Alva GHP24 User manual

IMPORTANT SAFETY INFORMATION
As with all gas appliances, misuse of this appliance or failure
• THIS UNIT MUST BE THOROUGHLY CHECKED BEFORE
•
•
•
• For use with LP gas only
•
•
• Phone the customer care line at 086 100 ALVA (2582) or email
•
•
•
•
•
•
•
•
• DO NOT unscrew the regulator while the patio heater is on or if
•
•
•
•
•
•
•
•
•
•
•
•
Please read the
instructions carefully
before use.
Retain this manual for
future reference.
warranty

1
1
2
2
3
4
5
6
7 - 11
11 - 12
12
13
14
14
15-16
16-17
17
17
18
INDEX
INDEX
WARRANTY
GENERAL INFORMATION
ASSEMBLY
HEATER SET UP
PARTS DIAGRAM - GHP24
PARTS DIAGRAM - GHP25
ASSEMBLY PARTS - GHP24
ASSEMBLY PARTS - GHP25
PARTS LISTING AND TOOLS REQUIRED
AND ASSEMBLY INSTRUCTIONS
LOCATION
LEAK TEST
USING YOUR HEATER
CHANGING YOUR CYLINDER
MAINTENANCE
FREQUENTLY ASKED QUESTIONS
TROUBLE SHOOTING GUIDE
SPECIFICATIONS
AFTER SALES SERVICE
KEY
Important information
Cautions and
warnings.
Danger
Contact an approved
ALVA technician.
Do It Yourself
Instructional
video available

WARRANTY
PLEASE RETAIN YOUR PROOF OF PURCHASE FOR
GENERAL INFORMATION
086 100 ALVA (2582)
-
-
Thank you for your
purchase of this
Patio heater.
Please read these
instructions carefully
before use and keep
them in a safe place,
for future reference.
Not using gas and/
or gas appliances
according to the
instructions is
extremely dangerous
and can lead to
property damage,
injury or death.
For outdoor use only.
For use with LPG only
DO NOT use within
surfaces.
Always turn OFF the
gas supply at the
cylinder after use.
DO NOT store
another cylinders near
the heater.
1

ASSEMBLY
•
•
•
• -
(Figure A).
HEATER SET UP
(Figure B)
2
Fig.A
Fig.B
Nose cone
sealing washer

•
PARTS DIAGRAM
1830 mm
890 mm 770 mm
565 mm
460 mm
Reflector
Upper Protective Mesh
Rhombic Protective Mesh
Control Box
Tank housing
Base
Wheel
GHP24 - CYLINDRICAL
GLASS TUBE PATIO HEATER
3

GHP25 - CYLINDRICAL
GLASS TUBE PATIO HEATER
•
PARTS DIAGRAM
2100 mm
890 mm 1060 mm
565 mm
460 mm
Reflector
Upper Protective Mesh
Protective Guard
Control Box
Tank housing
Base
Wheel
4

•
ASSEMBLY PARTS - GHP24
Reflector
Upper Protective Mesh
Heating Body
Cylinder Housing
Base
Wheel
A
B
D
F
G
Mesh C
Gas Hose E
H
5

•
ASSEMBLY PARTS - GHP25
Reflector
Upper Protective Mesh
Heating Body
Cylinder Housing
Base
Wheel
A
B
D
F
G
Mesh C
Gas Hose E
H
6

PARTS LISTING AND TOOLS REQUIRED
7

STEP 1
8
STEP 2
F
DD

STEP 3
D
DD
9
STEP 4
C
DD

10
STEP 5
B
CAUTION:
Do not hang clothing or any
the heater, or place on or near
HOT! DO NOT TOUCH!
STEP 6
AA
BB
CC
A

STEP 7
Warning :
Ensure the hose does
not make contact with
any high temperature
surfaces, or it may
melt and leak causing
The LP regulator/hose
assembly must be
located out of path-
ways where people
may trip over it or in
an area where the
hose will not be
subject to accidental
damage.
LOCATION
•
•
• Maintain proper clearance from
•
• NEVER operate the heater in the
•
•
• Brush the connections (heater to
CEILING
WALL
100 cm
100 cm
11
LOCATION
LOCATION

LEAK TEST
•
• Brush the connections (heater
• -
Fig.J)
•
•
• If you are unsure or if you
cannot tighten the connection,
086 100 ALVA
(2582)
•
Fig.J
Foamy
bubbles
indicate a
leak
Connection
in assembly
Connections to be leak tested
Regulator into cylinder
Hose to regulator
Hose to appliance
FOR YOUR SAFETY
IF YOU SMELL GAS
• Turn off the gas
supply at the
bottle.
• Extinguish all
DO NOT operate
any electrical
appliances.
• Ventilate the
area.
• Check for leaks
(see LEAK TEST)
• If odour per-
sists, contact
your dealer or
local gas supplier
immediately.
Before proceeding to
ignite the heater, make
sure you understand
the “IMPORTANT
SAFETY
INFORMATION”
section of this manual.
http://www.
youtube.com
/watch?v=8L
pZ1B0m23Y
&feature=plcp
How to do
a leak test
12
• -
Fig.J)
•
•
• If you are unsure or if you
cannot tighten the connection,
086 100 ALVA
(2582)
•

USING YOUR HEATER
Smoke and odour
caused by the heating
of oils used during
manufacturing will
occur when lighting
time. This is normal
and there is no
reason for alarm.
Avoid inhaling the
fumes!
The smoke and odour
should dissipate within
3 - 4 minutes.
Check the heater
immediately if any of
the following occurs:
• The heater does
not reach tem-
perature.
• The burner
makes popping
noise during use
(a slight noise is
normal when the
burner is extin-
guished).
• Smell of gas in
conjunction with
extreme yellow
tipping of the
13
Variable control knob
Pointer
L
O
W
HIGH
PILOT
FFO
I
G
N
I
T
E
P
u
s
h
t
o
t
u
r
n
OFF: the heater stop work
HIGH: maximum temperature position
LOW: minimum temperature position

•
•
• -
•
CHANGING YOUR CYLINDER
14

MAINTENANCE
• -
•
•
•
•
•
•
•
•
•
•
15

•
Storage
•
•
•
•
FREQUENTLY ASKED QUESTIONS
16

?
TROUBLE SHOOTING GUIDE
Pilot will not
light OFF
Air in supply system
Loose connections
Clean or replace
opening
Purge air from lines
17
http://www.
youtube.com/
watch?v=Ya
vsYE8nzCw
&feature=plcp
How to test if
your cylinder
is overfilled
Pilot will not
stay on
Loose connections
pressure
Tighten connections
Replace thermocouple
Burner will
not light
Pressure is low
Control not ON
Not in correct
location
Replace thermocouple
retry