Ancheer AM004142 Specification sheet

E-Bike
PRODUCT INSTRUCTION
MANUAL
Caution : Please read the manual before your first ride!

Safety Instruction
General Information
Bike Use
Installation And Adjustment
Meter Operation
Battery And Charging
Maintenance
Warranty
Attachment
Warnings
01
03
06
08
13
14
16
17
18
CONTENTS
20

ANCHEER
1
Thank you for choosing our products.
To ensure your safety and health, we encourage you to read this manual thoroughly before
you assemble the bike and take the first ride.Safe and effective use can only be assured if
the equipment is assembled, maintained, and used properly. More importantly, this will
offer you a general understanding and get the most out of your bike.Please check your
electric bike before every ride, especially when traveling long distances.
This manual is intended as a general guide to your new e-bike. For technical support,
including repair information, please consult your dealer.
Was Sie vor der Anwendung wissen sollten
Do not use the product before carefully reading the instructions from this manual and
understanding the performance of the item;
Don't lend this product to people who can't operate it, so as not to cause harm; if you
lend the bike, please let the user follow instructions, it could help to decrease the risk of
accident;
The E-bike cannot be used as off-road vehicles or used for extreme bicycle sports; when
riding the bicycle, please wear a safety helmet and protective gear. It is forbidden to ride
with one hand;
Please abide by the traffic rules and prohibit riding on motorized lanes and roads with
multiple pedestrians;
Carry people or objects in accordance with the requirements of laws and regulations, and
do not park in the building's lobby, evacuation stairs, walkways, and safe entrances and
exits;
It is recommended to charge and park in an outdoor dedicated parking hall, while
avoiding rain; when charging, keep away from combustibles, and the charging time
should not be too long;
For safety reasons, please do not change the default speed setting of the electric bicycle
and do not exceed speed limit in accordance with the traffic rule. Riding on non-
motorized lanes, downhills and paved roads not exceeding 15km/h;
When adjusting the handlebar or saddle, please be careful not to exceed the safety line
markings on the handlebar and saddle;
Please check the tire pressure before riding, the recommended tire pressure is 35- 45PSI;
Please check the power circuit, lighting circuit, etc. before riding;
●
●
●
●
●
●
●
●
●
●
Safety Instruction

ANCHEER
2
Safety Instruction
Before riding, please check whether the front and rear brakes work normally, check
the fastening status of the handlebars and front and rear wheels, and check whether
the reflector is damaged or contaminated;
When using the motor, please be careful not to hit vigorously and keep the rotating
shaft lubricated;
Try to avoid traveling in severe weather such as heavy rain;
Riding in rain or snow, the braking distance will be extended, pay attention to slow
down;
It is not allowed to exceed the maximum load of the vehicle body when riding (the
maximum load is 120KG);
It is suitable for people of 16+ years old and physically fit adults, and it is strictly
forbidden to drive electric bicycles on the road by people under 16 years old.
●
●
●
●
●
●

ANCHEER
3
General Information
1. About ANCHEER Electric Bike
ANCHEER electric bike is a leading icon of e-bikes. For years, ANCHEER has been not only
dedicating to innovation, cutting-edge technology and premium materials, but also
providing cost effective e-bikes, to satisfy riders' various needs of transportation and even
desire of exploring sports & outdoors life. Just ride freely with ANCHEER !
2. What’s In the Box (Parts List)
Description Quantity
ANCHEER Electric Bike
Pedal 2
1
User Manual
Saddle 1
1
Key
Saddle Tube
Front & Rear Fender
Stem
1
1
1
2
Power Adapter
Kickstand
Quick Release Skewer
Reflector
1
1
1
1
Battery
Tools Bag 1
1

ANCHEER
4
General Information
3. Bike Component
Handlebar Controller Height
Adjustment
Cushion
Battery bag
Lamp
Tire
Damping fork
Height
Adjustment
Variable speed
flywheel
Anti-out
chain wheel
Pedal
4. Tool List

ANCHEER
5
General Information
CORRECT FRAME SIZE
For safe and comfortabel riding there should be clearance of 78cm/31in from ground to the
crotch of the intended rider. Also, at least 3-8cm/1-3in between the crotch and the top tube
of the bicycle with both feet flat on the ground. Women can use a men's style bicycle to
determine the correct size for women's model.

ANCHEER
6
Bike Usage
Before Riding
During riding
Before riding the bike on the open road, try all the settings on the electric bike, and get
used to various results in a safe and controllable environment.
Please check the power circuit, lighting circuit, and test the brake system before
cycling.
Always check the tire pressure before starting to ride, and make sure that the tire is
inflated to a pressure within the specified range.
In order to ensure the safety of riding, please check regularly for loose parts or screws.
The places that need to be checked include but not limited to the seat tube, wheels,
handlebars and pedals.
If necessary, please confirm whether the battery capacity can meet you riding demand.
2.
1.
If the pressure exceeds the recommended maximum value, the tire may blow
out of the rim, which may damage the bicycle and cause injury to the cyclist and
nearby people.
If the pressure is too low, the wheel may be damaged, or the inner tube may be
squeezed, causing the tire to leak air.
Please wear helmets and riding gear that meet the requirements in accordance with
regulations.
Avoid traveling in severe weather such as heavy rain.
Carry people or objects in accordance with the requirements of laws and regulations,
and the load of the entire bike should not exceed 120kg.
Obey the traffic rules.
●
●
●
●
●
●
●
●
●
After riding
After heavy use, do not touch the hot surface, such as the disc brake rotor or the side
edge of the brake rim.
When folding the kickstand, always make sure that the stand is secure and the base is
firm to prevent the bicycle from falling.
If the bicycle is splashed with moisture, please wipe it dry and clean in time.
●
●
●

ANCHEER
7
Bike Usage
Shifting Recommendations
Brake Adjustment
In order to increase the range, we recommend shifting according to the speed.
For starting and low-speed riding, it is best to use a low-speed gear.
At higher speeds, a higher gear should be selected.
Loosen or tighten the barrel adjuster at the end of the brake cable lever. This will make
a small adjustment to the gap of the brake pads. If this is not enough to create the
correct gap, then:
Loosen the two positioning bolts, but do not remove them. Slowly rotate the wheel and
check the space between the rotor and the brake pad; adjust the position of the brake
pad so that the rotor does not rub and is slightly close to the outer pad (the gap between
the rotor and the pad should be just enough to prevent friction). Make sure that the rotor
and the pads are parallel to each other. After the adjustment is complete, tighten the
bolts.
If the rotor always rubs against the brake pads or the gap is too large, you can adjust
the brake pad gap by loosening the cable clamp bolts and slightly releasing the cable
to increase the gap or tightening the cable to reduce the gap, and then tighten the
bolts again.
Ensure that the brake cables are properly inserted into the brake levers before aligning a
mechanical disc brake. If the disc rotor is bent or damaged, replace the rotor first.
●
●
●
2.
1.

ANCHEER
8
Installation And Adjustment
Open the package of the bike, take out the electric bike and all the parts inside and use the
tool to cut off the packing rope.
1. Install the Stem and Handlebar
2. Montage der Basis
1.1
2.1
1.2
Insert the stem and tighten the screw.
Install the reflector and fender on the saddle tube.
Using the wrench from tool kit to loosen the four screws and put the stem into
the bike in balance and you can adjust the handlebar in a property angel and
position.

ANCHEER
9
Installation And Adjustment
3. Install Headlight and Front Fender
2.2
3.2
3.1
Set right position and adjust height to fit your riding habit, then tighten seat by
clamp. Please do not exceed the maximum saddle height.
Loosen Loosen the screw on the corresponding position of the front wheel, as
shown in the pics below. Put the headlight and fender in this position.
Please turn the whole bike upside down, and remember to put some packing
materials on the ground to avoid damaging the handlebar and meter.

ANCHEER
10
Installation And Adjustment
4. Install the Front Wheel
4.2
4.1
Put in the front wheel and use the quick release to fix the front wheel. Make
sure fork hanger hold onto wheel axle, and make sure the disc put into
middle of brake.
Using the tool to loosen the fixing rod of the front fork and remove it (this accessory
is to prevent the front fork from being deformed during delivery.

ANCHEER
11
Installation And Adjustment
5. Install the Pedals
6. Install the Kickstand
The pedal marked “R” has right-hand threads, tighten it in a clockwise direction. The
pedal marked “L” has left-hand threads, tighten it in a counterclockwise direction
(anti-clockwise).
Unscrew the screw in the kickstand, Install it and tighten the screw with tool.
5.1
6.1
Make sure the threads of each pedal are fully into the crank arm.
Make sure pedals are fully tightened with wrench.
Note: Be sure to identify R/L letters on pedal’s bolt when installing.
☛
☛
☛

ANCHEER
12
Installation And Adjustment
7. Install the Battery Bag
Fasten the battery bag belts.
Unzip the battery bag and find the connector.
Connect battery and zip the bag.
7.1
7.2
7.3
So far, congratulations! You have completed the assembly of the entire bike.
8. Adjust angle of brake lever, meter, gear shifter, throttle and louder
controller on handlebar, then tightens them with tools.

ANCHEER
13
Meter Operation
1. Meter Instruction
2. Meter Operation
MODE
POWER
M
+ -
Assistance Level:Low
Assistance Level:Mid
Assistance Level:High
Battery Indicator
DOWN UPON/OFF
Operating instructions
To switch on/
off the E-Bike
system, hold
the “M” key for
2s. The default
value is “low”
pedal assist
level.
Press “+” to
crease into
pedal assist level
“mid”.
Press “+” again
to move into
pedal assist
level “high”.
“high” is the
maximum
power of PAS.
Full Electric
Function (Pure
electric mode):
Press“-”, until
all the three
“low”,“mid”,
“high” indicators
are off.
MODE
POWE R
high
M
+ -
MODE
POWER
M
+ -
MODE
POWER
M
+ -
MODE
POWER
M
+ -
midlow highmidlow highmidlow highmidlow
3. Operation Cautions
Avoid the risk of collision.
Don’t modify system parameters to avoid parameters disorder.
Contact the seller when error code appears.
●
●
●

ANCHEER
14
Battery And Charging: Further Information
Please follow the instructions for use, otherwise the consequences are at his own risk.
Please use the original special charger. It is strictly prohibited to use other chargers.
Pay attention to the battery type and applicable voltage that the charger can charge, and
it is strictly forbidden to mix them. The charging time shall not exceed 12 hours, and the
charging current shall not exceed 2A.
When charging, it should be placed in a ventilated environment, and it is strictly
forbidden to charge in a confined space, residential building or in a hot environment.
When charging, insert the battery first, then add the mains. After charging fully (the
green light will be on), first cut off the mains, and then unplug the battery. It is forbidden
to connect the charger to the AC power supply without load for a long time. During
the charging process, if the indicator light is abnormal, a peculiar smell appears, or the
charger casing is overheated, stop charging immediately, and repair the charger or
replace the charger.In the process of use and storage, pay attention to avoid the entry of
foreign objects, especially avoid the inflow of water or other liquids, so as to avoid short
circuit inside the charger.
If you need to bring the charger outside, be careful to protect your charger from being
collision or crushing during cycling. Do not remove or replace the components in the
charger yourself.
When not in use for a long time, keep the battery in a cool and dry place, and charge the
battery for two hours a month.
●
●
●
●
●
●
Battery: Further information
Charging: Safe operation guide
Keep the battery out of reach of children.
Charging at 0°C~40°C/ 32°F~104°F, and discharging at -5°C~40°C/ 23°F~104°F. Please
do not store the battery in temperatures above 35°C/ 95°F or below -5°C/ 23°F.
Keep the battery dry, do not put the battery in acidic or alkaline liquid, keep away from
rain, fire and high temperature environment.
It is strictly forbidden to connect the positive and negative poles of the battery
reversely, and it is strictly forbidden to damage, disassemble or short-circuit the battery.
Used batteries are hazardous chemicals, and the used batteries should not be
disassembled without authorization, and recycled by relevant professional
departments.
Use the original battery. Do not replace it with other brand’s or product’s battery.
●
●
●
●
●
●

ANCHEER
15
Reminder
Battery and charging: Further Information
Battery must be recycled or disposed of in an environmentally sound manner.
Do not dispose of the battery in a fire. The battery may explode or leak.
Do not dispose of a battery in your regular household trash.
●
●
●
Battery Disposal
Charge a new battery 4-6 hours before you use it in your product for the first time.
If the battery is dropped or damaged due to a bicycle accident, there may be a danger
of electrolyte leakage. Please stop using it immediately.
It is better not to wait until the power is completely exhausted before charging, which
can more effectively extend the battery life. Besides, Overheating or undercharging the
battery may shorten battery life.
How far can a fully charged battery go? It depends on the load weight, road conditions
and battery capacity. But under the same conditions, the average speed can last longer
riding distances. Using pedal assist mode allows you to go further.

ANCHEER
16
Maintenance
The front and rear wheels of the vehicle should be located in the center of the
front fork or frame.
After riding, please store the bike in a place without sunlight and rain.
Water showering is forbidden, and the surface of the bike body can be wiped with
a semi-dry cloth.
Do not touch the charging hole on the bicycle, or touch it with metal or liquid,
otherwise, it may cause an accident due to an instantaneous short circuit of the
current.
Check all cables and cable housings for fraying, breaks, rust, or corrosion and
replace if necessary.
Check the motor and brake frequently, and do not fill the brake area with oil.
Additionally, check the brake pads for any damage as they will be worn over time
and eventually need replacement.
Regularly check the various screws of the bike and the places that need to be
fastened, and regularly reinforce to prevent injury and unnecessary wear and tear
on your e-bike.
Recommended torque (unit: kgf.cm): the horizontal screw 60-80, the stem screw
175- 200, the seat cushion screw 175-250, the wheel screw 320-450.
Regularly check the tension of the chain, which can be adjusted by the chain
regulator.
Always check the tire for scratches, cracks, or excessive wear. The inner tube and
the valve should be perpendicular to the wheel hub and not crooked. Accidentally
punctured, damaged or excessively worn inner and outer tires need to be
replaced immediately, please seek professional technicians to repair or replace
your tires.
It is forbidden to modify key structural parts such as the frame, front fork, standpipe,
and electrical function parts. If damaged, use the original parts to replace it.
Otherwise, the guarantee service will not be provided.Any loss or damage caused
by the modification shall be solely responsible.
●
●
●
●
●
●
●
●
●
●
●

ANCHEER
17
Warranty
One-Year Limited Hardware Warranty
Your electric bike includes a One Year Limited Hardware Warranty. ANCHEER provides
warranty service for the electric bikes. If there is a hardware defect and a valid claim is
received during the warranty period, we will resend new parts within the scope permitted
by law.
The Warranty covers product defects in materials and workmanship under normal use.
This Warranty is limited to original purchasers and is not assignable or transferable.
The Warranty starts on the date of your purchase and lasts for one year (the "Warranty
Period") and the Warranty Period is not extended if the product is repaired or replaced.
The Warranty does not cover any damage due to: improper use; failure to follow the product
instructions or to perform any preventive maintenance; unauthorized repair; external causes
such as accidents, abuse, or other actions or events beyond our reasonable control.
Customer Services
We provide lifetime customer support services. For any questions about the product,
please contact customer service from where you brought the equipment. We will be
happy to answer your questions.
Any question about the item, please contact the
Customer Service:
ANCHEER support team:[email protected].
☛
Accessories WarrantyPeriod Service Content Quality Problem
A year
A year
A year
A year
A year
Motor
Controller
Charger
Lithium
Battery
Accelerator
Free delivery of parts
Free delivery of parts
Free delivery of parts
Free delivery of parts
Free delivery of parts
Motor will not be able to
use
Natural conditions (such
as impact force cannot be
used except damage)
Failure occurs under normal
use
Failure occurs under normal
use
Can't charge discharge
under normal use

ANCHEER
18
Attachment
Technical parameters
Performance index Project Parameter
Wheel Size
Vehicle Size
26 Inches
Body Material Aluminium Alloy
Maximum Load 264 lbs (120KG)
Vehicle Weight 51 lbs (23KG)
Maximum Speed 15 mph (25km/h)
Maximum Gradient 10 Degrees
Front Derailleur 3-Speed
Rear Derailleur 7-Speed
Mileage Range 15 miles (pure electric)
Rated Voltage
Working Temperature 23°F-95°F (-5℃~35℃)
36V
Battery Capacity 8Ah
Service Life 500 Times
Motor Power
Display
250W
LED Display
Motor Type
Brake
Brush-less Gear Motor
Disc Brake
Maximum Torque
Suspension
Light
34N.M
Double shock absorption
Front Light
Input Voltage 100-240V
Input Current 1.8A
Output Voltage 42V
Output Current 2A
1760*650*1080mm
Basic Parameters
Performance
Parameters
Battery Parameters
Motor Parameters
Other Parameters
Charger Parameters