AMP Lighting ONE HydraPro AWL-700IR-25-BBZ Operating and safety instructions

AMP®Low Voltage Landscape Lighting
AMP ONE®HydraPro™ LED In-Grade Light (Dimmable)
AWL-700IR-25-BBZ
INSTALLATION & MAINTENANCE GUIDE
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com

AMP ONE®HydraPro™ LED In-Grade Light (Dimmable)
AWL-700IR-25-BBZ
Important: Please Read Before Installation
Important: Safety Instructions
INSTALLATION & MAINTENANCE GUIDE
This xture is intended for installation in accordance with local codes and the
National Electric Code (NEC). Failure to adhere to these codes and instruc-
tions may result in serious injury, property damage and void the warranty.
These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situation.
1. Make sure that the power is turned OFF before installing or servicing this
xture.
2. Warning: this xture is not intended to be installed within 10 feet [3
meters] of a pool, spa or fountain.
3. This xture is intended to be used only with a power supply (transform-
er) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Underground Low Energy Cable must not be buried over 6” (15.2 cm) in
order to connect to the main low voltage cable.
5. Wiring connections must be made with wire connectors that is suitable
for outdoor use.
6. Position the wire connector so that it is located within 6 inches (15.2
cm) from a building structure, a luminaire, or tting.
7. IR dimmability with our Design-Master™ Remote Control.
LIGHTED LAMP IS HOT!
WARNING – TO REDUCE THE RISK OF FIRE OR INJURY TO PERSONS.
1. Turn o/unplug and allow to cool before reducing lamp.
2. Lamp gets HOT quickly!
3. Do not touch the hot lens, guard or cowl.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time.
6. Use a soft cloth.
7. Oil from skin may damage lamp.
8. Do not operate the xture with a damaged or missing lens or shield.
!
!
www.amplighting.com
–3–
[email protected] • 813.978.3900

[email protected] • 813.978.3900
Product Dimensions
–4–
INSTALLATION & MAINTENANCE GUIDE
–5–
www.amplighting.com
–5–
Package Contents
Parts Required (Sold Separately)
A. (1) Fixture
B. (1) Stake
A. (1) AMP®ONE Design-Master
Remote ControlTM
2”
4”
Install Stake
1
Board
Stake
Soil
Ground
Install Fixture to Stake
2
Fixture
Stake
Pigtail
Determine desired location for mounting
the xture. Hammer stake into ground until
ange of stake is ush to grade. To avoid
damage to stake, place a board on top of
the stake while hammering.
NOTE: If ground is hard and the stake
is dicult to install, make a crosscut
in ground using a at shovel before
hammering the stake.
Clear away area in ground for the
stake. Lay the luminaire pigtail into the
cleared area and screw the xture into
the stake. Tighten until snug.
AMP ONE®HydraPro™ LED In-Grade Light (Dimmable)
AWL-700IR-25-BBZ

[email protected] • 813.978.3900
–6–
Remove Faceplate
4
Unscrew screws and remove the
faceplate from the xture.
Screw
Faceplate
Fixture
Install Glare Guard
5
Attach the glare guard onto the
xture and secure it with the
screws previously removed.
Fixture
–7–
www.amplighting.com
–7–
Wire Connection
3
Pigtail
Main Supply Cable
Wire Connectors
Install/Replace Glare Guard
Screw
Glare Guard
Strip both leads from luminaire pigtail. Using two wire connectors
(sold seperately), connect leads from luminaire to main supply cable.

is-AWL-700IR-BBZ-ver5.pdf
Specications and product details subject to change without notice.
© Copyright 2017, AMP® Lighting, Lutz FL USA 33549 • All rights reserved.
[email protected] • 813.978.3900
Help Hotline:
1-813-978-3900 • Mon-Fri 9am-6pm (EST)
www.amplighting.com