American Standard TONIC 3/6 Lpf User manual

Bring the toilet as the mark defined, and then mark the holes' position at the back of the toilet
(as the figures shown in the pictures below)
Use the 10mm. drillbit
for bore the holse through the floor.
Cutting of the waste connector as the figures shown in the pictures below.
(In case lenght of trap way is 305 mm.)
(In case lenght of trap way is not 305 mm.)

Connect the waste connector into the toilet
Installing the toilet with the floor
Install the water supply hose Attaching the tank
Water Level Adjustment
Attach The Water Supply Hose To The Stop Valve
Lift the toilet assembly and install
by assemblings the outlet edge of
waste connector with the waste inlet
as the mark defined.
Attach the water supply hose properly
to the water control valve of the tank.
And then tighten snugly by hand.
Attach the water supply hose to
the stop valve. And then tighten
snugly by hand. Turn on the water
to test for leakage occurs, use a
wrench to tighten the connection
carefully untill the leakage stops.
Adjust the water level in the tank to
point indicated on the tank wall,
as shown in the picture.
Gather all the components first. Insert the rubber gasket
in the water outlet hole, then place the tank over it,
ensuring a secure fit. Next, place a rubber washer on
each of the 2 bolts and insert these through their respective
holes. Place the washer and the nut on the end of the bolt
tighten alternately one side, then the other untill snug. Be
sure the tank is level. Do not tighten the nuts too much.
it will break the vitreous china.
After the installation with above
instruction, check the levelness
with the use of level gauge from
side to side (left & right)
The picture shows
the completely connector
into toilet.
Fixing the toilet with the floor
By using the screw with the floor fixing set
(supplied)
¹Ó¶Ñ§¾Ñ¡¹éÓ·Õè»ÃСͺÍØ»¡Ã³ì¶Ñ§¾Ñ¡¹éÓàÃÕºÃéÍÂáÅéÇ µÒÁÇÔ¸Õ¡Ò÷Õèá¹Ð¹Ó
äÇéÊÓËÃѺÍØ»¡Ã³ìÃØè¹¹Ñé¹æ â´Â¡ÒÃãªé¹ç͵ÂÖ´ÃÐËÇèÒ§Ãٶѧ¾Ñ¡¹éÓáÅÐâ¶ÊéÇÁ
´éÒ¹ã¹â´ÂÁÕÂÒ§Ãͧ¶Ñ§¾Ñ¡¹éӵçµÓá˹觷ҧ¹éÓŧ¢Í§¶Ñ§¾Ñ¡¹éÓ ¢Ñ¹¹ç͵
ÂÖ´ÊÅѺ¡Ñ¹ 2 ¨Ø´ ´éÇÂÁ×ͨ¹á¹è¹ áÅÐãªé»ÃÐᨢѹÂÖ´¹ç͵·Ñé§ 2 ¨Ø´
ÍÕ¡¤ÃÑé§ ¤ÇÃÃÐÇѧ¡Òâѹá¹è¹à¡Ô¹ä» à¾ÃÒШзÓãËé¶Ñ§¾Ñ¡¹éÓáÅÐâ¶ÊéÇÁ
ºÃÔàdz¹Ñé¹áµ¡ä´éáÅФÇÃãËé¶Ñ§¾Ñ¡¹éÓä´éÃдѺäÁèà͹àÍÕ§

Install The Toilet Seat (See the manual for installing Seat&Cover)
Install the toilet seat
and apply silicone sealant
around the bowl.