Altinex TNP328 Series User manual

TNP328 INTERCONNECT BOX User’s Guide
400-0611-002
1
Welcome!
We greatly appreciate your purchase of your TNP328 Series
Tilt 'N Plug. We are sure you will find it reliable and simple to
use. Superior performance for the right price, backed by solid
technical and customer support is what ALTINEX has to offer.
We are committed to providing Signal Management Solutions®
to our customers for the most demanding audiovisual
installations at competitive pricing and we welcome you to join
the ranks of our many satisfied customers throughout the
world.
1. Precautions and Safety Warnings
Please read this manual carefully before using your Tilt 'N
Plug. Interconnect Box. Keep this manual handy for future
reference. These safety instructions are to ensure the long life
of your Tilt 'N Plug. and to prevent fire and shock hazards.
Please read them carefully and heed all warnings.
1.1 General
Unauthorized personnel shall not open the unit as there
are high-voltage components inside. Qualified ALTINEX
service personnel or their authorized representatives must
perform all service.
1.2 Installation Precautions
For best results, place the Tilt 'N Plug in a dry area away
from dust.
To prevent fire or shock, do not expose this unit to water
or moisture. Do not place the unit in direct sunlight, near
heaters or heat-radiating appliances, or near any liquid.
Exposure to direct sunlight, smoke, or steam can harm
internal components.
Handle carefully; dropping or jarring can damage the
bezel.
Never place fingers inside the opening on either side of
the unit. This action could cause injury due to sharp edges
inside.
Do not place heavy objects on top of the Tilt 'N Plug. Do
not use excessive force to push down on the top of the
unit.
Disconnect the power cord to turn off the power. This
supplies power to the socket on the pop-up panel. The
power outlet should be installed near the equipment and
be easily accessible.
We recommend using wall outlets with a Ground Fault
Circuit Interrupter (GFCI) for maximum protection.
Install all cables according to the instructions found herein.
Do not force or pull any cable that is attached to the Tilt 'N
Plug.
1.3 Cleaning
Surfaces should be cleaned with a dry cloth. Never use
strong detergents or solvents such as alcohol or thinner.
Do not use a wet cloth or water to clean the unit.
2. Installation Procedures
Step 1 Cut an opening into the table’s surface. Refer to the ALTINEX website at
www.altinex.com for table cutout requirements.
NOTE: The table can be 2.25 in (57 mm) or less in thickness. Always confirm dimensions before
cutting to insure that specifications have not changed.
Step 2 Insert the TNP328 into the table cutout.
Step 3 Place the support brackets under the table and place them between the support mount
grooves on the side of the unit. Attach the brackets to the groove at the desired height
and secure them to the bottom of the table using the knurled table securing screws
provided with the additional wing nuts for added tightening. See Diagram 3 for details.
Step 4 To lower the unit, push on the top cover until it locks into place.
Step 5 Secure all cables to the underside of the table using the cable clamps and screws
included with the TNP. Pass the power cord from the bottom of the housing and attach it
to the table separate from the signal cables. Leave enough slack in the service loop to
allow for easy opening and closing, but not too much as to cause excess drooping of the service loop.
Step 6 Connect the appropriate cables with the correct input connectors on the bottom of the unit.
Step 7 Once you have applied power and connected the proper cables on the bottom of the unit you may raise the unit. To raise the
unit into position, push down on the front of the top cover; the latching mechanism will then release, allowing the pneumatic
spring to raise it into position.
NOTE: It may be necessary to adjust the service loop of the cables for optimal performance.
3. Limited Warranty/Return Policies
Please see the ALTINEX website at www.altinex.com for details on warranty and return policies.

TNP328 User’s Guide
400-0611-002
2
4. Technical Specification
Specifications are subject to change. Please visit http://www.altinex.com for up-to-date specification
Features/Description
TNP328/320C*
Pass-Through AC Power 9ft. (3.0 m)
120 VAC,60 Hz, 12A
NEMA Socket-Plug
Agency Approval
UL/C-UL Listed
File E254082
Audio, Video,
Communication
6 ft. (2 m)
Computer video
15-pin HD F-M (1)
Computer Audio
3.5mm F-M (1)
HDMI
**HDMI F-M (1)
Network
CAT-6 (RJ-45) F-M (1)
Accessories Included
Hardware
-Mounting screws/brackets
-Cable clamps/screws
Table 1 TNP328 General Specifications
Mechanical
Max. Table Thickness
2.25 in (57 mm)
Height, opened
6.4 in (163 mm)
Width
5.7 in (145 mm)
Depth
5.2 in (132 mm)
Finish Standard:
Models ending in S:
Matt Black Finish
Brushed Aluminum
Weight (approx.)
2.75 lb. (1.25 kg)
Shipping Weight
5.5 lb. (2.5 kg)
TOperating
10C - 35C
TMaximum
40C
Humidity
90non-condensing
Table 2 TNP328 Mechanical Specifications ***
Electrical
(Dual Outlet Panel)
TNP328
Power Rating
(pass-through AC power)
120VAC,60Hz,
Up to 12A total
Table 3 TNP328 Electrical Specifications ***
* Models ending in “C” are customizable.
Models ending in “S” have brushed aluminum finish.
** HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in
the United States and other countries.
*** Dimensions and ratings include the customizable “C” models and “S” models.

TNP328 User’s Guide
400-0611-002
3
5. The TNP328 Interconnect Box
Available in high quality matte black finish or clear brushed
finish
Pre-configured, compact hybrid interconnect solution with
HDMI and VGA interconnects or factory configured as a
TNP320C
Dual AC sockets rated for up to 12A from one power cord
Simple, drop-in installation
Gas spring for smooth operation
UL listed
The TNP328 is a compact interconnect solution designed for mounting into tables, podiums, or other furniture as part of a presentation
system. Inputs are accessed by pushing down on the top cover allowing the unit to tilt open. The inputs are hidden by pressing down on
the top cover until the latching mechanism engages. In the closed position, the top cover lays almost flush with the tabletop. This
tabletop solution offers up to dual 12 Amps from the AC sockets with computer video/audio, HDMI and network pass through cables.
The passive cables are 6ft and are bundled together for organized cable management. The power cable is split to deliver power to both
outlets on the tabletop from one AC plug. The TNP328 is one of many solutions available in the TNP Jr product line that can be
customized with many different connectivity options as a TNP320C.

TNP328 User’s Guide
400-0611-002
4
6. Application Diagrams
Diagram 1: Typical Setup and use of a TNP328
Diagram 2: Front View

TNP328 User’s Guide
400-0611-002
5
Diagram 3: Mounting the TNP328
Diagram 4: Side Dimensions
Diagram 5: Top Bezel Dimensions

TNP328 User’s Guide
400-0611-002
6
7. Operation
7.1 Opening and Closing the Tilt 'N Plug
The Tilt 'N Plug will open easily when the top is pressed down
and then released.
When the Tilt 'N Plug is not in use, simply press the top down
until it is level with the surface of the table and then release. The
unit will remain hidden until needed again.
7.2 Power/Signal Connections
Connect external devices to the appropriate connector on the Tilt
'N Plug. Remember, the devices plugged into the AC power
connectors should not draw more than 12A total.
8. Troubleshooting Guide
The Tilt 'N Plug supplied was carefully tested and no problems were detected. However, we would like to offer the following
suggestions:
TNP
Symptom
Resolution
Signal quality is poor.
1. Please make sure that the highest quality video and network cables are used.
2. The TNP is a passive unit and does not alter signals in any way. If there is suspected problem
with the signal quality, check the quality of the cables coming into and the TNP and connecting
to the output of the TNP. If they are of low quality or improperly assembled, this will affect the
overall quality of the signal.
Damaged power cord
1. Make sure that no cable or power cord is damaged or pinched.
2. If there has been damage, do not use the Tilt 'N Plug. Please call the ALTINEX Customer
Service Department at [phone] to have the unit repaired.
Unit raises too slowly
1. If the unit does not rise into position correctly, check the service loops for the signal and power
cords on the bottom of the unit. If the service loop is too small the cables will counteract the
spring trying to raise the unit into position.
Unit tilts up too fast
1. If the unit rises into position too fast, check the service loops for the signal and power cords on
the bottom of the unit. If the service loop is too large and the cables are putting upward pressure
on the unit, the unit will tilt up too fast.
Unit does not close all
the way
1. If the unit does not close flush with the bezel, check the service loops for the signal and power
cords on the bottom of the unit. If the service loop is putting upward pressure in the unit, the unit
will not be able to seat all the way down.