AMP Lighting VariantPro AAL-1028-0-B-BZ Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® Zero- Lead Wire System VariantPro Downlight
AAL-1028-0-B-BZ

AMP®Zero- Lead Wire System VariantPro Downlight
AAL-1028-0-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
Important Safety Instructions
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS

[email protected] • 813.978.3900
Product Dimensions
–3–
Package Contents
A. (1) Fixture Body
B. (1) Integrated Hub Top
1”
0.75”
2.83”
2.3”
5.8”
2.5”
There are two types of mounts that are sold separately for this xture; the,
Surface Mount and the Tripod Mount. Both must be used with this xture in
a downward orientation.

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
2
1
AMP®Zero- Lead Wire System VariantPro Downlight
AAL-1028-0-B-BZ
Wire Connection
Install Surface Mount
Option1: Surface Mount
Integrated Hub Top
Main Supply Wires
Fixture Wires
Connectors
Surface Mount
Main Supply Wire
Main Supply Wire
Continuation
Insert the main supply wire continuation (if needed) and the main
supply wire up through the bottom of the surface mount and strip the
ends of both sets of supply wires.
Attach the xture wires and both sets of the main supply wires to their
correct connectors in the integrated hub top.
Once the wires are installed properly, thread the integrated hub top
back onto the surface mount and hand tighten until snug.
Screw
Optional Anchor
Surface Mount
Washer
Place the surface mount onto the
desired location and secure it with
the screws. Tighten with a screw-
driver. Nylon spacers are required
when installing on trees.

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
2
1
AMP®Zero- Lead Wire System VariantPro Downlight
AAL-1028-0-B-BZ
Install Tripod Mount
Wire Connection
Option 2: Tripod Mount
Integrated Hub Top
Main Supply Wires
Fixture Wires
Connectors
Tripod Mount
Main Supply Wire
Main Supply Wire
Continuation
Insert the main supply wire continuation (if needed) and the main sup-
ply wire up through the bottom of the tripod mount and strip the ends
of both sets of supply wires.
Attach the xture wires and both sets of the main supply wires to their
correct connectors in the integrated hub top.
Once the wires are installed properly, thread the integrated hub top
back onto the tripod mount and hand tighten until snug.
Screw
Optional
Anchor
Tripod Mount
Washer
Place the tripod mount onto the de-
sired location and secure it with the
screws. Tighten with a screwdriver.
Nylon spacers are required when
installing on trees.

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
1
AMP®Zero- Lead Wire System VariantPro Downlight
AAL-1028-0-B-BZ
Remove Glare Guard and Lens
Bulb Installation
Loosen the lens and the set
screw and remove the glare
guard.
Lens
Glare Guard
Set Screw
2
Insert the bulb with the correct
wattage and type marked on the
luminaire label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch bulb with bare
hands. Use soft cloth to handle
bulb.
Socket
Bulb
Install Bulb

–6––6–
[email protected] • 813.978.3900
–7–
3
Install Lens and Glare Guard
Thread the lens onto the xture
body and hand tighten.
Then, place the glare guard onto
the lens and secure with the previ-
ously removed set screw.
Lens
Set Screw
Glare Guard
Fixture Body

IS-AAL-1028-0-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2019, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com