AMP Lighting Sol Box Brass ASDL-2014-B-BZ Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Solar Landscape Lighting
AMP® Sol Box Brass
ASDL-2014-B-BZ

AMP®Sol Box Brass
ASDL-2014-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
Important Safety Instructions
!
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and in-
structions may result in serious injury, property damage and void the warran-
t y.
These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situations.
Please note that these solar xtures are equipped with built-in photocells, so
they will not turn on until it is dark enough. These xtures will also require
plenty of sunlight to function properly. It’s best to have the xture in an area
where the sun will get to it at all times throughout the day and where no am-
bient lighting will affect the photocell at night. If your xture is not function-
ing at night, be sure that the on/off button has been engaged. See step one
for details.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Lamp gets HOT quickly!
2. Do not touch the hot lens, guard or enclosure.
3. Keep lamp away from materials that may burn.
4. Do not touch lamp at any time. Use a soft cloth. Oil from skin may dam-
age lamp.
5. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS

[email protected] • 813.978.3900
Product Dimensions
–3–
Package Contents
A. (1) Fixture Body
B. (1) Solar Panel Box
C. (1) Cover Plate
D. (2) Mounting Brackets
E. (4) Screws
F. (4) Wall Anchors
3”
3”
2.25”
2.25”
LUMINAIRE
SOLAR PANEL BOX
4.2”
2.2”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
AMP®Sol Box
ASDL-2014-B-BZ
Test Solar Light
Two installation options are provided. Choose the one according to your
installation environment:
Option 1: Plenty of sunlight.
Option 2: Lack of sunlight.
1
2
Press the ON/OFF switch on
the back of the xture body.
Place the solar light on a
non-abrasive surface with
the solar panel against the
surface to test the xture.
There will be a short delay
for the xture to light up.
The xture will light up when
the solar panel is covered
and turn back off when it is
uncovered.
Now you can proceed to next
steps of installations knowing
the xture is in ON mode.
On/Off Switch
Fixture Body
Non-abrasive Surface

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
1
AMP®Sol Box Brass
ASDL-2014-B-BZ
Install Mounting Bracket
1. Place the mounting bracket onto
the desired location and mark two
points on the wall for the wall
anchors.
2. Remove the mounting bracket. Drill
the proper holes on the marks for
the wall anchors by using an elec-
trical drill.
3. Push the wall anchors into the
drilled holes.
4. Attach the mounting bracket onto
the wall anchors and secure with
the screws. Tighten until snug with
a screwdriver.
WALL SURFACE
Mounting
Bracket
Screw
Wall Anchor
Hole
2
Place Fixture Body on to Mounting Bracket
Attach the bracket on the
back of the xture body to the
mounting bracket on the wall.
WALL SURFACE
Mounting
Bracket
Solar Panel Box
Fixture Body
INSTALLATION OPTIONAL 1

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
AMP®Sol Box Brass
ASDL-2014-B-BZ
INSTALLATION OPTIONAL 2
Solar Panel Box
PLENTY OF SUNLIGHT
LACK OF SUNLIGHT
Fixture Body Max. 8.5”
If the luminaire is going to be installed in a location where there is low
sunlight, make sure it is still close to an area where there is plenty of
sunlight for the solar panel to be installed separately.
Note: This distance must be less then 8.5 inches.
1
Install Mounting Bracket
1. Drill a .90” round hole through
the desired mounting location.
2. Place the mounting bracket above
the hole and mark two points on
the wall using the two mounting
bracket holes as guides.
3. Remove the mounting bracket and
drill proper holes on the marks
for the wall anchors using an
electrical drill.
4. Push the wall anchors into the
drilled holes.
5. Attach the mounting bracket
onto the wall anchors and secure
with screws. Tighten using a
screwdriver.
WALL SURFACE
Mounting
Bracket
Screw
Wall Anchor
.90” Hole
Hole

–6––6–
[email protected] • 813.978.3900
–7–
2
Remove Solar Panel Box from Fixture Body
Slide the solar panel box off the top of the xture body to remove it.
Solar Panel Box
Fixture Body
3
Disconnect Quick Connector
Disconnect the quick connector to
separate the male connector from
female connector.
Female connector
Male connector
4
Install Cover Plate
Insert the cover plate onto the top
of the xture body.
Cover Plate
Fixture Body

INSTALLATION & MAINTENANCE GUIDE
AMP®Sol Box Brass
ASDL-2014-B-BZ
5
Install Fixture Body onto Mounting Bracket
Go to step 1 to install another mounting bracket onto the sunlit area for
the solar panel. Pull the female connector to the other side then go the
step 6.
Pass the female connector and
wire through the hole. Place
the bracket on the back of the
xture body onto the mounting
bracket.
WALL SURFACE
Mounting
Bracket
Fixture Body
.90” Hole
Female connector
Wire
6
Connect Quick Connector
Insert the female connector
into the male connector and
secure the cap to tighten the
quick connector.
Female connector
Male connector
–8–
www.amplighting.com
–8–

7
Install Solar Panel Box on to Mounting Bracket
Carefully tuck the quick connector
and wire inside of the hole. Place
the bracket of the solar panel box
onto the mounting bracket.
WALL SURFACE
Mounting
Bracket
Wire
Hole
Quick connector
Solar Panel Box
[email protected] • 813.978.3900
–9–

Install Solar Panel Box on to Mounting Bracket
INSTALLATION & MAINTENANCE GUIDE
AMP®Sol Box Brass
ASDL-2014-B-BZ
Solar Panel Box
Quick Connector
Cover Screw
Battery Pack
1. Using a screwdriver, remove the screws from the cover of the solar
panel box.
2. Disconnect the quick connector.
3. Remove the battery pack out of the solar panel box and replace it
with a new one.
4. Connect the quick connector to the new battery pack and place
the cover back onto the solar panel box. Secure it with previously
removed screws.
–10–
www.amplighting.com
–10–