AMP Lighting SleekPro MR11 Downlight Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® SleekPro MR11 Downlight (Lamp Ready)
AAL-1034-B-BZ

AMP®SleekPro MR11 Downlight (Lamp Ready)
AAL-1034-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
Important Safety Instructions
!
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and in-
structions may result in serious injury, property damage and void the warran-
t y.
These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply (trans-
former) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and UL listed wire connector so that it is
located within 6 inches (15.2 cm) from a building structure, a luminaire
or tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may dam-
age lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS

[email protected] • 813.978.3900
Product Dimensions
–3–
Package Contents
A. Fixture Body
B. Tool
Parts Required (sold separately)
A. Mounting Accessory
B. (1) MR11 Bulb
1.65”
5”
3.75”
2.1”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
2
1
AMP®SleekPro MR11 Downlight (Lamp Ready)
AAL-1034-B-BZ
Remove Glare Guard and Lens
Loosen the set screw and remove
the glare guard.
Then twist and remove the lens
from the xture body.
Fixture Body
Lens Set Screw
Glare Guard
Insert the MR11 bulb with the
correct wattage and type marked
on the xture label.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
MR11 Bulb
Socket
Install MR11 Bulb
3
Install Lens and Glare Guard
Fixture Body
Lens
Set Screw
Glare Guard
Thread the lens back onto the
xture body and hand tighten
until snug.
Place the glare guard back onto
the lens and secure by using the
previously removed set screw.

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
4
5
AMP®SleekPro MR11 Downlight (Lamp Ready)
AAL-1034-B-BZ
Install Fixture Body to Mount
Fixture Body
Pass the supply wire through the mount and thread the mount onto
the xture body.
Tighten the lock nut against the mount and hand tighten until snug.
Supply Wire
Mount
Lock Nut
Install Mount
Attach the mount onto the
surface using 3 self-tapping
screws.
Supply Wire
Tree
Base
Self-tapping Screw

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
6
Wire Connections
AMP®SleekPro MR11 Downlight (Lamp Ready)
AAL-1034-B-BZ
Strip both leads from the luminaire pigtail. Using two UL listed wire
connectors (sold separately), connect the leads from the luminaire to
the main supply cable leads.
Main Supply Cable
UL Listed
Wire Connectors
Fixture Pigtail
7
Adjust Fixture Direction
Using an Allen wrench, loosen the
knuckle and adjust the xture to
your desired direction. Once your
desired direction is achieved,
tighten the knuckle to secure it
in place.
ROTATE
Glare Guard
Allen Wrench
Knuckle

–6––6–
[email protected] • 813.978.3900
–7–
Install/Replace Bulb
Remove the glare guard and the lens to expose the MR11 bulb and replace it
with the correct wattage and type marked on the xture label. Then,
reinstall the lens and the glare guard.
IMPORTANT: MR11 bulb must be protected from moisture and dust at all
times. Always reinstall the lens and the glare guard when removed.

IS-AAL-1035-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2021, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com