Amart Furniture GERALDTON 62259 User manual

Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Freecall 1800 351 084.
895mm
615mm
580mm
1
62259
ASSEMBLY INSTRUCTION
GERALDTON - OUTDOOR CHAIR
ITEM CODE - 62259
Imported by Amart Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please phone
Amart Furniture, Customer Service Freecall 1800 351 084.

ADDITIONAL TOOLS REQUIRED
12 1
2
3
4
5
6
7
8
9
10
11
ALLOW 15 MINUTES
X
1
1 PEOPLE REQUIRED
2
PRE-ASSEMBLY PREPARATION
BEFORE YOU START:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that
may damage the product.
2. Take care when lifting. Product should be assembled as near as possible to
the point of use
3. Ensure that you have all required contents for complete assembly.
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads.
62259

3
BACK
1
2
3
4
5
BASE
ARM
LEG
BRACE RAIL
INSERTED NUTS
INSERTED NUTS
62259

4
STEP 1 : Insert pin (d) into arm (3).
d
3
62259
STEP 2 : Insert barrel (d) into leg (4). Then attach arm (3) to leg (4), using additional tool to secure.
d
3
4
3
4
4
d
3

5
STEP 3 : Insert screw (e) from base (2) into back (1). Use allen key (f) to secure.
62259
STEP 4 : Insert bolt (c) from leg (4) into base (2). Use allen key (f) to secure.
c
f
CAP
2
4

6
STEP 5 : Insert bolt (a) from leg (4) into brace rail (5). Use allen key (f) to secure.
62259
STEP 6 : Flip 180 degrees.
4
5
NUT
f
a
a

7
STEP 7 : Insert bolt (c) from leg (4) into base (2). Use allen key (f) to secure.
62259
STEP 8 : Insert bolt (a) from leg (4) into brace rail (5). Use allen key (f) to secure.
4
2
5
c
f
a
a
f
4
NUT
5

8
STEP 9 : Insert bolt (b) from back (1) into arm (3). Use allen key (f) to secure.
ASSEMBLY IS COMPLETE
62259
IMPORTANT NOTE:
BEFORE FINALLY TIGHTENING THE BOLTS, PLACE THE ASSEMBLED CHAIR UPRIGHT ON A LEVEL
SURFACE AND SIT CAREFULLY ON THE CHAIR TO ENSURE THE CHAIR LEGS ARE ALIGNED AND
LEVEL. THEN TIGHTEN ALL BOLTS AND YOUR CHAIR IS READY FOR USE.
NUT
b
f
3
1
b
3
1

CARE AND MAINTENANCE
READ CAREFULLY: SURFACE PREPARATION.
STEP 1.After the product is assembled and before oil treatment, thoroughly wipe clean your furniture
underneath and on top, remove all dirt and sawdust particles from all mortise joints and grooves
using a brush and rag or wash with hose on grass area.
STEP 2. OILING:. Oil in the shade or under cover. We recommend the furniture to be completely
covered and sealed underneath and on top with the a light coat of hardwood timber oil preservative,
make sure the oil penetrates into all grooves and mortise joints.
STEP 3. IMPORTANT. After oiling wipe off excess oil, then allow the oil to dry in the shade away
from direct sunlight until dry, then wipe off again with a clean rag removing any excess oil that may
not have penetrated into the timber. Repeat wiping off excess oil if necessary.
STEP 4. REPEAT THE ABOVE PROCEDURE IN 48HRS. Sanding is not required between
these initial coats. Your furniture is now protected however repeat applications of the
hardwood timber oil may be required. Before re- oiling check your furniture for any residue
build up, if this occurs a light sanding may be required. Note: The frequency of oiling will vary
according to the climatic conditions in your area and direct exposure to the elements your
furniture is subjected too
NOTE: If Eucalyptus furniture is neglected with prolonged unprotected exposure to the elements
this will cause the timber to discolor to asilvery grey, cracking and hairline cracks may appear if
in the event your setting does discolor to restore the timber, sanding and oiling will be required. We
recommend the furniture be stored with undercover protection during wintertime and wet season.
NOTE: WET TIMBER MUST BE DRIED FOR 3-5 DAYS BEFORE OILING. DO NOT OIL THE
FURNITURE LATE IN THE DAY WHEN DEW OR CONDENSATION IS LIKELY TO FORM OR WHEN
RAIN IS THREATENING.
NOTE: ALL TIMBER FURNITURE GOES THROUGH ASETTLING IN PERIOD, FASTENERS
MUST BE TIGHTENED REGULARLY. DO NOTLEAVE FASTENERS UNTIGHTENED THIS
COULD CAUSE FURNITURE DAMAGE.
Eucalyptus-timber iskiln dried under strict guidelines. Upon purchasing your furniture
small hairline cracks may appear, this ispartofthe drying process ofthis particular timber
species, these cracks will not deter the durability of the furniture, upto3% shrinkage may
occur inthis species oftimber.
WARNING: Staining on Tuscan or light colored pavers may occur from sap leaching and dust
particles if the timber is not cleaned properly and weathered correctly, hose down your
furniture and clean thoroughly before placing your furniture on light colored pavers.
Storing or covering product with outdoor furniture covers when it's not in use. This will also
extend your furniture's life.