Zennio MAXinBOX66 Guide

Technical Documentation
© Zennio Avance y Tecnología S.L. Edition 3 Further information www.zennio.com Page. 1/ 2
MAXinBOX66
MAXinBOX66. Multi-function actuator 6 outputs 16A and 6 A/D inputs
ZN1IO-MB66 Technical Documentation
FEATURES
DIN rail unit assembly (EN 50022), with snap fit clamp.
Size 67 x 90 x 80 mm (4.5 DIN units).
KNX BCU integrated.
3 different configurable channels(*):
shutter channels (up to 3)
individual outputs (up to 6)
6 analog/digital inputs.
Manual output operation with push button and
LED status indicator.
Logical functions included.
Output timing facilities.
Total data saving on power failure.
Suitable for capacitive loads, maximum 140 µF.
Possibility to connect different phases in adjoining
outputs.
CE directives compliant.
GENERAL SYSTEM SPECIFICATIONS
CONCEPT
DESCRIPTION
Type of device
Electric operation control device
KNX supply
Voltage
29VDC SELV
Voltage range
21…31VDC
Power consumption
240 mW (max)
Bus connection
Typical bus connector TP1, 0.50 mm² section
External power supply
No
Ambient temperature
from 0ºC to +55ºC
Storage temperature
from -20ºC to +70ºC
Ambient humidity
30 to 85% RH (no condensation)
Storage humidity (relative)
30 to 85% RH (no condensation)
Complementary characteristics
Class B
Safety class
II
Operation type
Continuous operation
Device action type
Type 1
Electrical solicitations period
Long
Type of protection
IP20, clean environment
Assembly
Independent control assembly device to be mounted inside of electrical panels with
DIN rail (EN 50022).
KNX bus failure response
Data saving and relays open if channel configured as a shutter.
Response when restarting KNX bus
Data recovering and output status change according to programming when
recovering.
Operation indication
Programming LED indicates programming mode (red) and test mode (green). Output
status LED indicators reflect current output state.
Weight
200 gr.
PCB CTI index
175 V
Enclosure
PC+ABS FR V0 halogen free
Programming/test button: short button press to set the programming mode. If this button is held while plugging the device into the KNX bus, it goes
into safe mode. If this button is held more than 3 seconds, the device goes into manual mode (test mode)
LED: programming mode indicator (red). When the device goes into safe mode, it blinks (red) every half second. The manual mode is indicated by the
green color. During start up (after reset or power failure) and if the device is not in safe mode, LEDs indicators blink blue for a few seconds
1. Analog/Digital inputs
2. Upper outputs
3. Output status LED indicator
4. Output control button
5. Programming/Test LED
6. Lower outputs
7. KNX connection
8. Programming/Test button
4
1
7
8
3
5
6
2
Figure 1. MAXinBOX66

Technical Documentation
© Zennio Avance y Tecnología S.L. Edition 3 Further information www.zennio.com Page. 2/ 2
Any combination of the next accessories is allowed in the inputs:
SAFETY INSTRUCTIONS
Do not connect Main Voltage (230 V) or any other external voltages to any point of the BUS.
Connecting an external voltage might put the entire KNX system at risk.
Flexible cable with crimping terminals or rigid cable without terminals must be used for output connection.
Make sure during the installation that there is always sufficient insulation between the mains voltage 230V and the bus or
the extension inputs.
Once the device is installed, the output terminal should not be accessible.
OUTPUTS SPECIFICATIONS AND CONNECTIONS
Contact type
Potential free outputs through bistable
relays with tungsten pre-contact.
Disconnection type
Micro-disconnection
Rated current by output
16A * 250V AC (4000 VA)
16A * 30V DC (480W)
Maximum inrush current
800A/200μs (fluorescent lamps)
165A/20ms (resistive lamps)
Dropping voltage
Negligible
Outputs per common (channel)
1 individual output
Different phases connection
Possibility to connect different phases in
adjoining outputs
Maximum current
60A
Connection type
Terminal block (screw)
Recommended cable section
0.25 mm² to 4 mm² (26-10 AWG)
Cable type
Stranded or solid wire
Maximum response time
50 ms
Contact type
Potential free outputs through bistable
relays with tungsten pre-contact.
No. of automatic cycles (A)
per automatic action
Mechanical
(min)
3 million operations (60cpm)
Electrical
(min.)
100.000 cycles at Max. current (6cpm
and resistive load)
INPUT SPECIFICATIONS AND CONNECTIONS
CONCEPT
DESCRIPTION
Number of inputs per common
6
Input voltage
+3.3V DC for the common
Input current
1.0mA @ 3.3V DC (each input)
Input impedance
Aprox. 3.3kΩ
Switching type
Dry voltage contacts between
input and common
Connection method
Cable screw terminal
Max. cable length
30 m.
NTC probe length
1.5 m.
NTC accuracy (@ 25ºC)
0.5ºC
Temperature measure precision
0.1ºC
Cable cross-section
0.15 mm² to 2.5 mm² (26-12 AWG)
Response time
Max 10ms.
Attaching MAXinBOX66 to DIN rail:
Removing MAXinBOX66 from DIN rail:
Figure 2: (From up to down and
from left to right) Terminal block 1
wiring examples for shutter channel,
outputs with same phase or outputs
with different phases.
Temperature
probe
references:
ZN1AC-NTC68E
ZN1AC-NTC68F
ZN1AC-NTC68S
Up to two motion sensors
can be plugged into the
same MAXinBOX66 input
(parallel wiring)
Motion sensor cable screw
terminal.
Motion sensor references:
ZN1IO-DETEC-P(1)
ZN1IO-DETEC-X
Temperature Probe
Motion Sensor
Switch/Sensor/
Push button
WIRING AND ASSEMBLY DIAGRAMS
(*)In order to guarantee the correct functioning of relays when several outputs are controlled jointly, it is necessary to place the
actuator as close as possible to the KNX power supply. A 29VDC KNX power supply is recommended.
(1) The micro switch number 2 in the ZN1IO-DETEC-P must be in Type B position to work properly.
Motion sensor reference:
ZN1IO-DETEC
ZN1IO-DETEC-N
ZN1IO-DETECT-P(1)