can be
opened after approximately 3 minutes. If the door is not
opened and the power failure is shorter than 2 weeks,
the washer-extractor will resume the previously active
cycle.
If the door is opened or if the length of the power failure
is longer than 2 weeks, the control will end the cycle
and the display will revert back to Start Mode.
Communications
The control may be programmed manually or by infra-
red communication with an external device.
Infra-red Communications
A PC allows the owner to program and retrieve
information from the control without using the
machine’s keypad, which greatly expands the
programming options available to the owner. However,
it is not required to program and operate the washer-
extractor. The operation of a PC and the advanced
features available are covered separately in the
instructions included with the PC programming
software, Cygnus Assist.

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
D1563 5
Control Identification
Selection Keypads
(Refer to Figure 1)
The Selection keypads are used in various combinations
to obtain information from the machine, run wash
cycles, run test cycles, modify the control’s
programmable features, set the service counters and
view the error code history. These instructions cover
the manual programming and data retrieval options.
CFD1176R
1Display 3Selection keypads
2Optical Download Window 4Start/Stop keypad
Figure 1
CYGNUS
ULTRA PRO
B12583501
Open door
Abra la puerta
Select cycle
Seleccione el ciclo
Add detergent
Añade de detergente
Close door
Cierre la puerta
Push to start
Pulse para iniciar
CFD1176R
1
32
4

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
6D1563
Display Identification
Cycle Screen
Title Bar (Refer to Figure 2, Item 1)
Displays the cycle.
Cycle Phase Bar (Refer to Figure 2, Item 2)
Displays how the various phases of the cycle are
progressing. The active phase is highlighted.
CFD1177R
1Title Bar 6Water Level
2Cycle Phase Bar 7Next Screen
3Step Bar 8Navigation
4Cycle Time Remaining 9Info
5Water Temperature
Figure 2
CFD1177R
4. HOT WASH
40 °C
26
27°C
1h 09
1
2
3
4
5
6
7
8
9
Wash Cycle
Rinse Cycle
Spin Cycle
Tabl e 1
CFD202R
CFD203R
CFD204R
CFD205R

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Display Identification
D1563 7
Step Bar (Refer to Figure 2, Item 3)
Displays the phase components. The active component
appears in the selection box.
Table 2
Cycle Time Remaining
(Refer to Figure 2, Item 4)
Displays the remaining program time.
Figure 3
Water Temperature (Refer to Figure 2, Item 5)
Displays the temperature of the water. This symbol is
flashing when heating is activated.
Figure 4
Water Level (Refer to Figure 2, Item 6)
Displays the water level in the wash tub. This symbol
is flashing when machine is filling.
Figure 5
Next Screen (Refer to Figure 2, Item 7)
View the next screen.
Figure 6
Proceed - Return (Refer to Figure 2, Item 8)
Tabl e 3
Symbol Description
CFD206R Wash Phase
CFD207R
Wash Action
CFD208R
Heating
CFD209R
Controlled Heating
CFD210R
Drain
CFD213R Water Inlet
CFD214R Water Level Time Stop
CFD215R
Heating Time Stop
CFD216R
Time
CFD217R
Spin
CFD218R Subroutine
CFD219R Water Level
CFD220R Soap Inlet
CFD221R
Cool Down
CFD222R Hold
CFD223R Relay Contact
CFD224R
Predefined Start
CFD226R
CFD227R
CFD1178R
CFD426R
CFD261R
Go to the next component.
CFD423R
Restart the current phase.
CFD424R
Start the next phase.
CFD425R
Resume the previous or first
phase.
1h 27
13°C
23.0

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT
Display Identification
8D1563
Info (Refer to Figure 2, Item 9)
Displays information on the active component:
Table 4
Symbol Description
Level Stop: Target level is
displayed.
CFD1179R CFD214R
Heat Stop: Target temperature.
CFD230R CFD215R
Time: Time remaining.
CFD231R CFD216R
Drain: Selected drain.
CFD232R CFD210R
Spin: Set spin speed and remaining
spin time.
CFD233R CFD217R
Cool-down: Target temperature
and drop in temperature per minute.
CFD234R CFD221R
Controlled Heating: Target
temperature and rise in temperature
per minute.
CFD235R CFD209R
Waiting: Remaining waiting time
and self-composed comment.
CFD236R CFD222R
Predefined Start: Time at which
the program will start or resume.
CFD237R CFD224R
15
40 °C
12min25
1
1
500
min
rpm
00
40 °C
2.0
°C
min
40 °C
2.0
°C
min
1h59
Explanation
Explanation
Explanation
8:00