Ameriwood 6421403COM User manual

2Door/1DrawerBaseCabinet
THISINSTRUCTIONBOOKLETCONTAINS IMPORTANT SAFETYINFORMATION.PLEASEREADANDKEEPFORFUTUREREFERENCE.
AssemblyDifficultyMeter
Easy Tough
WARNING:Manufacturerassumesnoliability
forimproperinstallationorexcessiveloads
placedonscrewsorbracket.Thiswallanchor
isnotasubstituteforproperadultsupervision.
SecureYourFurniture
Keepyourhomeandfamilysafe
withthewallanchorkitthatis
includedwiththeproduct.
Seriousorfatalcrushinginjuriescan
occurfromtippingfurniture.

2
‐Openyouritemintheareayouplantokeepittoavoidexcessiveheavylifting.
‐Identify,sortandcountthepartsbeforeattemptingassembly.
‐Compressiondowelsarelightlytappedinwithahammer.
‐Slidesarelabeledwitha
R (right)and L (left)forproperplacement.
‐MakesuretoalwaysfacethepointonthetopoftheCamLocktowardsthe
outeredge.
‐Useallthenailsprovidedforthebackpanelandspreadthemoutequally.
‐Backpanelmustbeusedtomakesureyourunitissturdy.
‐DoNOTuseharshchemicalsorabrasivecleanersonthisitem.
‐Neverpush,pull,ordragyourfurniture.

3
BeforeYouStart

Quick
Tip
Assembly



CamLockFasteningSystem
ThisCamLockFasteningSystemwillbeusedthroughouttheassemblyprocess.
1
3
2
4
Readthrougheachstepcarefullyandfollowtheproperorder
Separateandcountallyourpartsandhardware
Giveyourselfenoughroomfortheassemblyprocess
Havethefollowingtools:FlatHeadScrewdriver,#2PhillipsHead
ScrewdriverandHammer
Caution:Ifusingapowerdrillorpowerscrewdriverforscrewing,
pleasebeawaretoslowdownandstopwhenscrewistight.
Failuretodosomayresultinstrippingthescrew.


4

5
BoardIdentification
Notactualsize
LeftPanel
37367015012
RightPanel
37367015022
Bottom
37367015041
LeftDrawerSide
37368302061
Top
37368015030
DrawerFront
31346403050
RightDrawerSide
37368302071
DrawerBack
37368302080
DrawerBrace
37368000130
DrawerBottom
37368302140
AdjustableShelf
37367015150
Door(x2)
36421403160
BackPanel
K73671500
CE
F
D
GHMN
OP
Q
This piece is paperboard construction.
It is not made from wood, but is
required for the assembly of your unit.
AB

6
BoardIdentification
Notactualsize
This piece is paperboard
construction. It is not made
from wood, but is required for
the assembly of your unit.
A
B
C
D
E
F
G
H
M
N
O
Q
P
P

7
PartList
ActualSize
6
5
4
2
10
1
79
(x8)
#A22620
camlock
(x8)
#A22610
cambolt
(x12)
#A12120
7/16"panhead
(x8)
#A12420
5/8"panhead
(x4)
#A12930
1‐1/8"panhead
(x2)
#A21520
compressiondowel
(x34)
#A21110
nail
(x4)
#A23030
confirmat screw
(x6)
#A11600
1‐1/4"flathead
(x6)
#A17400
8‐32x7/8"truss
(x2)
#A89020
bumper
(x2)
#A11160
5/8"screw
(x4)
#A80250
shelfsupport
16 17 18
3
8

8
PartList
NotActualSize
14a
14b
14c
14d
13
(x1)
#A56100
drawerslide
#A84050
safetybracketkit
14
12
11
(x3)
#A50395
handle (x4)
#A44135
adjustablefoot
15
(x4)
#A65700
hinge

9
STEP1
16
Separatethehingeplatebypressingthehingereleaseattheendofthehingearm.
Removethehingecoverfromthehingearm.
Presstoreleasehingeplate.
hingeplate
hingecover

10
STEP2
2
(x2)
#A22610
2
13 15
(x3)
#A12120
(x1)
#A56100
(x2)
#A65700
15
13
Locatetheslidekit(13).Extendtheslidesasshownandpressthereleaselevertoremovetheinnerslide.Setthe
innerslidesasideforlater.Startbyattachingtheslidestothepanelsattherearoftheslide.Whileslidingthe
middleslidelocatetheholesinthepanelswiththeaccessholeinthemiddleslideandfastenwithscrews(3)as
shown.
inner slide
release lever middle slide
outer slide
use this hole
access holes
2
3
A
use these holes
3

11
STEP3
213 15
(x2)
#A22610
(x3)
#A12120
(x1)
#A56100
(x2)
#A65700
B
15
13
2
3
2
Locatetheslidekit(13).Extendtheslidesasshownandpressthereleaselevertoremovetheinnerslide.Setthe
innerslidesasideforlater.Startbyattachingtheslidestothepanelsattherearoftheslide.Whileslidingthe
middleslidelocatetheholesinthepanelswiththeaccessholeinthemiddleslideandfastenwithscrews(3)as
shown. release lever
inner slide
middle slide outer slide
use these holes
access holes
use this hole
3

12
STEP4
116 17
(x4)
#A22620
(x2)
#A89020
(x2)
#A11160
1
1
Proper orientation of CAM LOCK
Tip
Assembly
Quick
1
1C
D
16
17

13
STEP5
A
B
C
D
UNLOCKLOCK
1st
2nd
(x4)
#A23030
finished edges will face up
8
8
8
8
8

14
STEP6
4512
(x8)
#A12420
(x4)
#A12930
(x4)
#A44135
12
12
5
4
4
A
B
D
Unscrewthetwopiecefootasshown.Aftertoppartof
footisattachedtobottomshelf,screwonbottompartof
foot.Besureallfourarelevelwitheachother.

15
STEP7
Carefully place unit on its front side.
raw surface
Assure that the unit is square.
Distance from corner to corner must be
equal as shown.
Flushtheedgeofthebackpanelwiththe
bottomedgeofthebottomshelf.Alignsquarely
andnailstraightthroughintobackedges.
IMPORTANT! THE BACK PANEL IS A STRUCTURAL PART OF THIS UNIT AND MUST BE INSTALLED PROPERLY.
CAUTION:
When turning unit over to attach back
panel, the slides will slide out.
7
(x34)
#A21110
BD
Q
7

16
STEP8
(x6)
#A12120
3
Inner slide removed from step 2.
3
3
3
3
3
F
G
3

17
STEP9
(x4)
#A22620 Proper orientation of CAM LOCK
Tip
Assembly
Quick
1
1
1
1
1
F
G

18
STEP10
26
(x2)
#A21520
(x4)
#A22610
Approx.
7/16"
6
2
2
2
2
6
6
E
M

19
STEP11
UNLOCKLOCK
F
G
M
E

20
STEP12
9
(x6)
#A11600 9
9
HF
G
N
M
E
9
9
9
9
Insertthedrawerbottom(N)intothegroovein
thedrawersides(F&G).Positionthesmalldrawer
back(H)asshownandattachwithsixscrews(9).