AMP Lighting MR16 HydraPro Operating and safety instructions

AMP®Low Voltage Landscape Lighting
AMP®MR16 HydraPro™ In-Grade Light (Lamp Ready)
AWL-703-25-BBZ
INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com

AMP®MR16 HydraPro™ In-Grade Light (Lamp Ready)
AWL-703-25-BBZ
Important: Please Read Before Installation
Important: Safety Instructions
INSTALLATION & MAINTENANCE GUIDE
This xture is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure that the power is turned OFF before installing or servicing this
xture.
2. Warning: this xture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm) in
order to connect to the main low voltage cable.
5. Wiring connections must be made with wire connectors that are suitable
for outdoor use.
6. Position the wire connector so that it is located within 6 inches (15.2
cm) from a building structure, a luminaire, or tting.
LIGHTED LAMP IS HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.
!
!
www.amplighting.com
–2–

[email protected] • 813.978.3900
Product Dimensions
–3–
Package Contents
Parts Required (sold separately)
A. (1) Fixture
B. (1) Stake
A. (1) MR16
4.25”
4”

AMP®MR16 HydraPro™ In-Grade Light (Lamp Ready)
AWL-703-25-BBZ
INSTALLATION & MAINTENANCE GUIDE
–4–
www.amplighting.com
–4–
Removing the Faceplate
1
Unlock the screws and remove the
faceplate, gasket, and lens from the
housing.
Gasket
Faceplate
Lens
Housing
Screw
Install/Replace Bulb
2
Insert the bulb with the correct
wattage and type marked on the xture
label.
CAUTION: Do not exceed maximum
wattage marked on luminaire label.
NOTE: DO NOT touch bulb with bare
hands. Use a soft cloth to handle bulb.
MR16 Bulb
Socket

[email protected] • 813.978.3900
–5–
Install Lens and Faceplate
3
Place the lens, gasket, and faceplate back
onto the housing. Secure them with the
screws previously removed. Hand tighten
until snug, then use a srewdriver to secure
them in a star pattern.
Screw
Housing
Lens
Faceplate
Gasket
Install Stake
4
Determine the desired location for
mounting the xture. Hammer the stake
into the ground until ange of stake is ush
to grade. To avoid damage to the stake,
place a board on top of the stake while
hammering.
NOTE: If the ground is hard and the stake
is difcult to install, make a crosscut
in the ground using a at shovel before
hammering the stake.
Board
Stake
Soil
Ground

–6–
www.amplighting.com
–6–
Wire Connection
6
Strip both leads from the luminaire pigtail. Using two wire connectors
(sold seperately), connect the leads from the luminaire to the main
supply cable.
Pigtail
Main Supply Cable
Wire Connectors
AMP®MR16 HydraPro™ In-Grade Light (Lamp Ready)
AWL-703-25-BBZ
INSTALLATION & MAINTENANCE GUIDE
Install Fixture to Stake
5
Clear away an area in the ground at the
wireway slot on top of the stake. Lay
the luminaire pigtail into the wireway
slot and screw the xture onto the
stake. Tighten until snug.
Fixture
Stake
Pigtail
Wireway Slot

[email protected] • 813.978.3900
–7–
Remove Ring
7
Loosen the screws and remove the
faceplate from the housing.
Screw
Faceplate
Housing
Install/Replace Glare Guard
Install Glare Guard
8
Attach the glare guard onto the
housing and secure with the screws
previously removed.
Housing
Screw
Glare Guard

is-AWL-703-BBZ-ver5.pdf
Specications and product details subject to change without notice.
© Copyright 2018, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com