Allnet ALL8808POE User manual

ALL8808POE
8 Port Gigabit PoE+ Switch
Manual

FCC Certifications
This Equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications.

Operation of this equipment in a residential area is
likely to cause harmful interference in which case the
user will be required to correct the interference at his
own expense.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
this device must accept any interference received;
including interference that may cause undesired
operation.
CE Mark Warning
This equipment complies with the requirements
relating to electromagnetic compatibility, EN 55022
class B for ITE, the essential protection requirement of
Council Directive 89/336/EEC on the approximation of
the laws of the Member States relating to
electromagnetic compatibility.
Company has an on-going policy of upgrading its

products and it may be possible that information in this
document is not up-to-date. Please check with your
local distributors for the latest information. No part of
this document can be copied or reproduced in any
form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of
their respective companies.
Copyright © 2012, All Rights Reserved.

1
Unpacking Information
Thank you for purchasing this product. Before
installation, please verify that your package contains
the following items.
1. One 8-port Gigabit Ethernet with 8-port
PoE+ Desktop Unmanaged Switch
2. 1* AC power cord
3. Rubber feet and screws
4. User’s Manual
5. 2* Brackets
Introduction
General Description
The device is a powerful, high-performance Gigabit
Ethernet Switch, with all 8 ports capable of
10/100/1000Mbps auto-negotiation operation (NWay),
which means the switch could automatically negotiate
with the connected partners on the network speed and
duplex mode. It is ideal for micro-segmenting large

2
networks into smaller, connected subnets for improved
performance, enabling the bandwidth demanding
multimedia and imaging applications. Moreover, the
10/100/1000Mbps auto-sensing ability provides an
easy way to migrate 10/100Mbps to 1000Mbps
network with no pain.
This switch supports PoE, which supplies power for
connected devices via CAT 5 and above twisted
cables. By integrating the data transmitting cable and
power cord, it eliminates the effort constructing your
network. You could easily connect a Wireless AP or a
VoIP phone to this switch without looking outlets for
them. Over current protection and circuit shorting
protection are also supported to ensure the safety.
The switch is plug-n-play without any software to
configure and also fully compliant with all kinds of
network protocols. Moreover, the rich diagnostic LED
indicators on the front-panel provide the operating
status of individual port and whole system.

3
Key Features
Complies with 10BASE-T specifications of the
IEEE802.3 standard
Complies with 100BASE-TX specifications of the
IEEE802.3u standard
Complies with 1000BASE-T specifications of the
IEEE802.3ab standard
Compliant with IEEE 802.3af/at PoE standard
(DTE power via MDI)
Provides 8 PoE ports with classification identify
Supports 31.5W maximum per PoE port
Supports over current protection and circuit
shorting protection
8 * RJ-45 ports for 100BASE-TX and 1000
BASE-T and 10BASE-T connectivity

4
Provide 8* 10/100Mbps auto-detect（half/full）and
1000Mbs full duplex switch ports (IEEE802.3/
802.3u/ 802.3ab)
Supports MDI/MDI-X auto crossover
Supports 136W Max;
Full load: 31.5W(at) x 4P + 5W = 131W ;
15.4W(af) x 8P + 5W = 128.2W
Wire-speed packet filtering and forwarding rate
Store-and-forward architecture filters fragment &
CRC error packets
Supports extensive LED indicators for network
diagnostics
Internal universal switching power supply

5
The Front Panel
The front panel consists of LED indicators and the
ports. For detailed LED definition, please refer to the
next paragraph.
The front panel of the switch is shown as below:
LED Definition
The switch contain 1* power LED and 1* loop LED for
the device, 1* PoE LED for each port and 1* Link/Act
LED for each port.
LED indicators for the device
The switch provides a power LED and a loop LED for
the device.

6
LED
Status
Operation
Power
Steady Green
The switch is powered on
Off
The switch is powered off
Loop
Blinking Red
There is a loop existing
Off
There is no loop existing
Port LED
The switch provides one “Link/ACT” LED and
one PoE LED for each port.
LED
Status
Operation
Link/
ACT
Steady Green
Valid port connection
Blinking Green
Valid port connection and
there is data transmitting/
receiving
Off
Port disconnected
PoE
Green
One PoE compliant device is
connecting with this port.
Off
There is no PoE compliant
device connecting with this
port.
The Rear Panel