AMP Lighting Estate PendantPro ASI-9006-4036-B-BZ Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® Estate PendantPro Hanging Light
ASI-9006-4036-B-BZ

AMP®Estate PendantPro Hanging Light
ASI-9006-4036-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
Important Safety Instructions
!
This xture is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that
are suitable for outdoor use.
5. The unit low voltage cable should:
a. Be protected by routing in close proximity to the luminaire or tting,
or next to a building structure such as a house or deck;
a. Not be buried except for a maximum 6 inches (15.2 cm) in order to
connect to the main low voltage cable; and
a. Have the length cut off so that it is connected to a connector within
6 inches (15.2 cm) from the building structure, a luminaire, or
tting.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS

[email protected] • 813.978.3900
Product Dimensions
–3–
Package Contents
A. (1) Fixture
B. (1) Fixture Chain
C. (1) Chain Link
D. (1) Mounting Bracket
E. (3) Self-tapping Screws
F. (3) Flat Washers
Parts Required (Sold Separately)
A. (1) LED MR16 Lamp or (1) Bi-Pin
Brass Puck Light
3.15”
8”
13.15” 12.5”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
1
1
AMP®Estate PendantPro Hanging Light
ASI-9006-4036-B-BZ
Remove Shade
Top of Shade
Bottom of Shade
Remove the top of the shade
from the bottom of the shade to
expose the socket.
Two kinds of bulbs are suitable for this xture.
1. MR16 Bulb: Option 1
2. Bi-Pin Brass Puck Light: Option 2
Option 1: MR16 Bulb
Install MR16 Bulb
MR16 Bulb
Socket
Insert the MR16 bulb with the
correct wattage and type marked
on the xture label.
CAUTION: This xture is for LED
use only. Do not exceed maximum
wattage marked on luminaire
label.
NOTE: DO NOT touch MR16 bulb
with bare hands. Use soft cloth to
handle MR16 bulb.
Go to Step 3 to complete
installation.

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
1
2
AMP®Estate PendantPro Hanging Light
ASI-9006-4036-B-BZ
Option 2: Bi-Pin Puck Light
Remove Clips
Screw
Clip
Socket
Remove the clip from the socket
by removing the screws.
Install Bi-Pin Brass Puck Light
Insert the Bi-pin brass puck light
into the socket and secure it
in place with the two screws
previously removed from the clip.
CAUTION: This xture is for LED
use only. Do not exceed maximum
wattage marked on luminaire
label.
NOTE: DO NOT touch the Bi-pin
brass puck light with bare hands.
Use soft cloth to handle the puck
light.
Go to Step 3 to complete
installation.
Socket
Screw
Bi-pin Puck Light

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
3
AMP®Estate PendantPro Hanging Light
ASI-9006-4036-B-BZ
Install Shade
Thread the top of the shade back
onto the bottom of the shade.
Top of Shade
Bottom of Shade
4
Install Mounting Bracket
Wall Anchor
(not included)
Flat
Washer
Self-tapping Screw
Mounting
Bracket
Ceiling Attach the mounting bracket onto
the desired ceiling surface. Secure
with the at washers and self-
tapping screws.
Note: Wall anchors are required
for certain installation conditions
(concrete or brick walls). Mark on
the desired ceiling surface for wall
anchors by using the holes on the
mounting bracket. Remove the
mounting bracket and drill proper
holes on the desired ceiling surface
and then insert the wall anchors.

–6––6–
[email protected] • 813.978.3900
–7–
5
Attach Fixture to Mounting Bracket
Supply Wires Fixture Chain
Fixture Body
Mounting
Bracket
Chain Link
Ceiling Loop
Adjust the xture chain to the desired
length by removing the links if needed.
(Note: Pliers are required for this step).
With the xture chain unattached to the
xture loop on top of the xture body; or
the ceiling loop on the underside of the
mounting bracket, pull the supply wires
through the xture chain alternating
between the links.
After the wires are through the xture
chain, pull the supply wires up and around
the backside of the mounting bracket.
Attach one end of the xture chain to the
xture loop at the top of the xture body.
Lift the xture body and xture chain up
and attach the other end of the xture
chain onto the ceiling loop on the bottom
of the mounting bracket with the chain
link.
The xture will now hang safely. Close the
chain loop at the ceiling loop.

6
Wire Connections
Strip both leads from the luminaire pigtail. Connect the leads from the
luminaire supply cable to the transformer (sold separately).
Fixture Wire
Supply Wire
Wire Connections