Alto-Shaam 100-HW/D4 Owner's manual

p r i n t e d i n u.s.a.
W164 N9221 Water Street • P.O. Box 450
Menomonee Falls, Wisconsin 53052-0450 U.S.A.
PHONE: [phone] • 800.558.8744 U.S.A. / CANADA
FAX: [phone] • 800.329.8744 U.S.A. ONLY
www.alto-shaam.com
Consult instructions
for operation and use.
Hot Food Holding
Drop-In Wells
Electric
500-HWI/D4



odels:
100-HW/D4/D6/D443/D643
 
200-HW/D4/D6/D443/D643
 
200-HWI/D4/D6/D443/D643
 
 
300-HW/D4/D6/D443/D643
 
300-HWI/D4/D6/D443/D643
 
 
400-HW/D4/D6
 
400-HWI/D4/D6
 
500-HW/D4/D6
 
500-HWI/D4/D6
 
400-HW/D4
300-HWI/D6
100-HW/D6
MN-37234 (rev. 3) • 06/16
200-HWIS/D6

MN-37234 (Rev. 3) 06/16 • Hot Food Drop-In Well
Delivery ....................................1
Unpacking..................................1
Unpacking Safety Procedures and Precautions ......2
Installation
Installation Requirements ....................4
Clearance Requirements.....................4
Options and Accessories ....................4
Weights and Capacities .....................5
Dimensions...............................6
Rough Cut Openings ......................18
Locking Kit Installation .....................18
Remote Control Mounting Instructions .........19
Undermount Kit Installation .................20
Electrical Connection ......................24
Electrical Specifications ....................25
Operation
Operating Instructions .....................26
General Holding Guidelines .................27
Care and Cleaning
Cleaning and Preventative Maintenance ........28
Food Safety .............................30
Service
100-HW ................................31
200-HW ................................33
200-HWI, 200-HWIS .......................35
300-HW ................................38
300-HWI, 300-HWIS .......................40
400-HW ................................43
400-HWI ................................45
500-HW ................................47
500-HWI ................................49
Wire Diagrams
Always refer to the wire diagram(s) included with the
appliance for most current version.
Warranty
Transportation Damage and Claims ... Back Cover
Limited Warranty ................. Back Cover

MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 1
Delivery
This Alto-Shaam appliance has been thoroughly
tested and inspected to ensure only the highest
quality unit is provided. Upon receipt, check for any
possible shipping damage and report it at once to the
delivering carrier. See Transportation Damage and
Claims section located in this manual.
This appliance, complete with unattached items
and accessories, may be delivered in one or more
packages. Ensure all standard items and options
have been received with each model as ordered.
Save all the information packed with the appliance.
Register online at www.alto-shaam.com to ensure
prompt service in the event of a warranty parts and
labor claim.
This manual must be read and understood by all
people using or installing the equipment model.
Contact the Alto-Shaam Tech Team Service
Department if you have any questions concerning
installation, operation, or maintenance.
1-800-558-8744; [email protected]
Unpacking
• Carefully remove the appliance
from the carton or crate.
NOTICE: Do not discard the
carton and other
packaging material
until you have
inspected the unit
for hidden damage
and tested it for
proper operation.
• Read all instructions in this manual carefully
before installing this appliance, using the appliance
or performing routine maintenance. Following
procedures other than those indicated in this
guide to use and clean the appliance is considered
inappropriate and may cause damage, injury or
fatal accidents, in addition to invalidating the
guarantee and relieving Alto-Shaam of all liability.
• DO NOT DISCARD THIS MANUAL.
This manual is considered part of the appliance
and is provided for the owner or manager of the
business and for training personnel. Additional
manuals are available from the Alto-Shaam
Tech Team Service Department.
• Remove all protective plastic film, packaging
materials, and accessories from the appliance
before connecting electrical power. Store any
accessories in a convenient place for future use.
®
®
WARNING
Appliance and accessories may be
heavy. To prevent serious injury, always
use a suicient number of trained and
experienced workers when moving or
leveling appliance and handling accessories.

• Operational Environmental Conditions
• Unit must acclimate to room temperature in the
environment it is placed. 24 hours is recommended.
• Ambient temperature range of 60°F to 110°F (16°C to 43°
C).
• Relative humidity of less than 95% non-condensation.
• Atmospheric pressure range of 50KPa to 106KPa.
Serial number is required for all inquiries.
Always include both model and serial number(s) in any
correspondence regarding the appliance.
Model: ______________________________________________
Serial Number: ______________________________________________
Purchased From: ______________________________________________
Date Installed: ____________________ Voltage: _____________
Delivery Unpacking

MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 2

Used to indicate the presence of a hazard that
can or will cause minor personal injury, property
damage, or a potential unsafe practice if the
warning included with this symbol is ignored.

Used to indicate the presence of a
hazard that can or will cause minor or
moderate personal injury or property
damage if the warning included with
this symbol is ignored.

Used to indicate the presence of
a hazard that WILL cause severe
personal injury, death, or substantial
property damage if the warning
included with this symbol is ignored.

Used to indicate the presence of
a hazard that CAN cause personal
injury, possible death, or major
property damage if the warning
included with this symbol is ignored.
• This appliance is intended to cook, hold or process
foods for the purpose of human consumption. No
other use for this appliance is authorized and is
therefore considered dangerous. The appliance
must not be used to cook food containing flammable
materials (such as food with alcohol). Substances
with a low flash point can ignite spontaneously and
cause a fire.
• This appliance is intended for use in commercial
establishments where all operators are familiar with
the purpose, limitations, and associated hazards of
this appliance. Operating instructions and warnings
must be read and understood by all operators and
users. We recommend regular training of your
staff to avoid the risk of accident or damage to the
unit. Operators must also receive regular safety
instructions.
• Any trouble shooting guides, component views, and
parts lists included in this manual are for general
reference only and are intended for use by qualified
and trained technicians.
• This manual should be considered a permanent
part of this appliance. This manual and all supplied
instructions, diagrams, schematics, parts lists,
notices, and labels must remain with the appliance
if the item is sold or moved to another location.
NOTICE: Used to notify personnel of
installation, operation, or
maintenance information that is
important but not hazard related.


Knowledge of proper procedures is essential to the
safe operation of electrically and/or gas energized
equipment. The following hazard signal words and
symbols may be used throughout this manual.
Used to indicate that referral to
operating instructions is a mandatory
action. If not followed the operator
could suffer personal injury.
Used to indicate that referral to
operating instructions is recommended
to understand operation of equipment.
NOTICE: For equipment delivered for use in
any location regulated by the
following directive: 2012/95/EC WEEE
DO NOT dispose of electrical or
electronic equipment with other
municipal waste.
Unpacking Safety Procedures and Precautions

MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 3
• To prevent serious injury, death or property
damage, your appliance should be inspected and
serviced at least every twelve (12) months by an
authorized service partner or trained technician.
• ONLY allow an authorized service partner or
trained technician to service or to repair your
appliance. Installation or repairs that are not
performed by an authorized service partner or
trained technician, or the use of non-factory
authorized parts will void the warranty and relieve
Alto-Shaam of all liability.
• When working on this appliance, observe
precautions in the literature, on tags, on labels
attached to or shipped with the appliance and other
safety precautions that may apply.
• If the appliance is installed on casters freedom of
movement of the appliance must be restricted so
that utility connections (including gas, water, and
electricity) cannot be damaged when the unit is
moved. If the appliance is moved, make sure that all
utility connections are properly disconnected. If the
unit is returned to its original position, make sure
that any retention devices and utility connections
are properly connected.
• ONLY use the appliance when it is stationary.
Mobile oven racks, mobile plate racks, transport
trolleys, and appliances on casters can tip over
when being moved over an uneven floor or
threshold and cause serious injury.
• ALWAYS apply caster brakes on mobile appliances
or accessories when these are not being moved.
These items could move or roll on uneven floors
and cause property damage or serious injury.
• Be extremely careful when moving appliances
because the food trays may contain hot fluids that
may spill, causing serious injury.
• ALWAYS open the appliance door very slowly.
Escaping hot vapors or steam can cause serious
injury or death.


• If your gas appliance is installed under an
exhaust hood, the hood must be switched ON
when the oven is in use to avoid the build up of
combustion gases. Failure to do so may result in
serious injury, death or property damage.
•
NEVER place objects near the oven exhaust vents.
This area is hot and could be a potential ignition
source for a fire.
• Do not allow objects to block or obstruct the area
below the oven base. This may result in fire,
damage to the equipment or serious injury.
• Do not use the attached hand-held hose to spray
anything other than the interior of the oven
compartment.
• Do not use the attached hand-held hose on the
surface of a hot cooking compartment. The
sudden temperature change can damage the oven
interior. Allow the oven to cool to a minimum of
150°F (66°C). Failure to observe this precaution
can void the warranty.
WARNING
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
concerning use of the appliance by person
responsible for their safety.
Children should be supervised to ensure
that they do not play with the appliance.

MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 4


The Alto-Shaam
hot well must
be installed in
a location that
will permit it
to function for its
intended purpose and to
allow adequate clearance for
ventilation, proper cleaning,
and maintenance access.
1. The hot well must be installed on a stable and level
surface free of vibration and suitably strong enough to
support the combined weights of the appliance plus the
maximum product load weight.
2. DO NOT install this appliance in any area where it may
be affected by any adverse conditions such as steam,
grease, dripping water, high temperatures, or any other
severely adverse conditions.
3. DO NOT store or use any flammable liquids or allow
flammable vapors in the vicinity of this oven or any
other appliance.
4. This appliance must be kept free and clear of any
combustible materials.
5. Countertop material must withstand temperature up to
200°F (93°C). Verify countertop material temperature
rating with manufacturer before installing to ensure
counter can withstand heat.
6. A stainless steel heat shield is recommended if the area
under the appliance is used for storage.
7. To maintain proper food temperature, overhead heating
is required.

The hot well
should be leveled before the electrical
supply is connected. Level the appliance from side-to-
side and front-to-back with the use of a spirit level. For
appliances installed on a mobile stand, it is important that
the floor surface be level due to the probability of frequent
repositioning.
NOTICE: It is important to apply a food grade silicone
underneath the decor flange to seal flange to the
countertop.
WARNING
Improper installation, alteration,
adjustment, service, cleaning, or
maintenance could result in PROPERTY
DAMAGE, SEVERE INJURY, or DEATH.
Read and understand the installation,
operating and maintenance instructions
thoroughly before installing, servicing, or
operating this equipment.
WARNING
Appliance and accessories may be
heavy. To prevent serious injury, always
use a suicient number of trained and
experienced workers when moving or
leveling appliance and handling accessories.
WARNING
For your safety
DO NOT store or use gasoline or other
flammable vapors or liquids in the vicinity
of this or any other appliance.
CAUTION
To prevent SEVERE PERSONAL INJURY or
PROPERTY DAMAGE:
ALWAYS use hand protection when
operating this appliance to avoid burns.
Metal parts of this equipment become
extremely hot when in operation.

Pan Divider Bars
Full Size (HW, HWLF) 16019
Half Size / Third-Size 11318
Extra Long (200 and 300-HW/d443 or d643) 1012405
Locking Kit 5020849
Undermount Kit (100-HW only) 5020793
®

1" (25mm) from combustible surfaces
Installation Installation Requirements Leveling Clearance Requirements Options & Accessories

MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 5
Options & Accessories
installation

Hot Well Net Weights

 D4 D6 D443 D643
100-HW 25 lb (11 kg) 29 lb (13 kg) 31 lb (14 kg) 35 lb (16 kg)
100-HWLF 27 lb (12 kg) 31 lb (14 kg) — —
200-HW 40 lb (18 kg) 45.5 lb (21 kg) 50 lb (23 kg) 56 lb (25 kg)
200-HWLF 43 lb (20 kg) 48 lb (22 kg) — —
200-HWI 50 lb (23 kg) 56.25 lb (26 kg) 62 lb (28 kg) 69.5 lb (32 kg)
200-HWILF 54.25 lb (25 kg) 60.5 lb (27 kg) — —
200-HWIS —56.25 lb (26 kg) — —
300-HW 54.5 lb (25 kg) 61 lb (28 kg) 68 lb (31 kg) 75 lb (34 kg)
300-HWLF 58 lb (26 kg) 64.5 lb (29 kg) — —
300-HWI 69 lb (31 kg) 77.5 lb (35 kg) 85 lb (39 kg) 99 lb (45 kg)
300-HWILF 74 lb (34 kg) 83 lb (38 kg) — —
300-HWIS —77.5 lb (35 kg) — —
400-HW 71 lb (32 kg) 79 lb (36 kg) — —
400-HWLF 75 lb (34 kg) 83 lb (38 kg) — —
400-HWI 90 lb (41 kg) 101.5 lb (46 kg) — —
400-HWILF 96.5 lb (44 kg) 108 lb (49 kg) — —
500-HW 85 lb (39 kg) 94.5 lb (43 kg) — —
500-HWLF 89.5 lb (41 kg) 100 lb (45 kg) — —
500-HWI 107 lb (49 kg) 121 lb (55 kg) — —
500-HWILF 115 lb (52 kg) 128.5 lb (58 kg) — —
Model Max. Capacity Max. Volume
Full-Size Pans*
12" x 20" x 4"
GN 1/1
(530 x 325 x 100mm)
Half-Size Pans*
12" x 10" x 4"
GN 1/2
(265 x 325 x 100mm)
Third-Size Pans*
12" x 6" x 4"
GN 1/3
(176 x 325 x 100mm)
D4 D443 D6 D4 D443 D6 D4, D6 D443
100 Series 24 lb
(11 kg)
32 lb
(15 kg)
36 lb
(16 kg)
14.5 qt
(14 L)
19.2 qt
(18 L)
22 qt
(21 L) 1 2 34
200 Series 48 lb
(22 kg)
64 lb
(29 kg)
72 lb
(33 kg)
29 qt
(28 L)
37.8 qt
(36 L)
44 qt
(42 L) 2 4 6 8
300 Series 72 lb
(33 kg)
96 lb
(44 kg)
108 lb
(49 kg)
43.5 qt
(42 L)
56.6 qt
(53 L)
66 qt
(63 L) 36 9 12
400 Series 96 lb
(44 kg) —144 lb
(65 kg)
58 qt
(56 L) —88 qt
(84 L) 4812 —
500 Series 120 lb
(54 kg) —180 lb
(82 kg)
72.5 qt
(70 L) —110 qt
(105 L) 5 10 15 —
*based on 4" deep pans. Will also accept 2-1/2" (65mm)deep pans; d6 appliances Will accept 6" (150mm) deep pans

MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 6
installation
23-1/8" (586mm)
2-3/16" (71mm)
1-1/2"
(37mm) 1-9/16"
(39mm)
20-3/16" (512mm)
WELL
7-1/2"
(190mm)
15" (380mm)
12" (304mm)
WELL
5"
(126mm)
6-15/16" (175mm)
5" (127mm)
100-HW/D443100-HW/D4
6-5/16" (159mm)
5-9/16" (140mm)
4-3/8" (111mm)
WELL
2-5/8" (67mm)
27-1/4" (691mm)
WELL
29-1/16" (738mm)
9/16" (14mm)
FLANGE
2-1/4" (57mm)
22-1/16" (559mm)
9/16" (14mm)
FLANGE
20-3/16" (512mm)
WELL
7" (177mm)
5-9/16" (140mm)
4-3/8" (111mm)
WELL
30-3/16" (765mm)
2-13/16" (71mm)
1-1/2"
(37mm)
27-1/4" (691mm)
WELL
7-1/2"
(190mm)
1-9/16"
(39mm)
15" (381mm)
12" (304mm)
WELL
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)
13-5/8" (345mm)
3/4" (18mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
Ø 1/4" (5mm)
6-15/16"
(175mm)
6-7/16"
(163mm)
2-1/2" (62mm)
4-15/16" (125mm)
27-1/16" (686mm)
4-3/4" (121mm)
3-7/16"
(87mm)
20-3/16" (512mm)
WELL
9-3/16" (233mm)
6-15/16" (175mm)
5" (127mm)
5"
(126mm)
3-3/16"
(81mm)
18-5/16" (465mm)
12" (304mm)
WELL
100-HWLF/D4
7" (177mm)
5-9/16" (140mm)
4-3/8" (111mm)
WELL
20-3/16" (512mm)
WELL
22-1/16" (559mm)
2-1/2" (63mm)
FLANGE
2-1/4" (57mm)
Ø 1/4" (5mm)
6-15/16"
(175mm)
6-7/16"
(163mm)
2-1/2" (62mm)
4-15/16" (125mm)
13-5/8" (345mm)
2-3/8" (60mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)

Dimensions
100-HW


MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 7
installation

1-9/16"
(39mm)
23-1/8" (586mm)
20-3/16" (512mm)
WELL
1-1/2" (38mm)
6-15/16" (175mm)
5" (127mm)
5"
(126mm)
28-1/16" (712mm)
25" (635mm)
WELL
200-HW/D4
1-9/16"
(39mm)
28-1/16" (712mm)
25" (635mm)
WELL
30-3/16" (765mm)
27-1/4" (691mm)
WELL
1-1/2" (38mm)
1-7/8" (46mm)
4-1/8" (104mm)
27-1/4" (691mm)
WELL
29-1/16" (738mm)
9/16" (14mm) FLANGE
4-3/8" (111mm)
WELL
200-HW/D443
7-5/16" (185mm)
5-9/16" (140mm)
26-5/8" (676mm)
3/4" (19mm)
FLANGE
3/4" (19mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
20-3/16" (512mm)
WELL
22-1/16" (559mm)
4-3/8" (111mm)
WELL
7-5/16" (185mm)
5-9/16" (140mm)
1-7/8" (46mm)
4-1/8" (104mm)
9/16" (14mm) FLANGE
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16"
(125mm)
4"
(102mm)
Ø 3/16"
(5mm)
6-15/16"
(175mm)
6-7/16"
(163mm)
2-1/2"
(63mm)
4-15/16"
(125mm)
1/4" (6mm)
3-3/16"
(81mm)
31-3/8" (796mm)
25" (635mm)
WELL
27-1/16" (686mm)
20-3/16" (512mm)
WELL
3-7/16" (87mm)
6-15/16" (175mm)
5" (127mm)
5"
(126mm)
26-5/8" (676mm)
2-7/16" (60mm)
FLANGE
2-7/16" (60mm)
FLANGE
7-5/16" (185mm)
5-9/16" (141mm)
20-3/16" (512mm)
WELL
22-1/16" (559mm)
2-1/2" (63mm)
FLANGE
4-3/8" (111mm)
WELL
1-7/8" (46mm)
4-1/8" (104mm)
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)
6-15/16" (175mm)
6-7/16" (163mm)
1/4" (6mm)
Ø 3/16" (5mm)
4-15/16" (125mm)
2-1/2" (63mm)
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
200-HWLF/D4
200-HW


MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 8
26-5/8" (676mm)
9/16" (14mm)
FLANGE
10-7/16" (264mm)
9-15/16" (252mm)
1/4" (6mm)
Ø 3/16" (5mm)
4-15/16" (125mm)
2-1/2" (63mm)
23-3/16" (588mm)
20-3/16" (512mm)
WELL
1-5/16" (33mm)
27-5/8" (701mm)
12" (305mm)
WELL
10-7/16" (264mm)
WATERTIGHT
CONDUIT
8-1/2" (216mm)
5"
(126mm)
200-HWI/D4
7-5/16" (185mm)
5-9/16" (141mm)
20-3/16" (512mm)
WELL
22-1/16" (559mm)
5/8" (16mm)
FLANGE
1-7/8" (46mm)
4-1/8" (104mm)
4-3/8" (111mm)
WELL
1-1/2"
(38mm) WATERTIGHT
CONDUIT
5"
(126mm)
1-5/16" (33mm)
27-5/8" (701mm)
12" (305mm)
WELL
30-1/4" (767mm)
27-1/4" (691mm)
WELL
10-7/16" (264mm)
8-1/2" (216mm)
200-HWI/D443
1-7/8" (46mm)
4-1/8" (104mm)
27-1/4" (691mm)
WELL
29-1/16" (738mm)
5/8" (16mm)
FLANGE
4-3/8" (111mm)
WELL
7-5/16" (185mm)
5-9/16" (141mm)
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)
installation
4-15/16" (125mm)
2-1/2" (63mm)
10-7/16" (264mm)
9-15/16" (252mm)
1/4" (6mm)
Ø 3/16" (5mm)
200-HWILF/D4
7-5/16" (185mm)
5-9/16" (141mm)
20-3/16" (512mm)
WELL
22-1/16" (559mm)
2-1/2" (63mm)
FLANGE
1-7/8" (46mm)4-1/8" (104mm)
3-1/8" (79mm)
31-1/4" (792mm)
12" (305mm)
WELL
27-1/16" (686mm)
20-3/16" (512mm)
WELL
10-7/16" (264mm)
8-1/2" (216mm)
5"
(126mm)
WATERTIGHT
CONDUIT
3-7/16" (87mm)
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)
26-5/8" (676mm)
2-5/16" (58mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)

200-HWI


MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 9
43-3/8" (1102mm)
1/2" (13mm) FLANGE
10-7/16" (264mm)
9-15/16" (252mm)
1/4" (6mm)
Ø 3/16" (5mm)
4-7/8" (125mm)
2-1/2" (63mm)
10-7/16" (264mm)
8-1/2" (216mm)
5"
(126mm)
WATERTIGHT
CONDUIT
1-1/2" (38mm)
44-3/8" (1127mm)
20-1/8" (512mm) WELL
20-1/8" (512mm) WELL
14-15/16" (380mm)
11-15/16" (304mm)
WELL
11-15/16" (304mm)
WELL
13-5/8" (346mm)
6-3/8" (162mm)
WELL
9-5/16" (236mm)
7-9/16" (191mm)
4-1/8" (104mm) 1-13/16"
(46mm)
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
installation



MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 10
installation

1-9/16" (39mm)
40-15/16" (1039mm)
37-7/8" (962mm)
23-1/8" (586mm)
1-1/2" (38mm)
20-3/16" (512mm)
WELL
5"
(126mm)
6-15/16" (175mm)
5" (127mm)
300-HW/D4
5"
(126mm)
6-15/16" (175mm)
5" (127mm)
1-9/16" (39mm)
40-15/16" (1039mm)
37-7/8" (962mm)
WELL
30-3/16" (765mm)
27-1/4" (691mm)
WELL
1-1/2" (38mm)
300-HW/D443
1-7/8" (46mm)
4-1/8" (104mm)
20-3/16" (512mm)
WELL
22-1/16" (559mm)
9/16" (14mm)
FLANGE
7-5/16" (185mm)
5-9/16" (140mm)
4-3/8" (111mm)
WELL
1-7/8" (46mm)
4-1/8" (104mm)
7-5/16" (185mm)
5-9/16" (140mm)
4-3/8" (111mm)
WELL
27-1/4" (691mm)
WELL
29-1/16" (738mm)
9/16" (14mm)
FLANGE
6-7/16"
(163mm)
6-15/16"
(175mm)
1/4" (6mm)
Ø 3/16" (5mm)
4-15/16" (125mm)
2-1/2" (63mm)
39-5/8" (1007mm)
11/16" (17mm)
FLANGE
11/16" (17mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)
3-3/16" (81 mm)
44-1/4" (1123mm)
37-7/8" (962 mm)
WELL
27-1/16" (686mm)
20-3/16" (512mm)
WELL
3-7/16" (87mm)
5"
(126mm)
6-15/16 " (175 mm)
5" (127 mm)
6-15/16" (175 mm)
6-7/16 " (163 mm)
1/4" (6mm)
Ø 3/16" (5mm)
4-15/16" (125mm)
2-1/2" (63mm)
39-11/16" (1007mm)
2-5/16" (59mm)
FLANGE
2-5/16" (59mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
7-5/16" (185mm)
5-9/16" (140 mm)
4-3/8" (111mm)
WELL
20-3/16" (512mm)
WELL
22-1/16" (559mm)
2-1/2" (63mm)
FLANGE
1-7/8" (46mm)
4-1/8" (104mm)
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)
300-HWLF/D4
300-HW


MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 11
installation
39-11/16" (1007mm)
5/8" (16mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
4-15/16" (125mm)
2-1/2" (63mm)
13-7/16" (340mm)
13-15/16" (353mm)
1/4" (6mm)
Ø 3/16" (5mm)
30-1/4" (767mm)
27-1/4" (691mm)
WELL
12" (305mm)
13-15/16" (353mm)
1-7/16" (36mm)
40-7/8" (1038mm)
12" (304mm)
WELL
1-1/2" (38mm)
300-HWI/D443
23-3/16" (588mm)
5"
(126mm)
13-15/16" (353mm)
12" (305mm)
1-7/16" (36mm)
40-7/8" (1038mm)
1-1/2" (38mm)
12" (304mm)
WELL
20-3/16" (512mm)
WELL
300-HWI/D4
7-5/16" (185mm)
1-7/8"
(46mm)
4-1/8" (104mm)
5-9/16" (141mm)
20-3/16" (512mm)
WELL
4-3/8" (111mm)
WELL
22-1/16" (559mm)
5/8" (15mm)
FLANGE
27-1/4" (691mm)
WELL
29-1/16" (738mm)
5/8" (15mm)
FLANGE
7-5/16" (185mm)
5-9/16" (141mm)
1-7/8" (46mm)4-1/8" (104mm)
4-3/8" (111mm)
WELL
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)

39-11/16" (1007mm)
2-5/16" (59mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
27-1/16" (686mm)
20-3/16" (512mm)
WELL
3-7/16" (87mm)
3-1/8" (79mm)
44-1/4" (1124mm)
12" (305mm)
WELL
5"
(126mm)
13-15/16" (353mm)
12" (305mm)
7-5/16" (185mm)
5-9/16" (141mm)
20-3/16" (512mm)
WELL
22-1/16" (559mm)
2-1/2" (63mm)
FLANGE
1-7/8" (46mm)4-1/8" (104mm)
4-3/8" (111mm)
WELL
13-15/16" (353mm)
13-7/16" (340mm)1/4" (6mm)
4-15/16" (125mm)
2-1/2" (63mm)
Ø 3/16" (5mm)
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)
300-HWILF/D4
300-HWI


MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 12
installation
11-15/16" (304mm)
WELL
13-5/8" (346mm)
6-3/8" (162mm)
WELL
9-5/16" (236mm)
7-9/16" (191mm)
4-1/8" (104mm) 1-13/16"
(46mm)
64-5/8" (1642mm)
1/2" (13mm) FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
14-15/16" (380mm)
11-15/16" (304mm)
WELL
1-1/2" (38mm)
65-5/8" (1667mm)
20-1/8" (512mm) WELL
20-1/8" (512mm) WELL 20-1/8" (512mm) WELL
13-7/8" (353mm)
12" (305mm)
5"
(126mm)
WATERTIGHT
CONDUIT
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)
13-7/8" (353mm)
13-3/8" (340mm)
1/4" (6mm)
Ø 3/16" (5mm)
4-7/8" (125mm)
2-1/2" (63mm)



MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 13
22-1/16" (559mm)
20-3/16" (512mm)
WELL
9/16" (14mm) FLANGE
7-5/16" (185mm)
5-9/16" (140mm)
4-3/8" (111mm)
WELL
4-1/8" (104mm)
1-7/8" (46mm)
52-3/4" (1339mm)
5/8" (16mm)
FLANGE
5/8" (16mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
10-7/16" (264mm)
9-15/16" (252mm)
1/4" (6mm)
Ø 3/16" (5mm)
2-1/2" (63mm)
4-15/16" (125mm)
54" (1371mm)
50-15/16" (1294mm)
WELL
1-9/16"
(39mm)
20-3/16" (512mm)
WELL
23-1/8" (586mm)
1-1/2"
(38mm)
5"
(126mm)
10-7/16" (264mm)
8-1/2" (216mm)
400-HW/D4
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)
installation

20-3/16" (512mm)
WELL
27-1/16" (686mm)
3-7/16"
(87mm)
57-5/16" (1455mm)
50-15/16" (1294mm)
WELL
3-3/16"
(81mm)
5"
(126mm)
10-7/16" (264mm)
8-1/2" (216mm)
22-1/16" (559mm)
20-3/16" (512mm)
WELL
2-1/2" (63mm) FLANGE
7-5/16" (185mm)
5-9/16" (140mm)
4-3/8" (111mm)
WELL
4-1/8" (104mm)
1-7/8" (46mm)
52-3/4" (1339mm) 2-5/16"
(58mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
10-7/16" (264mm)
9-15/16" (252mm)
Ø 3/16" (5mm)
1/4" (6mm)
2-1/2" (63mm)
4-15/16" (125mm)
400-HWLF/D4
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)
400-HW


MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 14
installation
20-3/16" (512mm)
WELL
23-3/16" (588mm)
1-1/2"
(38mm)
5"
(126mm)
17-7/16" (442mm)
15-1/2" (394mm)
53-3/4" (1364mm)
1-5/16" (33mm) 12" (305mm)
WELL
52-3/4" (1339mm)
9/16" (14mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
400-HWI/D4
7-5/16" (185mm)
5-9/16" (141mm)
4-3/8" (111mm)
WELL
22-1/16" (559mm)
20-3/16" (512mm)
WELL
5/8" (16mm) FLANGE
4-1/8" (104mm)
1-7/8" (46mm)
17-7/16" (442mm)
2-1/2" (63mm)
4-15/16" (125mm)
16-15/16" (429mm)1/4" (6mm)
Ø 3/16" (5mm)
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)

52-3/4" (1339mm)
2-5/16" (58mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
57-5/16" (1455mm)
3-1/8" (79mm) 12" (305mm)
WELL
20-3/16" (512mm)
WELL
27-1/16" (686mm)
3-7/16"
(87mm)
5"
(126mm)
17-7/16" (442mm)
15-1/2" (394mm)
4-1/8" (104mm)
1-7/8" (46mm)
7-5/16" (185mm)
5-9/16" (141mm)
4-3/8" (111mm)
WELL
22-1/16" (559mm)
20-3/16" (512mm)
WELL
2-1/2" (63mm) FLANGE
400-HWILF/D4
2-1/2" (63mm)
4-15/16" (125mm)
17-7/16" (442mm)
16-15/16" (429mm)
Ø 3/16" (5mm)
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)
400-HWI


MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 15
65-3/4" (1670mm)
11/16" (17mm)
FLANGE
11/16" (17mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
22-1/16" (559mm)
20-3/16" (512mm)
WELL
9/16" (14mm) FLANGE
4-1/8" (104mm)
1-7/8" (46mm)
7-5/16" (185mm)
5-9/16" (140mm)
4-3/8" (111mm)
WELL
20-3/16" (512mm)
WELL
23-1/8" (586mm)
1-1/2"
(38mm)
67-1/16" (1702mm)
63-15/16" (1625mm)
WELL
1-9/16" (39mm)
10-7/16" (264mm)
8-1/2" (216mm)
5"
(126mm)
10-7/16" (264mm)
9-15/16" (252mm)
1/4" (6mm)
Ø 3/16" (5mm)
2-1/2" (63mm)
4-15/16" (125mm)
500-HW/D4
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)
installation

7-5/16" (185mm)
5-9/16" (140mm)
4-3/8" (111mm)
WELL
22-1/16" (559mm) 20-3/16" (512mm)
WELL
2-1/2" (63mm) FLANGE
4-1/8" (104mm)
1-7/8" (46mm)
65-3/4" (1670mm)
2-5/16" (58mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
70-7/16" (1787mm)
64" (1625mm)
WELL
20-3/16" (512mm)
WELL
27-1/16" (686mm)
3-7/16"
(87mm)
10-7/16" (264mm)
8-1/2" (216mm)
5"
(126mm)
500-HWLF/D4
10-7/16" (264mm)
9-15/16" (252mm)
1/4" (6mm)
Ø 3/16" (5mm)
2-1/2" (63mm)
4-15/16" (125mm)
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)
500-HW


MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 16
installation
66-13/16" (1696mm)
1-5/16" (33mm) 12" (304mm)
WELL
20-3/16" (512mm)
WELL
23-3/16" (588mm)
1-1/2"
(38mm)
20-15/16" (531mm)
19" (483mm)
5"
(126mm)
4-1/8" (104mm)
1-7/8" (46mm)
22-1/16" (559mm)
20-3/16" (512mm)
WELL
5/8" (16mm) FLANGE
7-5/16" (185mm)
5-9/16" (141mm)
4-3/8" (111mm)
WELL
500-HWI/D4
20-15/16" (531mm)
20-7/16" (518mm)1/4" (6mm)
2-1/2" (63mm)
4-15/16" (125mm)
Ø 3/16" (5mm)
65-3/4" (1670mm)
9/16" (13mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)

65-3/4" (1670mm)
2-5/16" (58mm)
FLANGE
6" (152mm)
Optional stainless steel heat shield
(not factory supplied)
70-3/8" (1787mm)
3-1/8" (79mm) 12" (305mm)
WELL
20-3/16" (512mm)
WELL
27-1/16" (686mm)
3-7/16"
(87mm)
20-15/16" (531mm)
19" (483mm)
5"
(126mm)
22-1/16" (559mm) 20-3/16" (512mm)
WELL
2-1/2" (63mm) FLANGE
4-1/8" (104mm)
1-7/8" (46mm)
7-5/16" (185mm)
5-9/16" (141mm)
4-3/8" (111mm)
WELL
20-15/16" (531mm)
20-7/16" (518mm)1/4" (6mm)
Ø 3/16" (5mm)
2-1/2" (63mm)
4-15/16" (125mm)
500-HWILF/D4
6" (152mm)
Conduit when
exiting bottom
11" (278mm)
6"
(152mm)
5"
(126mm)
Conduit when
exiting back
4-15/16" (125mm)
4" (102mm)
500-HWI


MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 17
installation
Model
Overall Exterior Well Interior
Height Width Depth Height Width Depth
100-HW/D4 7" (177mm) 15" (380mm) 23-1/8" (586mm) 4-3/8" (111mm) 12" (304mm) 20-3/16" (512mm)
100-HW/D6 8-7/8" (225mm) 15" (380mm) 23-1/8" (585mm) 6-3/8" (162mm) 12" (304mm) 20-3/16" (512mm)
100-HW/D443 6-5/16" (159mm) 15" (380mm) 30-3/16" (765mm) 4-3/8" (111mm) 12" (304mm) 27-1/4" (691mm)
100-HW/D643 8-3/16" (207mm) 15" (380mm) 30-3/16" (765mm) 6-3/8" (162mm) 12" (304mm) 27-1/4" (691mm)
100-HWLF/D4 7" (177mm) 18-5/16" (465mm) 27-1/16" (686mm) 4-3/8" (111mm) 12" (304mm) 20-3/16" (512mm)
100-HWLF/D6 8-7/8" (225mm) 18-5/16" (465mm) 27-1/16" (686mm) 6-3/8" (162mm) 12" (304mm) 20-3/16" (512mm)
200-HW/D4 7-5/16" (185mm) 28-1/16" (712mm) 23-1/8" (586mm) 4-3/8" (111mm) 25" (635mm) 20-3/16" (512mm)
200-HW/D6 9-5/16" (235mm) 28-1/16" (712mm) 23-1/8" (586mm) 6-3/8" (162mm) 25" (635mm) 20-3/16" (512mm)
200-HW/D443 7-5/16" (184mm) 28-1/16" (712mm) 30-3/16" (765mm) 4-3/8" (111mm) 12" (304mm) 27-1/4" (691mm)
200-HW/D643 9-3/16" (233mm) 28-1/16" (712mm) 30-3/16" (765mm) 6-3/8" (162mm) 12" (304mm) 27-1/4" (691mm)
200-HWLF/D4 7-5/16" (184mm) 31-3/8" (796mm) 27-1/16" (686mm) 4-3/8" (111mm) 25" (635mm) 20-3/16" (512mm)
200-HWLF/D6 9-1/4" (234mm) 31-3/8" (796mm) 27-1/16" (686mm) 6-3/8" (162mm) 25" (635mm) 20-3/16" (512mm)
200-HWI/D4 7-5/16" (185mm) 27-5/8" (701mm) 23-3/16" (588mm) 4-3/8" (111mm) 12" (304mm) 20-3/16" (512mm)
200-HWI/D6 9-5/16" (236mm) 27-5/8" (701mm) 23-3/16" (588mm) 6-3/8" (162mm) 12" (304mm) 20-3/16" (512mm)
200-HWI/D443 7-5/16" (185mm) 27-5/8" (701mm) 30-1/4" (767mm) 4-3/8" (111mm) 12" (304mm) 27-1/4" (691mm)
200-HWI/D643 9-1/4" (234mm) 27-5/8" (701mm) 30-1/4" (767mm) 6-3/8" (162mm) 12" (304mm) 27-1/4" (691mm)
200-HWILF/D4 7-5/16" (185mm) 31-1/4" (792mm) 27-1/16" (686mm) 4-3/8" (111mm) 12" (304mm) 20-3/16" (512mm)
200-HWILF/D6 9-5/16" (236mm) 31-1/4" (792mm) 27-1/16" (686mm) 6-3/8" (162mm) 12" (304mm) 20-3/16" (512mm)
300-HW/D4 7-5/16" (185mm) 40-15/16" (1039mm) 23-1/8" (586mm) 4-3/8" (111mm) 37-7/8" (962mm) 20-3/16" (512mm)
300-HW/D6 9-1/4" (234mm) 40-15/16" (1039mm) 23-1/8" (586mm) 6-3/8" (162mm) 37-7/8" (962mm) 20-3/16" (512mm)
300-HW/D443 7-5/16" (185mm) 40-15/16" (1039mm) 30-3/16" (765mm) 4-3/8" (111mm) 37-7/8" (962mm) 27-1/4" (691mm)
300-HW/D643 9-3/16" (233mm) 40-15/16" (1039mm) 30-3/16" (765mm) 6-3/8" (162mm) 37-7/8" (962mm) 27-1/4" (691mm)
300-HWLF/D4 7-5/16" (185mm) 44-1/4" (1123mm) 27-1/16" (686mm) 4-3/8" (111mm) 37-7/8" (962mm) 20-3/16" (512mm)
300-HWLF/D6 9-1/8" (232mm) 44-1/4" (1123mm) 27-1/16" (686mm) 6-3/8" (162mm) 37-7/8" (962mm) 20-3/16" (512mm)
300-HWI/D4 7-5/16" (185mm) 40-7/8" (1038mm) 23-3/16" (588mm) 4-3/8" (111mm) 12" (304mm) 20-3/16" (512mm)
300-HWI/D6 9-1/4" (234mm) 40-7/8" (1038mm) 23-3/16" (588mm) 6-3/8" (162mm) 12" (304mm) 20-3/16" (512mm)
300-HWI/D443 7-5/16" (185mm) 40-7/8" (1038mm) 30-1/4" (767mm) 4-3/8" (111mm) 12" (304mm) 27-1/4" (691mm)
300-HWI/D643 9-1/4" (234mm) 40-7/8" (1038mm) 30-1/4" (767mm) 6-3/8" (162mm) 12" (304mm) 27-1/4" (691mm)
300-HWILF/D4 7-5/16" (185mm) 44-1/4" (1124mm) 27-1/16" (686mm) 4-3/8" (111mm) 12" (304mm) 20-3/16" (512mm)
300-HWILF/D6 9-1/4" (234mm) 44-1/4" (1124mm) 27-1/16" (686mm) 6-3/8" (162mm) 12" (304mm) 20-3/16" (512mm)
400-HW/D4 7-5/16" (185mm) 54" (1371mm) 23-1/8" (586mm) 4-3/8" (111mm) 50-15/16" (1294mm) 20-3/16" (512mm)
400-HW/D6 9-5/16" (235mm) 54" (1371mm) 23-1/8" (586mm) 6-3/8" (162mm) 50-15/16" (1294mm) 20-3/16" (512mm)
400-HWLF/D4 7-5/16" (185mm) 57-5/16" (1455mm) 27-1/16" (686mm) 4-3/8" (111mm) 50-15/16" (1294mm) 20-3/16" (512mm)
400-HWLF/D6 9-5/16" (235mm) 57-5/16" (1455mm) 27-1/16" (686mm) 6-3/8" (162mm) 50-15/16" (1294mm) 20-3/16" (512mm)
400-HWI/D4 7-5/16" (185mm) 53-3/4" (1364mm) 23-3/16" (588mm) 4-3/8" (111mm) 12" (304mm) 20-3/16" (512mm)
400-HWI/D6 9-5/16" (236mm) 53-3/4" (1364mm) 23-3/16" (588mm) 6-3/8" (162mm) 12" (304mm) 20-3/16" (512mm)
400-HWILF/D4 7-5/16" (185mm) 57-5/16" (1455mm) 27-1/16" (686mm) 4-3/8" (111mm) 12" (304mm) 20-3/16" (512mm)
400-HWILF/D6 9-5/16" (238mm) 57-5/16" (1455mm) 27-1/16" (686mm) 6-3/8" (162mm) 12" (304mm) 20-3/16" (512mm)
500-HW/D4 7-5/16" (185mm) 67-1/16" (1702mm) 23-1/8" (586mm) 4-3/8" (111mm) 63-15/16" (1625mm) 20-3/16" (512mm)
500-HW/D6 9-5/16" (235mm) 67-1/16" (1702mm) 23-1/8" (586mm) 6-3/8" (162mm) 63-15/16" (1625mm) 20-3/16" (512mm)
500-HWLF/D4 7-5/16" (185mm) 70-7/16" (1787mm) 27-1/16" (686mm) 4-3/8" (111mm) 64" (1625mm) 20-3/16" (512mm)
500-HWLF/D6 9-5/16" (235mm) 70-7/16" (1787mm) 27-1/16" (686mm) 6-3/8" (162mm) 64" (1625mm) 20-3/16" (512mm)
500-HWI/D4 7-5/16" (185mm) 66-13/16" (1696mm) 23-3/16" (588mm) 4-3/8" (111mm) 12" (304mm) 20-3/16" (512mm)
500-HWI/D6 9-5/16" (236mm) 66-13/16" (1696mm) 23-3/16" (588mm) 6-3/8" (162mm) 12" (304mm) 20-3/16" (512mm)
500-HWILF/D4 7-5/16" (185mm) 70-3/8" (1787mm) 27-1/16" (686mm) 4-3/8" (111mm) 12" (304mm) 20-3/16" (512mm)
500-HWILF/D6 9-5/16" (238mm) 70-3/8" (1787mm) 27-1/16" (686mm) 6-3/8" (162mm) 12" (304mm) 20-3/16" (512mm)


MN-37234 (Rev. 3) 06/16 • Hot Food Holding Drop-In Well • 18
installation

 
(W x D)

(H x W x D)
100-HW/D4 or D6 one full-size
100-HWLF/D4 or D6 one full-size
14-1/4" x 22-1/2"
(363mm x 572mm)
4-1/4" x 5-1/4" x 10-13/16"
(108mm x 133mm x 274mm)
100-HW/D443 or D643 one full & one third-size pan 14-1/4" x 29-1/2"
(363mm x 749mm)
4-1/4" x 5-1/4" x 10-13/16"
(108mm x 133mm x 274mm)
200-HW/D4 or D6 two full-size pans
200-HWLF/D4 or D6 two full-size pans
27" x 22-1/2"
(686mm x 572mm)
4-1/4" x 5-1/4" x 10-13/16"
(108mm x 133mm x 274mm)
200-HW/D443 or D643 two full & two third-size pans 27" x 29-1/2"
(686mm x 749mm)
4-1/4" x 5-1/4" x 10-13/16"
(108mm x 133mm x 274mm)
200-HWI/D4 or D6 two full-size pans
200-HWILF/D4 or D6 two full-size pans
27" x 22-1/2"
(686mm x 572mm)
4-1/4" x 8-3/4" x 10-13/16"
(108mm x 222mm x 274mm)
200-HWI/D443 or D643 two full & two third-size pans 27" x 29-1/2"
(686mm x 749mm)
4-1/4" x 8-3/4" x 10-13/16"
(108mm x 222mm x 274mm)
200-HWIS/D6 two full-size pans 44" x 14-1/4"
(1118mm x 362mm)
4-1/4" x 8-3/4" x 10-13/16"
(108mm x 222mm x 274mm)
300-HW/D4 or D6 three full-size pans
300-HWLF/D4 or D6 three full-size pans
40" x 22-1/2"
(1016mm x 572mm)
4-1/4" x 5-1/4" x 10-13/16"
(108mm x 133mm x 274mm)
300-HW/D443 or D643 three full & three third-size pans 40" x 29-1/2"
(1016mm x 749mm)
4-1/4" x 5-1/4" x 10-13/16"
(108mm x 133mm x 274mm)
300-HWI/D4 or D6 three full-size pans
300-HWILF/D4 or D6 three full-size pans
40" x 22-1/2"
(1016mm x 572mm)
4-1/4" x 12-1/4" x 10-13/16"
(108mm x 311mm x 274mm)
300-HWI/D443 or D643 three full & three third-size pans 40" x 29-1/2"
(1016mm x 749mm)
4-1/4" x 12-1/4" x 10-13/16"
(108mm x 311mm x 274mm)
300-HWIS/D6 three full-size pans 65-1/4" x 14-1/4"
(1657mm x 362mm)
4-1/4" x 12-1/4" x 10-13/16"
(108mm x 311mm x 274mm)
400-HW/D4 or D6 four full-size pans
400-HWLF/D4 or D6 four full-size pans
53-1/8" x 22-1/2"
(1350mm x 572mm)
4-1/4" x 8-3/4" x 10-13/16"
(108mm x 222mm x 274mm)
400-HWI/D4 or D6 four full-size pans
400-HWILF/D4 or D6 four full-size pans
53-1/8" x 22-1/2"
(1350mm x 572mm)
4-1/4" x 15-3/4" x 10-13/16"
(108mm x 400mm x 274mm)
500-HW/D4 or D6 five full-size pans
500-HWLF/D4 or D6 five full-size pans
66-1/4" x 22-1/2"
(1683mm x 572mm)
4-1/4" x 8-3/4" x 10-13/16"
(108mm x 222mm x 274mm)
500-HWI/D4 or D6 five full-size pans
500-HWILF/D4 or D6 five full-size pans
66-1/4" x 22-1/2"
(1683mm x 572mm)
4-1/4" x 19-1/4" x 10-13/16"
(108mm x 489mm x 274mm)

Put clip in highest pair of slots
that fit under the counter
Tighten screw so that it presses against
the counter, holding the well in place
One clip for each corner
Rough Cut Openings Locking Kit Installation