Setting up the Orchestra
User conguration:
On startup, the ORC50 tactile screen will display the
User page. The rst time you use the ORC50, you
will have to create a new user.
1/ Press the New User button on the tactile screen
2/ Name the new user as required and press the
[OK] button to validate your choice. Press [OK] to
skip password creation.
3/ On the User page, choose the user you just
created, and press the [OK] button. The ORC50 will
display its default menu screen.
System conguration:
The ORC50 System Conguration page lets you
adjust properties like the IP address of the ORC50.
1/ Press System on the tactile screen. The
Network Conguration tab will be displayed.
2/ Select the Lan Settings option, rotate the
corresponding knobs to change the IP address
of the ORC50 (IP1,2,3,4) or press the <Default>
button to restore the address to 192.168.0.15.
Press the [OK] button to validate
3/ Press [OK] again to Exit the system page.
Show conguration:
When starting with the ORC50, you will need to
create a new show.
1/ Press the Shows button on the tactile
screen then “Create a New Show” button.
2/ The ORC50 will display the Show Edit
Name screen, you can now enter a new name.
Choose a name for your show, then press the
[OK] button to validate your choice.
3/ The ORC50 will display a blank show page.
Conguring the show
To run a show, follow these few steps:
Screen setup:
1/ Select a Screen in the Screen section of the ORC50
by pressing one of the six available buttons. The
Screen page will appear on the ORC50 tactile screen.
2/ Press Screen Setup on the tactile screen.
3/ On the <Screen Setup>, select the slave device
type and mode. Press Edit to rename your screen.
4/ Press Edit Devices. Add Device. Using the
tactile screen, Congure the communication
settings of the device that the ORC50 will control.
5/ Press the [OK] button to validate your
changes. The ORC50 will begin connecting to
the congured device.
6/ Press the [OK] button to return to the Screen
Setup page.
Output conguration:
1/ In the Screen Setup page, press Edit
Outputs and select the output, Main or
Preview, you wish to adjust, then congure the
output format (resolution), output rate, output
type required.
2/ Press Pattern, and select an available
pattern to check your output settings on
screen. Press Pattern again, and select None
to revert to your image on screen.
3/ Press the [OK] button to return to the screen
setup page.
Input conguration:
1/ In the Screen Setup page, press Edit Input, you
can manually congure each input by selecting it and
then select the input you wish to work on, the type of
plug, the signal type or press the [AUTOSETTING]
button, for an automatic setup of your inputs.
2/ Press [OK]button.
Soft Edge setup:
Please refer to the Soft Edge Setup Chapter of
the User manual.
Image settings:
In the screen setup page, to access source
image settings, press the [IMAGE SETTINGS]
button.
Logos & Frames conguration:
1/ In the screen setup page, press the [LOGOS/
FRAMES] button.
2/ Select a source you wish to use as a logo or
frame.
3/ Choose the memory slot to save the Logo/Frame
into, edit size, position with the joystick, and the
keying settings by rotating the approriate knobs.
4/ Press [STORE] to store your logo or frame.
Rear Panel Description
100-250 VAC 2A 50-60Hz
RJ-45 connector: Connect the Orchestra to
10/100 Ethernet LAN using this female RJ-45
connector: used to control switcher
Not in use
Clone of the tactile screen
For installation
Serial port (not in use)
DC
RJ-45
RJ-45 - Auxiliary
Auxiliary display output
Mounting Bar
RS-232
