Allnet ALL-SG8310PM User manual

ALL-SG8310PM
8 Port Gigabit Smart Managed
HPoE Switch
USER MANUAL

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 2 of 51
Contents
CHAPTER 1PRODUCT INSTRUCTION................................................................................................ 5
1.1 Introduction ................................................................................................................ 5
1.2 Front Panel.................................................................................................................... 5
1.3 Rear Panel........................................................................................................................ 6
CHAPTER 2PREPARATIONS BEFORE INSTRUCTION ............................................................................. 6
2.1 Precautions ...................................................................................................................... 6
2.2 Check Installation Environment................................................................................... 6
2.3 Installation Tools........................................................................................................... 7
CHAPTER 3INSTALLATION............................................................................................................. 7
3.1 Install the Switch........................................................................................................... 7
3.2 Test after Installation.................................................................................................... 7
CHAPTER 4TECHNICAL SPECIFICATIONS ......................................................................................... 8
4.1 Hardware Features: ......................................................................................................... 8
4.2 Software Features: .......................................................................................................... 8
PART TWO WEB CONFIGURATION GUIDE...................................................................... 11
CHAPTER 1USER LOGIN ............................................................................................................. 11
CHAPTER 2SWITCH STATUS ........................................................................................................ 12
2.1 System Information .................................................................................................... 12
2.2 Logging Message ........................................................................................................ 12
2.3 Port Counters .............................................................................................................. 13
2.4 Link Aggregation........................................................................................................ 13
2.5 LLDP Statistics.............................................................................................................. 14
2.6 IGMP Statistics............................................................................................................. 14
2.7 STP Statistics................................................................................................................ 15
2.8 MAC Address Table..................................................................................................... 15
CHAPTER 3BASIC CONFIGURATION .............................................................................................. 16
3.1 IP Configuration ............................................................................................................ 16
3.2 Account Configuration............................................................................................... 17
3.3 Logging Setting .......................................................................................................... 17
3.4 Port Setting ................................................................................................................. 18
CHAPTER 4ADVANCED CONFIGURATION ...................................................................................... 19
4.1 Port Mirror Configuration ............................................................................................ 19
4.2 Port Aggregation .......................................................................................................... 20
4.3 VLAN Management .................................................................................................... 21
4.4 Voice VLAN.................................................................................................................. 22
4.5 Multicast Configuration ............................................................................................. 23
4.6 IGMP Snooping Configuration................................................................................... 24
4.7 Jumbo Frame Configuration......................................................................................... 24
4.8 Static MAC Address Table ............................................................................................. 25
4.9 Dynamic MAC Address Configuration.......................................................................... 25
4.10 LLDP Configuration .................................................................................................. 26
4.11 SNMP Configuration................................................................................................. 26

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 3 of 51
4.12 PoE Management ........................................................................................................ 28
CHAPTER 5NETWORK SECURITY.................................................................................................. 29
5.1 Port Limit Configuration ............................................................................................ 29
5.2 Storm Control.............................................................................................................. 31
5.3 Port Isolation............................................................................................................... 32
5.4 DoS configuration....................................................................................................... 32
5.5 STP Configuration....................................................................................................... 33
CHAPTER 6SYSTEM MAINTENANCE ............................................................................................. 35
6.1 Reboot Switch............................................................................................................. 35
6.2 Factory Reset............................................................................................................... 35
6.3 Firmware Upgrading .................................................................................................. 36
6.4 Ping Test ...................................................................................................................... 36
6.5 Network Cable Test..................................................................................................... 36
APPENDIX TROUBLE SHOOTING ................................................................................. 37
SAFETY WARNINGS & CE LINKAGE .............................................................................. 38
GPL………. ..................................................................................................................... 39

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 4 of 51
Packaging list:
1x ALL-SG8310PM
1x Power Cord
1x CD/QIG
1x Installation accessories kit
Please contact local reseller or distributor if any accessories are missing.

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 5 of 51
Part One Hardware Installation Guide
Chapter 1 Product Instruction
1.1 Introduction
ALL-SG8310PM: 8*10/100/1000M PoE ports, 2*1000 Base-X SFP; 1*Console port.
Switches.
1.2 Front Panel
1. ALL-SG8310PM
8*10/100/1000M PoE ports, 2*1000 Base-X SFP; 1*Console port.
Picture 1.2.1 ALL-SG8310PM Front Panel
LED Indicator Instruction
Please check the LED indicators on the left of front panel.
1. Power Indicator
The power indicator is on the upper-left side of front panel, it is on when the switch is
powered. If the indicator is off, please check the power supply.
2. System Indicator
Over the power indicator is the system indicator, it flashes when switch works normally.
3. 10/100Mbps Link/ACT Indicators
The indicators marked with numbers are yellow when the 10/100M ports
auto-negotiate connected, and the yellow indicators flash when there are data
communications through the ports.
4. 1000Mbps Link/ACT Indicators
The indicators marked with numbers are green when the 1000Mbps ports
auto-negotiate connected, and the green indicators will flash when there are data
communications through the ports.

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 6 of 51
1.3 Rear Panel
Picture 1.3.1 ALL-SG8310PM Rear Panel
Power Socket: Three-core power socket is adopted, please connect female
head of power cord to the socket, and connect the AC power supply with
male head.
Chapter 2 Preparations before Instruction
2.1 Precautions
Please read the following precautions carefully before operation, to avoid damaging
the device or causing body injuries.
1). Please remove the power socket before cleaning the switch. Don’ wipe the switch
with wet cloth or wash the switch with liquid.
2). Don’t stock the device in damp environment or near water, to avoid water or
moisture penetrating into the inner device.
3). Don’t put the device on a unstable box or desk, the device will get damaged from
falling.
4). Please keep good ventilation indoor, and make sure the heat dissipation function of
switch works well.
5). The switch only works normally in suitable voltage. Please check the working voltage
first.
6). Please don’t open the switch enclosure randomly, especially when the switch is
powered on, there is risk of electric shock.
7). Please wear anti-static wrist strap when change the interface board, to avoid the
static electricity damage the board.
2.2 Check Installation Environment
The switch is for indoor use only, please pay attention to the following problems when
install the switch in a cabinet or put the device directly on the desktop.
1) The air vents of switch must have enough space to dissipate the heat inside
enclosure.
2) A good heat dissipation system in the cabinet or on the desktop.
3) The cabinet or desktop strong enough to support the weight of switch and

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 7 of 51
installation accessories.
4) Safe ground connection for the cabinet or desktop.
2.3 Installation Tools
1) Flathead screw driver
2) Cross screw driver
3) Anti-static wrist strap
Chapter 3 Installation
3.1 Install the Switch
3.1.1 Install the switch on a 19 inch standard cabinet
1) First fix the provided two L-shaped brackets on the two sides of switch.
2) Fix the switch on the rack with screws (screws are not provided).
Picture 3.1.1 Cabinet Installation
3.1.2 Install the switch on the desktop
When there is no 19 inch standard cabinet, the switch is usually put on clean desktop.
The operation is easier, please follow the below instructions:
1) Keep the desktop stable and safely grounded.
2) Set aside 10cm space around switch for heat dissipation.
3) Don’t put any heavy device on the switch.
3.2 Test after Installation
Make sure the working voltage is the same with the rated voltage of switch.
Check the connection of grounded cord.
Check the connection of configuration cable and power input cord.
If the interface cable is partly deployed outdoor, please check the connection of
anti-thunder
AC power strip and interface anti-thunder device.

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 8 of 51
Chapter 4 Technical Specifications
4.1 Hardware Features:
Item ALL-SG8310PM
Fixed Ports 8*10/100/1000 Base-T
2*1000 Base-X SFP
PoE standards IEEE802.3af/at
Max Output Power(single
port) 30W
Total Power Consumption 150W
PoE Pin-out 1/2(+)，3/6(-)；Customized 4/5(+),7/8(-)
Switching Capacity ≥16Gbps
Forwarding Mode Full wire-speed storage and forwarding
Forwarding Rate
10M：14880pps/port
100M：148809pps/port
1000M：1488095pps/port
Operation Temperature -20~50°C
Storage Temperature -40~70°C
Operation Humidity 10%～90%(non-condensing)
Storage Humidity 5%～95%(non-condensing)
Dimensions 280（L)*180(W)*44(H)mm
Input Power Supply AC：90-264V ~ 50-60Hz/150W
Weight <2Kg
LED Indicator Power，Link/Act，PoE Status
Energy Saving Comply with “EEE” Energy Efficient Ethernet
4.2 Software Features:
Item ALL-SG8310PM
Protocol
and Standards
IEEE 802.3, 10 BASE-T Ethernet
IEEE 802.3ad, Static or Dynamic Link Aggregation
IEEE 802.3u,100 BASE-TX
IEEE 802.3ab,1000 BASE-T
IEEE 802.3z,1000 BASE-X
IEEE 802.3x,Full-Duplex Flow Control
IEEE 802.1q,VLAN
IEEE 802.1p,QoS/CoS
IEEE 802.1d, Spanning Tree Protocol
IEEE 802.1w,Rapid Spanning Tree Protocol

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 9 of 51
IEEE 802.3az,EEE(Energy Efficient Ethernet)
IEEE 802.1s,Multiple Spanning Tree Protocol
MAC Address 8K MAC addresses
Support auto-update, two-way learning
VLAN
Supports VLAN based on ports, protocols and ACL
Maximum 4K VLANs
VLANs based on IEEE 802.1q
Spanning Tree
STP Spanning Tree Protocol
RSTP Rapid Spanning Tree Protocol
MSTP Multiple Spanning Tree Protocol
Port Aggregation 8 aggregation groups,each containing up to 8 ports;
Port Mirroring Many-to-one mirroring(that is, multiple mirroring ports,
and one monitor port)
Loop Protection Ring protection, real-time detection/quick alarm/accurate
location/intelligent blocking/auto-recovery
Port Isolation Isolate the communication between ports, only uplink
permitted
Traffic Control Back-pressure traffic control under Half-Duplex mode
IEEE 802.3x traffic control under Full-Duplex mode
Flow Rate Limitation Port-based ingress or egress rate limiting
Multicast IGMPv1/v2/v3 and MLDv1/2 Snooping
Storm Suppression
Supports multiple storm suppression:UC,MC,unknown
cast and broadcast.
Storm suppression based on bandwidth
adjustment,storm filtering and ACL
Supports attack against strategy, against Land attack,Blat
attack,Ping attack and TCL controued Flag attack.
Binding of user port ,IP address and MAC address
Security limitation based on port MAC address quantity
QOS
SP（Strict Priority)
WFQ (Weighted Fair Queuing)
WRR (Weighted Round Robin)
Random Early Detect(RED)
Weighted Random Early Detection(WRED)
Head of Line
802.1p (Port Queuing Priority)
DSCP Priority(Differentiated Service Code Point)
Standard Wiring Support Auto-MDIX
Negotiation Mode Auto-negotiation
System Maintenance
Check the connectivity of network cables
Upload/Download configuration files
Upload upgrade patch
View system log

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 10 of 51
Supports factory reset
Management
Visual web interface management
CLI management
Telnet management
SNMP management

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 11 of 51
Part Two WEB Configuration Guide
Chapter 1 User Login
Switch adopt Web-based interface management, the default IP is 192.168.2.1. Please
make sure the IP address of PC is in the same network segment with that of switch, or
the PC can’t access to manage the switch. After the setting of IP address, please input
192.168.2.1 in the browser to access the configuration interface of switch.
The Web management interface consists of five parts, which are switch status, basic
configuration, advanced configuration, network security, system maintenance.
Picture 1.1.1 Login Page
Enter username and password in the above login page, the default username and
password is admin. The system only support single user login, other logins will be
refused until the user logs out.
If IP address conflict occurs, it suggests the latest user didn’t log out successfully. Please
reboot the device or try to log in again180s later.
It is advised to reset the IP address and password in first login, and make sure the switch
is not configured in the same network segment with DHCP server or Internet Gateway
device.

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 12 of 51
Chapter 2 Switch Status
2.1 System Information
Picture 2.1.1 System Information
Device status can be checked in the above page, which contains: Device Model
number(equipment type), PCB/HW Version, MAC Address,Serial Number(System Object
ID), Firmware Version, Firmware Updated Date, System Running Time(System Up Time).
2.2 Logging Message
Picture 2.2.1 Logging Message
System log can be checked in above page. Maintenance technicians can check the
history system log.

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 13 of 51
2.3 Port Counters
Picture 2.3.1 Port Counters
The above picture shows switch port statistics. Users can check the sent/received
bytes,sent/received packets, wrongly sent/received packets. If there are too many wrong
packets, it suggests the port has very poor working performance, the user need to
examine the connection of network cable or the partner network card.
The current software version doesn’t support real-time statistics refresh, please click
“Refresh” button to get new statistics.
2.4 Link Aggregation
Picture 2.5.1 Link Aggregation

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 14 of 51
In above Link Aggregation page, user can check the port aggregation information.
Like aggregator group (LAG), link state, aggregator group member state
(active/standby).
2.5 LLDP Statistics
Picture 2.6.1 LLDP Statistics
LLDP information can be checked in above page. When enable the LLDP(Link Layer
Discovery Protocol ) function, LLDP information of switch ports can be checked here.
2.6 IGMP Statistics

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 15 of 51
Picture 2.7.1 IGMP Statistics
When the IGMP snooping function is enabled, IGMP information can be checked in
above page.
2.7 STP Statistics
Picture 2.8.1 STP Statistics
In above STP statistics page, users can check the BPDU packets of every port and
every link aggregation STP.
2.8 MAC Address Table
Picture 2.9.1 MAC Address Table
MAC address table and configuration can be checked in above page, users can add
the showed dynamic MAC addresses to static MAC table.

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 16 of 51
Chapter 3 Basic Configuration
3.1 IP Configuration
Picture 3.1.1 IP configuration
The above IP address configuration page can be used to configure the IP address of
device management interface “Interface Vlan 1”. The default IP address, subnet
mask and gateway will be showed in the page. When revise the configuration,
please press “save” to confirm new configuration. Press “reset” to back to original
configuration.
Above configuration need to be done under default “Static” state, if switch the IP
address mode to DHCP, IP address will be get dynamically. Please record the new IP
address for future login.
Notice: Don’t modify the subnet mask unless exceptional case, login problem will be
caused by improper modification.

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 17 of 51
3.2 Account Configuration
Picture 3.2.1 Account configuration
Login password can be revised in this page, please remember the new password for
future login.
3.3 Logging Setting
Picture 3.3.1 Logging Setting
System log configuration is checked in above page. Remote log server can be
configured, system log can be saved on the remote server as backup use. Enable or
disable the remote backup function in this page, “server IP address” need to be
entered manually.

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 18 of 51
3.4 Port Setting
Picture 3.5.1 Port Setting
Port Status: The user can enable or disable a port in this page. Click “Enable” to open
the port, click “Disable” to close the port, the default setting is “Enable”.
Port Mode: 6 modes can be configured: Auto-negotiation,10 Half,10 Full,100 Half, 100
Full and1000 Full. Default mode is Auto-negotiation, can be changed in pull-down list.
Flow Control: This function is defaulted closed, open it when needed.
Loop Detection: The function is defaulted closed, open it when needed. A port will be
blocked to cut the loop when loop is detected.( Notice: the port link indicator in front
panel will be still on when the port is blocked, for the physic connection is existed; while
the link indicator on the top of web management pages will be off.)

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 19 of 51
Chapter 4 Advanced Configuration
4.1 Port Mirror Configuration
Picture 4.1.1 Port Mirror Configuration
Users can do Port Mirror Configuration in above page. Port mirroring is used on
a network switch to send a copy of network packets or data traffic from some ports (or
an entire VLAN) to a network monitoring connection on specified switch port. The
original port is called Source Port, and the specified port is Mirroring Port. This is
commonly used for network appliances that require monitoring of network traffic
without influencing the normal working of every port, it’s a convenient
online-monitoring function.
All ports have mirroring function, but only one port can be configured as Mirroring Port.
In the same system, there is only one mirroring port, while more than one Source Ports
can be existed. When a port is configured as mirroring port, its corresponding port can’t
be configured as source port.

ALL-SG8310PM - User’s Guide
ALLNET GmbH Computersysteme – Alle Rechte vorbehalten
Irrtum und Änderungen vorbehalten
Page 20 of 51
4.2 Port Aggregation
4.2.1 Static Aggregation
Picture 4.2.1 Static Aggregation
Switches support 8 aggregation groups, each group contains maximum 8 ports. The
members in the same aggregation group should have same configuration for port
forwarding rate mode and VLAN distribution.
If LACP function applied for some ports, then static aggregation can’t be
configured.
Notice: Static aggregation can’t be configured when LACP function enabled.
4.2.2 LACP Setting
Picture 4.2.2 LACP Setting
When the LACP protocol is on, the aggregated devices interactively gather information