Andamiro SpongeBob Squarepants VR Bubble Coaster User manual

2
FIRST STEPS 4
Step 1 – Unpacking your Coaster 4
Step 2 – Removing the support pipes 5
Step 3 – Removing the BLACK-DISPLAY 6
Step 4 - Installing the support pipes 7
Step 5 – Installing the back-display on the simulator base 8
Step 5.1 – Adjusting the Pipes Position 9
Step 6 – Opening the back-display door and seat 10
Step 7 – Inserting the cable through the internal back-display pipe 11
Step 8 – Tools required to attach the wind system cable to the LED cables 12
Step 9 – Tying up the LED cables to the sound system cable 13
Step 10 – Cutting the zip tie 14
Step 11 – Connecting the LED cables to the power 15
Step 12 – Inserting the cable through the internal back-display pipe 16
Step 13 – Pulling the wind system cable to the base connector 17
Step 14 – Connecting the wind system cable 18
Step 15 – Connecting the payment system cable 19
Step 16 – Inserting the power cable through the internal back-display pipe 20
Step 17 – Connecting the power cable to the power outlet 21
Step 18 – Connecting the sound cable to the base 22
Step 19 – Closing the seat 23

3
Step 20 – Closing the latches 24
Step 21 – Locking the latches 25
VR HEADSET INSTALLATION 26
Step 1 – Installing the headsets 26
Step 2 – Inserting the headset cable through the Back-display 27
Step 3 – Grabbing the headset cable from inside the Back-display 28
Step 4 – Attaching the headset to the Back-display 29
Step 5 – Connecting the USB cable to the computer 30
Step 6 – Turning the Headset on 31
Step 7 – Turning the simulator ON (internal button) 32
Step 8 – Closing the back-display door 33
CONNECTING THE RILIX COASTER TO THE INTERNET 34
Step 1 34
Step 2 35
Step 3 36
Step 4 37
Step 5 38
Step 6 39
ADJUSTING THE VOLUME 40
CONTACT INFO 41

4
FIRST STEPS
STEP 1 – UNPACKING YOUR COASTER
Remove the straps and unwrap the Rilix Coaster. Be careful when using sharp tools so as
not to damage the surface of the product.

5
STEP 2 – REMOVING THE SUPPORT PIPES
The Back-display of the simulator is shipped disassembled, between the seat and the
simulator hood. To remove the Back-display without damaging it, remove the support
pipes (pictures 1 and 2) that are fitted to the rear of the simulator before removing the
Back-display.

6
STEP 3 – REMOVING THE BLACK-DISPLAY
FIGURE 1 - Two people are required to remove the Back-display.
FIGURE 2 - Holding on both sides, lift the Back-display and place it on the simulator's seat.
FIGURE 3 - Lift the Back-display and place it on a flat surface.

7
STEP 4 - INSTALLING THE SUPPORT PIPES
FIGURE 1 - With the Back-display positioned on a flat surface (such as a table, for
example), insert the support pipes into the two holes at the bottom of the Back-display.
Then, push each pipe firmly until it reaches the internal limiter.
FIGURE 2 - Make sure the opening at the bottom of each pipe is facing forward.

8
STEP 5 – INSTALLING THE BACK DISPLAY ON THE SIMULATOR
BASE
FIGURE 1 - After installing the support pipes, two people are needed to lift the back
display to a vertical position.
FIGURE 2 - In a vertical position, place the back display in front of the rear of the simulator
FIGURE 3 - The back of the simulator has two holes where the pipes need to be placed. Lift
the back display and fit the two support pipes into these holes.
FIGURE 4 - Align the two support pipes and make sure they reach the bottom of the base.

9
STEP 5.1 – ADJUSTING THE PIPES POSITION
After installing the support pipes, turn the pipe until the pipe’s opening is facing forward,
increasing the hole where all the wires will pass through.

10
STEP 6 – OPENING THE BACK DISPLAY DOOR AND SEAT
FIGURE 1 – The back display has two rear access doors for electronic components. Use the
key that comes with the product and open the top door.
FIGURE 2 and 3 – The simulator seat has four locking tabs. Open the four clips. Two are
located on the back of the seat, and two on the sides.
FIGURE 4 – Move the seat from the back to the front by moving the back first, as shown in
the picture.

11
STEP 7 – INSERTING THE CABLE THROUGH THE INTERNAL
BACK DISPLAY PIPE
FIGURE 1 – The inner part of the back display has two holes. And four cables will make the
communication between the back display and the base of the simulator.
FIGURE 2 - Insert the wind cable through the pipe hole on the left side, inside the back
display.
FIGURE 3 – The cable must pass through the entire length of the pipe and reach the base
of the simulator.
FIGURE 4 – When the cable touches the simulator's base, pull until a good cable length
comes out of the pipe.

12
STEP 8 – TOOLS REQUIRED TO ATTACH THE WIND SYSTEM
CABLE TO THE LED CABLES
The LED cables are located under the seat. They need to be pulled up through the back
display pipe to reach the connectors situated with the central computer parts. Therefore,
it would help if you used the sound system cable to “hook” those LED cables through the
pipe. To tie the sound system cable to the LED cables, a small zip tie, and a cutter plyer will
be required for the task, as shown in FIGURE 1.

13
STEP 9 – TYING UP THE LED CABLES TO THE SOUND SYSTEM
CABLE
FIGURE 1 – With the zip tie, tie both wires together.
FIGURE 2 - Ensure both cables are securely tied down before pulling the wind system
cable.
FIGURE 3 - On the back of the back display, pull the wind cable through the pipe so that
the LED cables come together.
FIGURE 4 - Ensure the LED cables run entirely through the pipe.

14
STEP 10 – CUTTING THE ZIP TIE
To connect the LED cables to the power, cut the zip tie to release both wires.

15
STEP 11 – CONNECTING THE LED CABLES TO THE POWER
FIGURE 1 – The connectors for the LED cables are located on the right side of the back
display, usually inside a black cable organizer. Connect both LED cables and screw the
lockers to secure the connection.
FIGURE 2 – The picture shows the way both LED cables are secure and ready.

16
STEP 12 – INSERTING THE CABLE THROUGH THE INTERNAL
BACK DISPLAY PIPE
FIGURE 1 - Now that the LED cables are connected and ready, it's time to re-insert the
sound system cable into the pipe inside the back display.
FIGURE 2 - Push the wind system cable through the left inner pipe until the cable reaches
the base. If the cable is not going down, turn it clockwise to facilitate the passage.

17
STEP 13 – PULLING THE WIND SYSTEM CABLE TO THE BASE
CONNECTOR
Once the cable comes out of the pipe at the bottom, pull until all the cable length is
available.

18
STEP 14 – CONNECTING THE WIND SYSTEM CABLE
There are four connectors available, each with a specific number of pins. Each cable will
connect to only one connector; the wind system cable has a two-pin connector. Check the
pin number of each connector before connecting each cable. Once you have identified the
correct connector, connect the cable, and screw the lock by turning it clockwise.

19
STEP 15 – CONNECTING THE PAYMENT SYSTEM CABLE
Repeat steps 12, 13, and 14 with the payment system cable. The payment system cable
(for both swipers) has a connector with five pins.

20
STEP 16 – INSERTING THE POWER CABLE THROUGH THE
INTERNAL BACK DISPLAY PIPE
Insert the power cable through the pipe hole located on the left side, inside the back
display.