AMP Lighting HydraPro AWL-5006-B-BZ Operating and safety instructions

INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com
AMP®Low Voltage Landscape Lighting
AMP® HydraPro MR11 In-Grade Light
AWL-5006-B-BZ

AMP®HydraPro MR11 In-Grade Light
AWL-5006-B-BZ
INSTALLATION & MAINTENANCE GUIDE
www.amplighting.com
–2–
Important Safety Instructions: Read Before Installation
!
Important Safety Instructions
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
This xture is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation, oper-
ation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing
this xture.
2. Warning: this xture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply (trans-
former) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm)
in order to connect to the main low voltage cable.
5. Wiring connections must be made with UL listed wire connectors that
are suitable for the application.
6. Position the wire connector so that it is located within 6 inches (15.2
cm) from a building structure, a luminaire, or tting.

[email protected] • 813.978.3900
Product Dimensions
–3–
Package Contents
A. (1) Fixture Body
Parts Required (Sold Separately)
A. (1) MR11 Lamp
2.75”
2.85”

INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
2
1
AMP®HydraPro MR11 In-Grade Light
AWL-5006-B-BZ
Remove Faceplate
Use a screwdriver to loosen the
screws on the faceplate and
remove the lens from the xture
body.
Faceplate
Lens
Screw
Fixture Body
Install Lamp
Insert the lamp with the correct
wattage and type marked on the
xture label and push rmly into place.
CAUTION: Do not exceed maximum
wattage marked on xture label.
Socket
MR11 Lamp
3
Install Faceplate
Place the lens and the faceplate
back onto the xture body and
secure the removed screws in a
star pattern using a screwdriver.
Tighten until snug.
Lens
Faceplate
Screw
Fixture Body

[email protected] • 813.978.3900
–5–
INSTALLATION & MAINTENANCE GUIDE
4
5
AMP®HydraPro MR11 In-Grade Light
AWL-5006-B-BZ
Dig Hole
Hole
Soil
3”
3”
3”
Prepare a hole in the ground.
Make sure there are approxi-
mately 3” spaces surrounding
the xture for pea gravel or
sand.
Wire Connection
Strip both leads from the luminaire pigtail. Using two wire connectors
(sold separately), connect the leads from the xture body to the main
supply cable leads.
Pigtail
Main Supply Cable
Supply Cables Wire Connectors

INSTALLATION & MAINTENANCE GUIDE
–6–
www.amplighting.com
–6–
6
AMP®HydraPro MR11 In-Grade Light
AWL-5006-B-BZ
Fill Hole
Install the xture in the hole
and ll the hole with pea
gravel or sand.
Pea Gravel
or Sand
Soil
Fixture

–6––6–
[email protected] • 813.978.3900
–7–
Install/Replace Glare Guard
7
Remove Faceplate
Use a screwdriver to loosen the
screws on the faceplate and
remove the lens from the xture
body.
Faceplate
Lens
Screw
Fixture Body
8
Replace Faceplate
Place the lens and faceplate onto
the xture body and secure with
previously removed screws in a
star pattern. Hand tighten until
snug with a screwdriver.
Faceplate
Lens
Screw
Fixture Body
Option 1 Option 2
Faceplate Replacement Options
Option 3 Option 4
Install/Replace Lamp
Repeat step 1 - step 3 to remove the faceplate and expose the lamp.
Replace it with the correct wattage and type marked on the xture label.
Then, reinstall the faceplate.
IMPORTANT: Lamps must be protected from moisture and dust at all
times. Always reinstall the faceplate when removed.

IS-AWL-5006-B-BZ-ver1.pdf
Specications and product details subject to change without notice.
© Copyright 2020, AMP®Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com