AMP Lighting APL-3024-4-B-BZ Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® 12V Mini PilotPro Bollard
APL-3024-4-B-BZ

AMP®12V Mini PilotPro Bollard
APL-3024-4-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
Important Safety Instructions
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS

[email protected] • 813.978.3900
Product Dimensions
–3–
Package Contents
A. (1) Fixture Body
B. (1) Coupler
Two installation options are available for this xture.
1. Stake mount (option 1): Step 1 - Step 2, then go to Step 4.
2. Surface mount (option 2): Step 3, then go to Step 4.
23.75”
4.72”
7.1”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
2
1
AMP®12V Mini PilotPro Bollard
APL-3024-4-B-BZ
Install Stake
Install Fixture Body to Stake
Stake Mount (Option 1)
Board
Ground
Soil
Stake
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until ange of stake is
ush to grade. To avoid damage
to the stake, place a board on
top of the stake while hammer-
ing.
Note: If the ground is hard and
the stake is difcult to install,
make a crosscut in the ground
using a at shovel.
Fixture Body
CouplerFixture Wire
Ground
Stake
Pass the xture wire through
the coupler and the center hole
of the stake. Thread the xture
body, the coupler and the stake
together. Hand tighten until
snug.

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
3
4
AMP®12V Mini PilotPro Bollard
APL-3024-4-B-BZ
Install Fixture Body with Self-tapping Screws
Wire Connections
Surface Mount (Option 2)
Self-tapping
Screw
Anchor
Base
Concrete or Brick
Fixture Body
Ground
Place the xture body on the
desired location and make three
marks on the ground using the
holes on the base.
Remove the xture body and
drill proper holes into the
ground.
Insert the anchors into the
drilled holes, then place the
base of the xture body onto
the anchors and secure by
threading self-tapping screws
into anchors. Hand tighten with
a screwdriver.
Pigtail
Main Supply Cable
Supply Wire from
Fixture Body
Wire Connectors
Strip both leads from xture body. Using two wire connectors (sold
separately), connect the leads from the xture body to the main supply
cable leads.

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
5
AMP®12V Mini PilotPro Bollard
APL-3024-4-B-BZ
Remove Fixture Top
Rotate the xture top and
remove it from the xture
body.
Rotate
Fixture Top
6
Install Lamp
Insert the lamp with correct
wattage and type marked on
the xture label and secure
tightly into place.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
Lamp
Socket

–6––6–
[email protected] • 813.978.3900
–7–
Install/Replace Lamp
7
Install Fixture Top
Thread the xture top back
onto the xture body. Hand
tighten until snug.
Fixture Body
Rotate
Fixture Top
Please reverse Step 5 - Step 7 to expose the lamp and replace it with the
correct wattage and type marked on the xture label. And then reinstall
the xture top.
IMPORTANT: Lamp must be protected from moisture and dust at all times.
Always reinstall the xture top when removed.

IS-APL-3024-4-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2019, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com