AMP Lighting AtomPro Mini LED Spotlight Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® AtomPro Mini LED Spotlight (Constant Output)
AAL-1041-4-B-BZ

AMP® AtomPro Mini LED Spotlight (Constant Output)
AAL-1041-4-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
[email protected] • 813.978.3900
Product Dimensions
–3–
1
Important Safety Instructions: Read Before Installation
!
Important Safety Instructions
!
Package Contents
A. (1) Fixture Body
Parts Required (sold separately)
A. (1) Stake
Install Stake
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that
are suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn o/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
1.15”
1.75”
2.2”
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until ange of stake
is ush to grade. To avoid
damage to the stake, place a
board on top of the stake while
hammering.
Note: If the ground is hard and
the stake is dicult to install,
make a crosscut in the ground
using a at shovel.
Board
Ground
Soil
Stake

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
2
[email protected] • 813.978.3900
–5–
AMP® AtomPro Mini LED Spotlight (Constant Output)
AAL-1041-4-B-BZ
Install Fixture Body to Stake
Clear away an area in the
ground at the wireway slot
on top of the stake. Lay the
xture wire into the wireway
slot. Thread the xture body
onto the stake and hand
tighten until snug.
Fixture Body
Fixture Wire
Ground
Soil
Stake
3
Wire Connections
Strip both leads from the xture body supply wires. Using two UL listed
wire connectors (sold separately), connect supply wires from xture
body to the main supply cable leads.
Main Supply Cable
Supply Wire from
Fixture Body
Wire Connectors
4
Adjust Luminaire Direction
Loosen the handle at the joint
of xture body and then adjust
the luminaire to your desired
direction. Always tighten the
handle once your desired
direction is achieved.
Knuckle
Luminaire
Rotate
Rotate

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
[email protected] • 813.978.3900
–7–
AMP® AtomPro Mini LED Spotlight (Constant Output)
AAL-1041-4-B-BZ

IS-AAL-1041-4-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2021, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com