Amantii TRU-VIEW-XL User manual

Fix your Fireplace
TRU-VIEW-XL
All manuals and user guides at all-guides.com
all-guides.com

Content
•How to replace LED light
•How to replace flicker motor
•How to replace heating element
•How to replace the PCB board
•How to replace the signal receiver
•How to replace the top light
All manuals and user guides at all-guides.com

Replace LED light
Unscrew the knobs on both sides of the unit and then remove
the glass.
Step 1
Knob on
each side
Replace emberbed LED light
All manuals and user guides at all-guides.com

After two knobs are removed, the
front glass be released and come away
from the unit. Take care to catchit.
Front glass
All manuals and user guides at all-guides.com

Step 2
Unscrew twoscrews on both sides and then
totake off two barsand the ember bed glass
panel
Zoomed view
All manuals and user guides at all-guides.com

After the knobs and fending bars are removed,
you can remove the ember bed glass panel and
long steel bar with it.
All manuals and user guides at all-guides.com
all-guides.com

Step 3
After the ember bed glass panel is removed, youcan now replace
the LED lightfor ember bed effect.(Replace flame light see STEP 4)
All manuals and user guides at all-guides.com

Step 4
Zoomed view
Zoomed view
Unscrew 2 screws on the left side
and 2 screws on the right side of
the fireplace (where the arrows
marked) to take off the fending
bars. After the bars are removed,
you can remove two side glass
panels.
All manuals and user guides at all-guides.com

Screws and fending bars Side glass panels
Afterscrews and fending bars are removed,
now you can remove the side glass panels.
All manuals and user guides at all-guides.com

Zoomed view
The top light located here
Unscrew 3 screws located in the canopy of the
unit then disconnect cable toremove the top
light from the fireplace.
Step 5
All manuals and user guides at all-guides.com

The fending bar located here
Remove the screws
and take off the fending
bar. (Zoomed picture
in the next page)
Step 6
All manuals and user guides at all-guides.com
all-guides.com

Fending bar
Screws that attach
the fending bar
All manuals and user guides at all-guides.com

Visual glass panel
Hook
Fending bar
Step 7
After fending bar is removed, you can now
remove the visual glass panel using the small
brackets are used to hold the front glass panel
In place. These would have been removed in step
1.
Push the bracket into
the gap between
the glass and the
fireplace, using it to
Hook the glass and
Pulling towards you.
All manuals and user guides at all-guides.com

Step 8
Afterthe visual glass panel is removed, you can now replace
LED light for flame effect.
All manuals and user guides at all-guides.com

Replace the flicker motor
Please follow the same 1 – 7 steps as changing the LED light.
Continue from this point on.
All manuals and user guides at all-guides.com

Unscrew 4 screws
Unplug
Now you can replace the
flickermotor for ember
bed effect
Step 2
All manuals and user guides at all-guides.com
all-guides.com

The flicker motor for ember bed effect is beneath the ember
bed glass panel.
Step 1
Unscrew the screw and then disconnect
the flicker rod from the motor
Replace flicker motor for ember bed effect
All manuals and user guides at all-guides.com

The flicker motor for flame effect is behind the visual glass panel.
Unscrew the screw and then disconnect
the flicker rod from the motor
Step 3
Replace flicker motor for flame effect
All manuals and user guides at all-guides.com

Unscrew 4 screws, unplug and now
youcan replace flicker motor for flame
effect.
Step 4
All manuals and user guides at all-guides.com

Replace the heating element
Please follow Steps 1 and 2 as in replacing LED light.
You will then continue from here:
The heating element located here
All manuals and user guides at all-guides.com