American Time SiteSync IQ User manual

Your SiteSync IQ system is now set up for proper operation.
For information on other features, see the Installation and
Operation Manual that was included with your system. If you
have any questions, please contact Technical Support at
American Time: 800-328-8996.
6
Activate and hang your clocks
Don't activate the battery or apply power to the clocks until the system controller is installed and
transmitting and the clock is in the intended location.
American Series Digital Clocks
1. Take the clock to the area where it will be used.
2. To activate the clock, connect to 120vac power.
3. Display will ash “U40” or 1:00 o’clock until it
receives a signal.
4. Verify synchronization takes place within 2-5
minutes.
SiteSync IQ®Wireless Clock System
GPS Plus with Campus TX Antenna
INST-SSIQ-C-P Rev 10
Please read this rst!
After determining the proper wattage for your facility, we guarantee the coverage of your SiteSync IQ
when you follow a few simple steps. If this is your rst installation or you have questions at any time
during this process, please call American Time toll free at 800-328-8996.
We're here to help!
This Quick Start Guide will help you avoid three common installation mistakes:
1. Improper location of transmitting (TX) antenna. A temporary install of the system controller
is recommended.
Don't drill holes for permanent installation and mounting until the system is working correctly.
2. Improper system controller start-up. A successful transmission is indicated by a TX in the
lower right-hand corner of the system controller screen.
Don't locate the campus TX antenna within 4' of the system controller.
3. Improper clock start-up. Activate clocks in their intended location.
Don't activate the clocks in one room and move them to another location as signal reception
will not be veried. Make sure the system controller is transmitting and is not in Quiet Mode.
Important Note: Clocks should be installed within 24 hours of installing the system controller. After
24 hours, the system controller will enter Quiet Mode. Pressing 3-5-7 on the keypad will disable Quiet
Mode for 6 hours. Reference Appendix J in the SiteSync IQ Installation and Operation Manual for
more details on Quiet Mode.
Reset
Button
LED
Electric
Electric (AC) Analog Clocks
1. Take the clock to the area where it will be used.
2. To activate the clock, connect to AC power.
The LED on the back of the clock (see below)
will ash red within 30 seconds of power-up to
indicate receiver is looking for the wireless
signal.
When the signal is received, the LED will ash
green. Be patient. The clock hands will rapid
advance to the correct time. This may take
up to 7 minutes.
3. Hang the clock once signal reception is
veried and clock is operating correctly.
Note: If the LED does not ash within 30 seconds,
disconnect the barrel plug on the clock receiver, wait
10 seconds and reconnect. The LED will begin ashing
within 30 seconds.
Activation Note: Clocks should be installed within 24 hours
of installing the system controller. After 24 hours, the system
controller will enter Quiet Mode. Pressing 3-5-7 on the keypad
will disable Quiet Mode for 6 hours. Reference Appendix J in the
SiteSync IQ Installation and Operation Manual for more details
on Quiet Mode.
phone: [phone] fax: [phone] online: american-time.com
mail: 140 3rd St. So.; PO Box 707, Dassel, MN 55325-0707
AC
DC
To
wiring
box
LED
Battery
Barrel
Jack
Input
Battery Analog Clocks
1. Take the clock to the area where it will be
used.
2. To activate the clock, connect barrel jack plug
of battery pack to wireless receiver. The
LED on the back of the clock will ash red
within 30 seconds of power-up to indicate
receiver is looking for the wireless signal.
When the signal is received, the LED will ash
green. Be patient. The clock hands will rapid
advance to the correct time. This may take up
to 7 minutes.
3. Hang the clock after hands are rapid
advancing.
Note: If the LED does not ash within 30 seconds,
remove the barrel jack plug of the battery pack from
the wireless receiver for 5 seconds and reconnect it.
This resets the receiver. The LED will begin ashing
within 30 seconds.
AC
DC
To
wiring
box

QUICK START INSTALLATION GUIDE SITESYNC IQ®WIRELESS CLOCK SYSTEM
Connect cables to the system controller
A. Connect the GPS antenna to the PREM GPS port.
B. Connect the System Controller power supply to the POWER
INPUT port.
C. Connect campus antenna to the TX ANT port. *Lightning
arrestor must be grounded per local electrical code.
Plug 110v cord into power source. Turn the POWER SWITCH on
the back of the system controller to the on position.
MON MAR 14 2016
10:38:06 AM USCT
American Timel
Status=AUTO GPS=Y
145
Unpack the box
1. Remove the components and system controller from the box.
Save the packing materials in case you need them later.
Check the components
Your system kit comes with:
• System Controller
• Premium GPS receiver with 50' cable & mounting kit (A)
• Power supply (B)
• Campus TX antenna kit (C)
• Installation and Operation Manual
Choose your location
• Choose a location for the GPS receiver outside with a clear
view of the sky. The included mounting bracket allows for
mounting on the side of a building or other structure. The
included set of u-bolts can be used to attach the bracket and
GPS receiver to a mast.
Avoid high voltage equipment and excessive roof overhang
when choosing a location.
• Choose a location for your campus TX antenna either
outside or inside at the highest central location in your facility.
The TX antenna must be located at least 4' away from
the system controller
2
3
Note: If your system controller supports more than one time sync
option, refer to the SiteSync IQ Installation & Operation Manual
for detailed instructions.
TX Ant signal
out to clocks
System controller
located high and central
GPS signal in
Use the Setup Wizard
1. Press 1to start the Setup Wizard (Page 9 in Installation Manual)
2. Create a 4 digit User Lock or enter 0000 to disable this
feature. Press O.Tip: Record this password.
3. Create a 4 digit Service Lock (for advanced features) or enter
0000 to disable this feature. Press O.
Tip: Record this password.
4. Select local time zone by using the <> keys. Press O.
USET=Eastern USCT=Central USMT=Mountain USPT=Pacic
Note: There are 40 options to choose from.
5. Press 8to select automatic DST (Daylight Saving Time) or
0to disable DST if your location doesn't observe DST.
Press O
6. Press 1for 12-hour mode - AM/PM (1:00PM).
Press
2for 24-hour mode - Military (13:00).
7. To conrm proper set up, press 8to sync.
• If successful, “GPS Sync Successful” will display
• If not successful, “GPS Sync Failed” will display. Re-try
by pressing 8again.
8. “Setup Wizard Successfully Completed” will display.
The system controller now shows the correct time and date. You
will no longer be prompted on power-up for setup information.
9. Verify the unit is transmitting. TX should display for about
three seconds every 30 seconds (approximately the top and
bottom of every minute) in the bottom right corner of the
screen.
MON MAR 10 2014
10:38:06 AM USCT
American Time
Status=AUTO TX
Set Menu LOCAL
Time Zone Code: 05
99=Custom USCT
<>=Scroll OK=Accept
Note: Screen
will advance
immediately
A
B
C
To local
power
(110vac)
*See above
To ground