AMP Lighting ADL-2010 Series Operating and safety instructions

- 1 -
AMP® LOW VOLTAGE LANDSCAPE LIGHTING
AMP® Deck-DesignPro Classic
ITEM: ADL-2010 Series
INSTALLATION & MAINTENANCE GUIDE
1-813-978-3900 • Mon-Fri 9am-6pm (EST)

IMPORTANT SAFETY INSTRUCTIONS: READ BEFORE INSTALLATION
INSTALLATION & MAINTENANCE GUIDE
!
IMPORTANT SAFETY INSTRUCTIONS
!
AMP® Deck-DesignPro Classic - ADL-2010-X-B-XX
813.978.3900 • [email protected]om • www.amplighting.com
2
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that are suitable
for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or fi ting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
7. If additional lengths of low voltage cable are required, please contact
www.amplighting.com or call 1-813-978-3900.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO
PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning
on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire fitting with a missing or damaged
shield.
SAVE THESE INSTRUCTIONS

PACKAGE CONTENTS
PRODUCT DIMENSIONS
813.978.3900 • [email protected]om • www.amplighting.com
2
813.978.3900 • [email protected]om • www.amplighting.com
3
A. (1) Luminaire
B. (1) Lock Screws
Pro Technique for Hiding Lead Wire
Pro Technique for Hiding Splice Connections
2”
3 3/8”
2 1/4”
Determine the location for the fixture. Drill a hole straight through the
desired mounting location and run the lead wire out the backside of
the location so that the wires are not visible from the front side. Use a
matching trim piece and cut a groove in the back of trim. Cover the
lead wires with the matching trim piece.
All fixtures come with 4’ of lead wire enabling you to hide the splice
connections out of sight. If you must make a splice connection in
view, use an in-line heat shrink style connection that is less visible
than traditional twist caps.

1
WIRE CONNECTION
3
INSTALLATION & MAINTENANCE GUIDE
AMP® Deck-DesignPro Classic - ADL-2010-X-B-XX
813.978.3900 • [email protected]om • www.amplighting.com
4
Remove Lens Assembly
Base
Luminaire Lens Assembly
Rotate the lens assembly counter
clockwise until it is stops and then
lift the lens assembly straight off.
Note: The first time it may be
difficult because the luminaire has
a tight o-ring seal and a grease
sealant for moisture protection.
2
Install Base
Attach the base onto the desired
location and secure with the lock
screws.
Note: Wall anchors are required for
certain installation conditions (e.g.
Brick wall, Concrete Wall, etc.). Mark
on the wall for wall anchors from
the holes on the base. Remove
the base and drill proper holes on
the wall and then insert the wall
anchors.
Wall Anchor
Lock
Screw
Base
Strip both leads from the
luminaire pigtail. Using two wire
connectors (sold separately),
connect the leads from the
luminaire to the main supply
cable leads.
Luminaire
Wire Connector Pigtail
Main Supply Cable

4
5
813.978.3900 • [email protected]om • www.amplighting.com
4
813.978.3900 • [email protected]om • www.amplighting.com
5
Install Bulb
Insert the bulb with correct wattage
and type marked on the luminaire
label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch bulb with bare
hands. Use soft cloth to handle bulb.
Bulb
Socket
Install Lens Assembly
Push the lens assembly back onto
the base aligned with the gaps on
the base. Push hard (moisture proof
fixture requires force to get air out).
Once the lens assembly is flush with
the base, rotate the lens assembly
until it stops and locks into place.
Gap
Inner Shield
Install/Replace Bulb
Rotate the lens assembly and then remove it to expose the bulb
and replace it with the correct wattage and type marked on the
luminaire label. And then reinstall the lens assembly.
IMPORTANT: Halogen bulbs must be protected from moisture and
dust at all times. Always reinstall lens assembly when moved.

INSTALLATION & MAINTENANCE GUIDE
AMP® Deck-DesignPro Classic - ADL-2010-X-B-XX
813.978.3900 • [email protected]om • www.amplighting.com
6

813.978.3900 • [email protected]om • www.amplighting.com 813.978.3900 • [email protected]om • www.amplighting.com
7

Specifications and product details subject to change without notice.
© Copyright 2023, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected]om • amplighting.com
1-813-978-3700 • Mon-Fri 9am-6pm (EST)