AMP Lighting EscherPro MR11 Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® EscherPro MR11 Lanai Light Brass Black
AAL-1046-B-BK

AMP®EscherPro MR11 Lanai Brass Black
AAL-1046-B-BK
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
Important Safety Instructions
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the war-
ranty.
These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this xture.
2. Warning: this xture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply (transform-
er) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm) in
order to connect to the main low voltage cable.
5. Wiring connections must be made with UL Listed wire connectors that
are suitable for the application.
6. Position the wire connector so that it is located within 6 inches (15.2
cm) from a building structure, a luminaire, or tting.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.

[email protected] • 813.978.3900
Parts Required (Sold separately)
–3–
Package Contents
A. (1) Fixture
B. (2) Anchors
C. (2) Screws
D. (1) Allen Wrench
Product Dimensions
A. (1) MR11 Lamp
3.89”
1.82”
3.08”
1.04”
2.95”
1.82”
1.58”
2.57”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
2
1
AMP®EscherPro MR11 Lanai Brass Black
AAL-1046-B-BK
Remove Glare Guard
Loosen the thumb screw to
remove glare guard from the
xture body.
Thumb Screw
Fixture Body
Glare Guard
Remove Lens
Fixture Body
Rotate the lens counter-clockwise
and remove it from the xture
body.
Lens
3
Install MR11 Lamp
Insert MR11 Lamp with correct
wattage and type marked on
xture label.
CAUTION: Do not exceed
maximum wattage marked on
luminaire label.
MR11 Lamp
Socket

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
4
5
AMP®EscherPro MR11 Lanai Brass Black
AAL-1046-B-BK
Install Lens
Fixture Body
Lens
Place the lens back onto the
xture body and rotate it
clockwise to lock it in place.
Install Glare Guard
Thumb Screw
Fixture Body
Glare Guard
Place the glare guard back
onto the xture body and
secure with previously
removed screw.
6
Adjust the glare guard direction
Rotate
Knuckle Screw
Allen
Wrench Glare Guard
Loosen the knuckle screw
at the joint and rotate the
glare guard until there is
enough space for next step.
Tighten the screw once
the glare guard direction is
achieved.

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
7
AMP®EscherPro MR11 Lanai Brass Black
AAL-1046-B-BK
Install Fixture Body
Determine the desired location
for the xture. Mark points on
the desired location from the
holes on the backplate of the
xture body.
Remove the xture body, drill
holes from the marks and insert
anchors completely.
Pull the supply wire out of the
backplate from the slot on the
bottom. Place the backplate of
xture body over the anchors and
secure with screws. Hand tighten
with a screwdriver.
Screw
Anchor
Mark
WALL
Fixture Body
Fixture Wire
Slot
8
Wire Connection
Strip two leads from the xture
wires. Using two UL listed wire
connectors (not provided), con-
nect leads from xture wires to
main supply cable leads.
Main Supply Cable
Fixture Wires
Wire Connectors

–6––6–
[email protected] • 813.978.3900
–7–
9
Adjust Glare Guard Direction
Rotate
Screw
Allen
Wrench
Glare Guard
Loosen the knuckle screw at
the joint and rotate the glare
guard to the desired direction.
Tighten the knuckle screw
once the glare guard direction
is achieved.
Install/Replace MR11 Lamp
Please reverse Step 3 - Step 5 to expose the MR11 lamp and replace it
with correct wattage and type marked on xture label. And then reinstall
the lens and glare guard.

IS-AAL-1046-B-BK-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2022, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com