AMP Lighting VAL-91 Series Operating and safety instructions

Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP®Downlight
VAL-91xx and AWL-91xx series

AMP®ControlPro™ 200 LED Downlight (Constant Output)
VAL-91xx-25-BBZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation, operation
maintenance or mounting situation.
1. Make sure that the power is turned OFF before installing or servicing this
luminaire.
2. Warning: risk of electrical shock. Install all luminaires 10 feet (3.05M) or
more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with wire connectors that is suitable for
outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire, or tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm)
7. If additional lengths of low voltage cable is required, please contact www.
AMPlighting.com or call 1-813-978-3900.
SAVE THESE INSTRUCTIONS
Important Safety Instructions: Read Before Installation
!

–3–
Package Contents
Product Dimensions
A. (1) Luminaire
B. (1) Base
C. (3) Spacer
D. (3) Self-tapping Screw
E. (2) Optics*
* Ships with a 60° (installed) optic.
Install Base
Determine desired location for mounting
luminaire. Pass self-tapping screws through
holes on the base and spacers. Thread self-
tapping screws into surface to secure the
base.
NOTE: Wall anchors (not supplied) are
required for brick walls or concrete walls.
To determine locations for wall anchors by
placing the base onto your desired location
and mark points from holes on base.
6 1/2”
6 3/4”
8 3/4”
3 1/4”
5”
Base
Self-tapping
Screw
Wall Anchor
(Optional,
not supplied)
Spacer
1

AMP®ControlPro™ 200 LED Downlight (Constant Output)
VAL-91xx-25-BBZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–4–
Install Luminaire to Base
Wire Connection
2
3
Place luminaire on top of base and
secure with lock collar. Tighten until
snug.
Luminaire
Pigtail
Base Lock Collar
Strip both leads from luminaire pigtail. Using two wire connectors,
(sold separately) connect the leads from luminaire to main low voltage
supply cable leads.
Pigtail
Main Low Voltage
Supply Cable
Wire Connectors

–5–
Remove Glare Guard
Remove Outer Ring
Replace Optic
4
5
6
Unscrew lock screw and remove glare
guard from luminaire.
Unscrew the lens and remove it from
the luminaire.
Remove plug at the center of
optic. Unscrew the screw and remove
the optic from luminaire.
Put new optic to luminaire. Reverse
Steps 6 and Step 4 to reinstall
removed parts.
Install/Replace Optic
Glare Guard
Lens
Optic
Plug
Screw
Lock Screw
Luminaire
Luminaire
Luminaire

is-aal-91xx-ver7.pdf
Specications and product details subject to change without notice.
© Copyright 2017, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com