Altinex TP315-105 User manual

TP315-105 HDMI OVER ANYWIRE TRANSMITTER (DC) User’s Guide
400-0678-001
Welcome!
Everyone at Altinex greatly appreciates your purchase of the
TP315-105. We are confident that you will find it to be reliable and
simple to use. If you need support, please do not hesitate to call
us at 714-990-2300.
At Altinex, we are committed to developing unique and state of
the art Signal Management Solutions®for demanding audiovisual
installations. Welcome to the Altinex family of satisfied customers
around the world!
1. Precautions and Safety Warnings
Please read this manual entirely before using your
TP315-105. You can download a full version of this
manual at www.altinex.com. These instructions are to
ensure the reliable operation of your switcher and to
prevent fire and shock hazards. Please read them
carefully and heed all warnings.
1.1 General
Qualified Altinex service personnel or their authorized
representatives must perform all service.
1.2 Installation Precautions
To prevent fire or shock, do not expose this unit to water
or moisture. Do not place the TP315-105 in direct sunlight,
near heaters or heat-radiating appliances, or near any
liquid. Exposure to direct sunlight, smoke, or steam can
harm internal components.
Handle the TP315-105 carefully. Dropping or jarring can
cause damage.
Do not pull any cables attached to the TP315-105.
1.3 Cleaning
Clean the TP315-105 with a dry cloth only. Never use
strong detergents or solvents such as alcohol or thinner.
1.4 FCC Notice
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 2 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions found herein, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at their own expense.
Any changes or modifications to the unit not expressly
approved by Altinex, Inc. could void the user’s authority to
operate the equipment.
2. Installation Procedures
Note: Download and read the entire online manual to become familiar with the
TP315-105 and for detailed installation instructions, including multiple receiver
wiring.
Step 1: Connect the TP315-105 Transmitter to the TP315-102/106 Receiver using any
2 wires or 2-conductor cable. For best results, use 24 to 12 gage wire; the
12-gage limitation is due to the opening in the terminal
connector.
The terminals are red and black, but there is no polarity.
Connect either wire to either terminal.
Step 2: Connect the TP315-105 to power using the adapter provided.
Step 3: Connect the source HDMI video (computer, Blu-ray, videoconference, etc.) to the HDMI input on the TP315-105 using the
HDMI cable provided.
Step 4. The AnyWire transmitter is now operating. Once the receiver is detected, video is displayed automatically.
Step 5. A display may be connected to the HDMI output on the TP315-105 for use as a local display.
Step 6. The AnyWire Transmitter/Receiver pair allows IR pass-through from the receiver (far side) to the transmitter (near side). An IR
emitter is included with the TP315-105 and may be connected to the HDMI source allowing control from a remote control
connected to the receiver on the far side of the AnyWire installation. The AnyWire receiver includes an IR receiver.
3. Warranty and Return Policies
Please visit the Altinex website at www.altinex.com for details on warranty and return policies. In the case of a unit needing repair,
please complete a RMA (return material authorization) form by clicking the Warranty link located on the bottom of the Altinex
homepage. Once completed, please email the form to [email protected].

TP315-105 User’s Guide
400-0678-001 2
4. Technical Specifications
Specifications are subject to change due to design improvements. Please see www.altinex.com for up to date information.
Features/Description
TP315-105
Input Connectors
Digital Video + Audio
HDMI F, Type A (1)
DC Power
2.5 mm CP (1)
Output Connectors
Digital Video + Audio
HDMI F, Type A (1)
AnyWire Video
Terminal Post F (2)
IR (from receiver side)
3.5 mm Audio F (1)
Compatibility
Signal types
HDMI
Signal resolutions
720p, 1080i, and 1080p
Accessories Included
HDMI Cable
n/a
IR Emitter
n/a
Power Adapter
+9VDC, 1.1 A (PS5506US)
Table 1. TP315-105 General
Mechanical
TP315-105
Material
Aluminum
Color
Black
Height
1.05 in (27 mm)
Width
6.73 in (171 mm)
Depth
3.51 in (89 mm)
Weight
1.0 lbs. (0.45 kg)
T° Operating
10°C-45°C
Humidity
90% non-condensing
MTBF (calc.)
38,000 hrs.
Table 2. TP315-105 Mechanical
Electrical
TP315-105
Video Input Signals
Digital Video + Audio
HDMI Standard
Video Output Signals
Digital Video + Audio
AnyWire
Power Consumption
External Adapter: +9 VDC
600 mA (5.4 W)
Table 3. TP315-105 Electrical

TP315-105 User’s Guide
400-0678-001 3
5. About Your TP315-105
HDMI over 2-conductor cable
Automatic input/receiver detection
HDMI resolutions 720p, 1080i, and 1080p
Transmission up to 300 m
IR pass-through control
Local monitor output
The TP315-105 HDMI over AnyWire transmitter allows the transmission of 1080P HDMI signals up to 300 m using a simple
2-conductor cable. A single transmitter may drive up to 4 receivers using either 4 individual wire pairs over 300 m each, or by daisy
chaining the receivers. The only restriction being the wire pair from the transmitter to each receiver cannot be bundled together as
crosstalk will occur.
The TP315-105 is an economical solution for many audiovisual installations. The 2-wire solution makes installation easy without the
need to cut and splice wires and install expensive connectors or purchase costly cables. Simply route your wires, cut and trim the
installation and connect to the terminals. That's it!
The unique design of the AnyWire Transmitter provides stable video transmission over greater distances than other designs. IR
pass-through for receiver side to transmitter side control is provided without corrupting the HDMI signal during transmission of IR
signals.
Operation does not require any user control or interaction. Simply connect the HDMI input and the transmitter scans for the receiver
and when detected automatically pairs to the receiver and begins video transmission.
A local video output is provided to support a local monitor. The local monitor allows the user on the transmitter side to know what is
being presented on the far side of the installation.

TP315-105 User’s Guide
400-0678-001 4
6. Application Diagrams
Diagram 1: Typical Setup

TP315-105 User’s Guide
400-0678-001 5
Diagram 2: Internal View

TP315-105 User’s Guide
400-0678-001 6
Diagram 3: Dimensions

TP315-105 User’s Guide
400-0678-001 7
Diagram 4: Multiple Receiver Setup

TP315-105 User’s Guide
400-0678-001 8
7. Operation
The TP315-105 requires no adjustments for performance.
Once set-up, the TP315-105 AnyWire Transmitter will work
trouble-free without user intervention.
7.1 Reset Button
A reset button is provided on the side of the unit to allow a
forced reset without having to disconnect power. Use this only
if there are problems connecting to the receiver; typically after
a new display is installed or after a power outage.
8. Troubleshooting Guide
We have carefully tested and have found no problems in the supplied TP315-105. However, we would like to offer suggestions for the
following:
AnyWire
Symptom
Resolution
LEDs on Are Off
The unit may not be receiving power.
1. Make sure the power adapter is plugged into a working AC outlet.
2. Use only the power adapter provided.
3. The Connected LED should be on and green.
Data Transmission
LED is flashing very
slow
The transmitter and receiver are not communicating.
1. Check the 2 wire connection; make sure both wires are connected.
2. Make sure the receiver is powered on.
3. Press the reset button on the side of the unit or reset power to force the transmitter to try and
re-establish a connection.
No Display
The HDMI input signal may be missing.
1. Check the source and make sure there is a signal present.
2. Make sure the source resolution is set to 720p, 1080i, or 1080p.
3. Make sure both the TP315-105 and TP315-102/106 are powered and the Connected LEDs are
both green.
4. Make sure the monitor has power and is turned on.
5. Verify the monitor is connected to the TP315-102/106 Receiver's HDMI output
6. Make sure the monitor's correct HDMI input number is selected.
Poor Output Image
1. The source resolution may not be compatible with the projector or other display device. Try
other resolutions from the source.
2. The source and display may not be compatible. Connect the source directly to the input of the
projector or other display device. If the image is poor the devices may be incompatible.
3. If using multiple receivers, make sure that the transmission lines are not bundled together at any
point in the transmission. If the cables are bundled (zip tied together) this causes crosstalk
between the different channels and can result in image problems.