Antunes VCT-35 User manual

P/N 1011287 Rev. E 02/18
Vertical Contact Toaster
owner’s manual
Model VCT-35
Manufacturing Numbers:
9200641, 9200642, & 9200643
www.antunes.com

VERTICAL CONTACT TOASTER
2P/N 1011287 Rev. E 02/18
General
The Vertical Contact Toaster, is designed for contact
toasting of buns. The toaster design allows the opera-
tor to place buns on both sides of the heated platen
at the same time. Buns are placed into the top of the
toaster and uniform, golden brown, warm buns are then
retrieved at the bottom of the toaster.
This manual provides the safety, installation and oper-
ating procedures for the Vertical Contact Toaster. We
recommend that all information contained in this manu-
al be read prior to installing and operating the unit.
Your Vertical Contact Toaster is manufactured from the
finest materials available and is assembled to our strict
quality standards. This unit has been tested at the fac-
tory to ensure dependable trouble-free operation.
Warranty Information
Please read the full text of the Limited Warranty in this
manual.
OWNER INFORMATION
TABLE OF CONTENTS
IMPORTANT! Keep these instructions for future reference. If the unit changes
ownership, be sure this manual accompanies the equipment.
If the unit arrives damaged, contact the carrier imme-
diately and file a damage claim with them. Save all
packing materials when filing a claim. Freight damage
claims are the responsibility of the purchaser and are
not covered under warranty.
The warranty does not extend to:
• Damages caused in shipment or damage as
result of improper use.
• Installation of electrical service.
• Normal maintenance as outlined in this manual.
• Malfunction resulting from improper maintenance.
• Damage caused by abuse or careless handling.
• Damage from moisture into electrical
components
• Damage from tampering with, removal of, or
changing any preset control or safety device.
Owner Information .....................................................2
General......................................................................2
Warranty Information .................................................2
Service/Technical Assistance ....................................3
Important Safety Information ....................................3
Specifications .............................................................5
Electrical Ratings & Plug Configurations...................5
Dimensions................................................................5
Installation...................................................................6
Unpacking..................................................................6
Assembling the Unit ..................................................6
Equipment Setup.......................................................7
Operation.....................................................................8
Operating Instructions ...............................................8
Safety Features .........................................................8
Maintenance................................................................9
Daily...........................................................................9
Conveyor Belt Chains..............................................10
Replacing Roller Tensioners....................................11
Replacing Conveyor Motor and Fan Blade .............11
Troubleshooting .......................................................12
Wiring Diagram.........................................................16
NOTES .......................................................................22
Limited Warranty ......................................................24

VERTICAL CONTACT TOASTER
3
P/N 1011287 Rev. E 02/18
Use only genuine Antunes replacement parts in this
unit. Use of replacement parts other than those sup-
plied by the manufacturer will void the warranty.
Service/Technical Assistance
If you experience any problems with the installation
or operation of your unit, contact Antunes Technical
Service at [phone] (toll free).
Fill in the information below and have it handy when
calling for assistance. The serial number is on the
specification plate located on the rear of the unit.
Purchased From:
Date of Purchase:
Model No.:
Serial No.:
Mfg. No.:
OWNER INFORMATION (continued)
Antunes reserves the right to change specifications and product design without notice. Such revisions do not
entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased
equipment.
Throughout this manual, you will find the following safety words and symbols that signify important safety issues with
regards to operating or maintaining the equipment.
WARNING
GENERAL WARNING. Indicates informa-
tion important to the proper operation of
the equipment. Failure to observe may
result in damage to the equipment and/or
severe bodily injury or death.
WARNING
ELECTRICAL WARNING. Indicates infor-
mation relating to possible shock hazard.
Failure to observe may result in damage
to the equipment and/or severe bodily
injury or death.
CAUTION
GENERAL CAUTION. Indicates informa-
tion important to the proper operation of
the equipment. Failure to observe may
result in damage to the equipment.
WARNING
HOT SURFACE WARNING. Indicates
information important to the handling of
equipment and parts. Failure to observe
caution could result in personal injury.
IMPORTANT SAFETY INFORMATION

VERTICAL CONTACT TOASTER
4P/N 1011287 Rev. E 02/18
In addition to the warnings and cautions in this manual,
use the following guidelines for safe operation of the
unit.
• Read all instructions before using equipment.
• For your safety, the equipment is furnished with
a properly grounded cord connector. Do not
attempt to defeat the grounded connector.
• Install or locate the equipment only for its intend-
ed use as described in this manual. Do not use
corrosive chemicals in this equipment.
• Do not operate this equipment if it has a dam-
aged cord or plug, if it is not working properly, or
if it has been damaged or dropped.
• This equipment should be serviced by quali-
fied personnel only. Contact Antunes Technical
Service for adjustment or repair.
• Do not block or cover any openings on the unit.
• Do not immerse cord or plug in water.
• Keep cord away from heated surfaces.
• Do not allow cord to hang over edge of table or
counter.
The following warnings and cautions appear throughout
this manual and should be carefully observed.
• Turn the unit off, disconnect the power source
and allow unit to cool down before performing
any service or maintenance on the unit.
• The toaster should be grounded according to
local electrical codes to prevent the possibility of
electrical shock. It requires a grounded recep-
tacle with separate electrical lines, protected by
fuses or circuit breaker of the proper rating.
• Bread may burn. Therefore toasters must not be
used near or below curtains or other combustible
walls and materials. Failure to maintain safe
operating distances may cause discoloration or
combustion.
• Failure to use release sheets may result in dam-
age to the equipment and loss of warranty cover-
age.
• All electrical connections must be in accordance
with local electrical codes and any other appli-
cable codes.
• WARNING ELECTRICAL SHOCK HAZARD.
FAILURE TO FOLLOW THESE INSTRUCTIONS
COULD RESULT IN SERIOUS INJURY OR
DEATH.
- Electrical ground is required on this appliance.
- Do not modify the power supply cord plug. If
it does not fit the outlet, have a proper outlet
installed by a qualified electrician.
- Do not use an extension cord with this appli-
ance.
- Check with a qualified electrician if you are in
doubt as to whether the appliance is properly
grounded.
IMPORTANT SAFETY INFORMATION (continued)

VERTICAL CONTACT TOASTER
5
P/N 1011287 Rev. E 02/18
SPECIFICATIONS
Model &
Mfg. Number Volts Watts Amps Hertz Plug Description Conguration
VCT-35
9200641 120 1760 14.6 50/60
NEMA 5-15
15 Amp.,
250 VAC
Non-Locking
(assembly only)
VCT-35
9200642 208-240~ 3460 16.6 - 14.4 50/60
CEE 7/7
16 Amp., 250 VAC
(assembly only)
VCT-35
9200643
(Damper Units)
208-240~ 3460 16.6 -
14.4 50/60
CEE 7/7
16 Amp., 250 VAC
(assembly only)
Electrical Ratings & Plug Configurations
10-3/4
9-3/4"
20-5/16"
22 11/16
23-1/4"
(590.5 mm)
3/4”
(19.1 mm)
555.8 mm)
(519.9 mm)
(247.6 mm)
(273.1 mm)
14-5/8"
(371.5 mm)
Dimensions

VERTICAL CONTACT TOASTER
6P/N 1011287 Rev. E 02/18
Figure 2. Installing Bun Chute
Bun Chute
Yellow Support Rod
Hook Bun Chute over rear
bottom conveyor cover
yellow support rod
Figure 1. Installing Damper Assy.
Heat Shield
Heat Shield
Conveyor
Cover Assy.
Yellow Support
Rod
Conveyor
Cover Assy.
Conveyor
Cover Assy.
Conveyor
Cover Assy.
Unpacking
1. Remove unit and all packing materials from ship-
ping carton.
2. Open the large box. It should contain:
• Bun chute (Figure 2).
• Plastic bag containing the release sheet
(Figure 4)
3. Remove all packing materials and protective cov-
erings from the unit and parts.
NOTE: If any parts are missing or damaged, con-
tact Antunes Customer Service IMMEDIATELY at
[phone] (toll free).
Assembling the Unit
1. Remove the Heat Shield and the front and rear
Conveyor Covers (Figure 1).
2. Install the Damper Assembly. (Figure 1).
NOTE: Make sure the damper assy. rests only on
the bottom front and rear yellow support rods.
3. Install the Bun Chute (Figure 2).
4. Remove the Release Sheet from the plastic bag
and lay it on a clean, flat surface. Fold the sheet
exactly in half (Figure 3).
5. Crease the sheet at the fold using only your fin-
ger (Figure 3).
NOTE: Do not use metal tools to crease the sheet.
6. Install the Release Sheet by draping it over both
sides of the Platen surface. The crease should be
centered directly on top of the Platen (Figure 4).
7. Re-install the front and rear Conveyor Covers
(Figure 4).
IMPORTANT: Make sure the Conveyor Covers rest
only on both the top and bottom yellow support
rods.
8. Install the Heat Shield so that the clips fit over the
top of the Platen and retains the Release Sheet
in place (Figure 4).
INSTALLATION
CAUTION
Failure to use release sheets may result in dam-
age to the unit and loss of warranty coverage.

VERTICAL CONTACT TOASTER
7
P/N 1011287 Rev. E 02/18
NOTE: As of March 2017, the Interlock Switch was
removed from use. If your toaster has the Interlock
Switch, you will need to place the Heat Shield onto
the toaster in order for the conveyors to turn. If
your toaster does not have an Interlock Switch, the
conveyors will turn as long as the unit is on.
NOTE: Check the release sheet to make sure it
is not caught in the conveyor. Additional release
sheets can be obtained by ordering part number
7000249 (3 pack) or 7000250 (10 pack).
Equipment Setup
When placing the toaster into service, pay attention to
the following guidelines.
• Make sure power to the unit is off and the toaster
is at room temperature.
• Do not block or cover any openings on the unit.
• Do not immerse cord or plug in water.
• Keep cord away from heated surfaces.
• Do not allow cord to hang over edge of table or
counter.
Connect the unit to the power supply. Refer to the
specification plate for the proper voltage.
Figure 3. Folding Release Sheet
Lay sheet on a flat surface
Fold over so ends meet
Press lightly with finger to
form crease
Figure 4. Installing Release Sheet
Platen
Conveyor Cover
Conveyor Cover
Heat Shield
Release Sheet
Conveyor Interlock
Switch (Some
Models)
WARNING
ELECTRICAL SHOCK HAZARD. FAILURE TO
FOLLOW THE INSTRUCTIONS IN THIS MANUAL
COULD RESULT IN SERIOUS INJURY OR DEATH.
• Electrical ground is required on this appliance.
• Do not modify the power supply cord plug. If
it does not fit the outlet, have a proper outlet
installed by a qualified electrician.
• Do not use an extension cord with this appliance.
• The toaster should be grounded according to local
electrical codes to prevent the possibility of electri-
cal shock. It requires a grounded receptacle with
separate electrical lines, protected by fuses or cir-
cuit breaker of the proper rating.
• Check with a qualified electrician if you are in
doubt as to whether the appliance is properly
grounded.
CAUTION
Bread may burn. Therefore toasters must not be
used near or below curtains or other combus-
tible walls and materials. Failure to maintain safe
operating distances may cause discoloration or
combustion.
All electrical connections must be in accordance
with local electrical codes and any other appli-
cable codes.
INSTALLATION (continued)

VERTICAL CONTACT TOASTER
8P/N 1011287 Rev. E 02/18
Operating Instructions
1. Set the Bun Thickness Adjustment Control knobs
to the desired settings (Figure 6). The recom-
mended setting is 6.
NOTE: After initial run of 4-6 buns, adjust controls
according to the desired finished product.
2. Turn the Rocker Switch (power On/Off) to ON
(Figure 5).
3. Turn the Temperature Control to 10. Allow 30
minutes warm-up time before proceeding.
4. Drop buns into toaster with the cut sides of heel
and crown facing each other (Figure 5).
5. Toasted product will drop into the Bun Landing
Area (Figure 5).
6. Test at least 4 buns before putting toaster into
service. Turn the Temperature Control to a lower
setting for lighter toasting or to a higher setting for
darker toasting.
7 Turn the unit off when finished toasting
Safety Features
HI-LIMIT RESET BUTTON
A hi-limit thermostat will turn off electrical power to the
heater and control circuits if the unit overheats. To
reset this thermostat, allow sufficient time (10-15 min-
utes) for the unit to cool down, then press and release
reset button located at the rear of the unit (Figure 5).
If the unit requires continuous resetting, contact your
Maintenance Person or Antunes Technical Service.
CONVEYOR INTERLOCK SAFETY SWITCH
A Conveyor Interlock Safety Switch (some models) is
located on top of the unit under the Heat Shield (Figure
4). The conveyors will not rotate unless the Heat
Shield is properly in place and activating the Conveyor
Interlock Safety Switch.
NOTE: As of March 2017, the Interlock Switch was
removed from use. If your toaster has the Interlock
Switch, you will need to place the Heat Shield onto
the toaster in order for the conveyors to turn. If
your toaster does not have an Interlock Switch, the
conveyors will turn as long as the unit is on.
OPERATION
1
2
3
4
5
1 = 1/2"(12.7mm)
2 = 5/8"(15.9mm)
4 = 3/4"(19.1mm)
5 =13/16"(20.6mm)
6 = 7/8"(22.2mm)
THICKNESS THICKNESS
1
2
3
4
5
6
6
3 =11/16"(17.5mm)
Figure 6. Bun Thickness Adjustment Controls
1
2
3
4
5
1 = 1/2"(12.7mm)
2 = 5/8"(15.9mm)
4 = 3/4"(19.1mm)
5 =13/16"(20.6mm)
6 = 7/8"(22.2mm)
THICKNESS THICKNESS
1
2
3
4
5
6
6
3 =11/16"(17.5mm)
Figure 5. Toaster Controls
Bun Thickness
Adjustment Controls
Bun Landing
Area
Rocker Switch
Hi-Limit Reset
Temperature Control
(see Figure 6)

VERTICAL CONTACT TOASTER
9
P/N 1011287 Rev. E 02/18
WARNING
Turn the unit off, disconnect the power source
and allow the unit to cool down before performing
any service or maintenance on the unit.
NOTE: As of March 2017, the Interlock Switch was
removed from use. If your toaster has the Interlock
Switch, you will need to place the Heat Shield onto
the toaster in order for the conveyors to turn. If
your toaster does not have an Interlock Switch, the
conveyors will turn as long as the unit is on.
NOTE: Check the Release Sheet to make sure it is
not caught in the Conveyor Belt Chain. Additional
Release Sheets can be obtained by ordering part
number 7000249 (3 pack) or 7000250 (10 pack).
Daily
CLEANING THE ACCESSORIES
1. Turn the unit off, unplug the power cord, and
allow the unit to cool for 30 minutes.
2. Remove the Heat Shield and Bun Chute. Wash
these items in soapy water, rinse with clear water,
sanitize, and allow to air dry.
3. Wipe down the outside of the toaster with a
slightly damp cloth and allow to air dry.
CLEANING THE RELEASE SHEET
1. Make sure the unit is turned off, the power cord is
unplugged, and the unit is cool. Put on heat resis-
tant gloves. Remove the Release Sheet (Figure
7).
2. Lay the Release Sheet on a clean, flat, dry sur-
face. Apply an appropriate cleanser to a clean,
dry towel.
3. Wipe the towel firmly across the Release sheet
from top to bottom over its entire surface. Repeat
this procedure with a clean, dry towel dampened
with water.
4. Next, wipe the Release Sheet with a clean towel
dampened with sanitizer and allow to air dry.
Repeat Steps 3 through 4 on the reverse side of
the Release Sheet.
5. Remove the front and rear Conveyor Covers
(Figure 4). Wipe the exterior of Conveyor Belt
chains with a clean, sanitized towel.
6. Install front and rear Conveyor Covers (Figure
4) and turn the unit on. Count to 10, then turn
toaster off. Remove the front and rear Conveyor
Covers again and wipe newly exposed section of
the Conveyor Belt chains. Re-install the front and
rear Conveyor Covers.
7. Install the Release Sheet by draping it over both
sides of the Platen with the crease centered
directly on the Platen (Figure 7).
8. Install the Heat Shield (Figure 7). The Heat
Shield clips fit over the tip of the Platen and retain
the Release Sheet in place.
MAINTENANCE
CAUTION
To prevent damage to the unit, do not use abra-
sive cleaners on the release sheet.
Heat Shield
Platen
Release Sheet
Interlock Switch
(Some Models)
Figure 7. Removing/Installing the Release Sheet

VERTICAL CONTACT TOASTER
10 P/N 1011287 Rev. E 02/18
Conveyor Belt Chains
MEASURING THE CONVEYOR BELT CHAINS
1. Facing the toaster, locate the approximate center-
point of the Conveyor Chain.
2. Pull the Conveyor chain away from the edge of
the toaster. Stand a U.S. Dime, 11/16” (1.8 cm)
coin on end between the frame and the chain.
If the gap is significantly wider than the coin,
REMOVE links as described in the section titled
Adjusting The Conveyor Belt Chains. Then,
measure the gap again to make sure it is not too
tight.
Check the opposite side of the toaster using the
same measurements.
MAINTENANCE (continued)
Figure 9. Removing Conveyor Belt Chain
Rotation
Upper Yellow Support Rod
Large Link
P/N 0800121
Small Link
P/N 0800204
NOTE: If the belt is too short (tight) to be reas-
sembled, remove an additional 1/2” link and install
a 3/4” link. This will make the conveyor belt 1/4”
shorter and enable it to be reassembled.
IMPORTANT: This is not covered under warranty. It
is a user responsibility.
REMOVING THE CONVEYOR BELT CHAINS
1. Turn the unit off, unplug the power cord, and allow
the unit to cool down.
2. Remove the Heat Shield, front and rear Conveyor
Covers, and Release Sheet (Figure 4).
NOTE: When replacing the Conveyor Belt chain, be
sure to clean the Release Sheet as well.
3. Set the Bun Thickness Compression Control
knobs to 6.
4. Disconnect the Conveyor Belt chain by squeezing
any two links together and unhooking both ends
of one link (Figure 8). A needle-nose pliers may
be required. Remove the Conveyor Belt chain.
NOTE: With conveyor belt removed, the tensioner
assemblies (4, page 24) and slide rails (40, page 24)
can be replaced.
Figure 8. Measuring Conveyor Belt Chains
ADJUSTING THE CONVEYOR BELT CHAINS
After a period of time, the conveyor belt links will wear
and the conveyor belt will stretch. This will eventually
cause the conveyor to jam as it rotates on the sprock-
ets. This is easily remedied by removing one or more
conveyor links from each side of the belt.
There are four 1/2” pitch links on each conveyor belt.
The rest of the links are 3/4”.
1. Remove the Conveyor Belt Chain as described in
the section titled Removing the Conveyor Belt
Chains.
2. To shorten a stretched Conveyor Belt chain,
remove one 1/2” link from the belt.
3. Reassemble the Conveyor Belt Chain to the
sprockets as described in the section titled
Replacing the Conveyor Belt Chains.

VERTICAL CONTACT TOASTER
11
P/N 1011287 Rev. E 02/18
Apply only 1 drop of Loctite (RED) to front of the fan after
assembly. The outer edge of fan blade hub to be flush with
end of motor shaft.
3/16”
(4.75 mm)
Apply Loctite (BLUE) on setscrew of sprocket and all other
mounting screws.
Figure 11. Replacing Drive Motor and Fan Blade
Figure 10. Replacing Drive Motor and Fan Blade
POWER
TEMP
DOWN
TEMP
UP TEMP
SCALE
˚C
˚F
Fan Blade
Motor Sprocket
Drive Motor/Gear Reducer - Place 1 drop of
Loctite (Blue) into each threaded mounting
hole of reducer before installing.
Drive Motor
Bracket
Mounting
Bracket Screw
Motor Mounting
Screw
Mounting
Bracket
REPLACING CONVEYOR BELT CHAINS
1. Remove the old Conveyor Belt chain as described
previously on page 10.
2. Place the replacement Conveyor Belt Chain on
the top sprockets. Check for correct positioning
(Figure 8).
NOTE: Install conveyor belt so that the ends of the
hooks are facing down.
3. Wrap the Conveyor Belt chain around the lower
sprockets and hook both ends of the Conveyor
Belt chain together. A needle-nose pliers may be
required.
4. Reinstall the front and rear Conveyor Covers,
Release Sheet and Heat Shield.
Replacing Roller Tensioners
1. Push down on retaining tab of the tensioner.
2. While keeping pressure on the retaining tab, slide
the tensioner out of the retainer plate.
3. Replace the tensioner by sliding the new one into
the retainer plate.
Replacing Conveyor Motor and Fan Blade
NOTE: A small amount of Loctite (Blue & Red) is
required for proper gear motor installation.
1. Remove control cover.
2. Disconnect the motor wires and remove the
drive motor and drive motor bracket (Figure 10).
Discard the 8-32 x 5/16” mounting bracket screws.
3. Remove the motor sprocket using a hex wrench.
4. Remove the drive motor bracket from the gear
motor. Save the four 10-32 x 3/8” pan head
screws.
5. Place one drop of Loctite (Blue) into each thread-
ed hole in the gear reducer casting. Attach the
drive motor bracket to the gear reducer using the
original four 10-32 x 3/8” screws removed in step
3.
6. Attach the motor sprocket to the gear reducer as
shown in Figure 10.
NOTE: Be sure sprocket setscrew is positioned on
the flat of the gear reducer shaft. Maintain the 3/16”
dimension as shown in Figure 11. Apply Loctite
(Blue) to threads of setscrew and tighten securely.
7. Using the four new 8-32 x 5/16” stainless steel
SEMS truss head screws, attach the drive motor
bracket to the mounting bracket. DO NOT tighten
screws at this time.
8. Place the drive chain on the sprocket and push
down on motor. Allow 1/4” (0.6 mm) play at mid-
dle of drive chain, then tighten mounting screws
while holding motor. Check drive chain play after
tightening screws.
9. Re-connect motor wires, one at a time.
10. Re-install control cover.
MAINTENANCE (continued)

VERTICAL CONTACT TOASTER
12 P/N 1011287 Rev. E 02/18
TROUBLESHOOTING
WARNING
To avoid possible personal injury and/or damage to the unit, inspection, test and repair of electrical equip-
ment should be performed by qualified service personnel. The unit should be unplugged when servicing,
except when electrical tests are required. Use extreme care during electrical circuit tests. Live circuits will
be exposed.
Problem Possible Cause Corrective Action
No heat and conveyor
belts do not move.
Toaster is installed incorrectly. Perform the installation and operating procedures
found in the Installation section of this manual.
Not enough voltage, defective
power cord, defective rocker
switch.
Contact your Maintenance Person or Antunes
Technical Service for service.
Hi-limit switch tripped open. Reset hi-limit switch.
Wiring problem. Contact your Maintenance Person or Antunes
Technical Service for service.
No heat and conveyor
belts move.
Wiring problem. Contact your Maintenance Person or Antunes
Technical Service for service.
Inoperative platen. Contact your Maintenance Person or Antunes
Technical Service for service.
Platen is hot and the
Conveyor Belt chains are
not rotating.
Toaster is installed incorrectly. Refer to the Installation and Operation sections of this
manual for proper installation and operating proce-
dures.
Wiring problems. Contact your Maintenance Person or Antunes
Technical Service for service.
Drive motor inoperable or
incorrect conveyor drive motor.
Contact your Maintenance Person or Antunes
Technical Service for service.
Broken Drive Chain or loose
sprocket.
Check the Drive Chain for kinks, broken or bent links,
or other damage. Check the motor sprocket and
drive sprockets (on drive shaft); tighten setscrew on
flat of shaft if required. Check for damaged/worn
sprockets and replace as required.
Heat Shield not installed or
installed incorrectly.
Install the Heat Shield so that it activates the
Conveyor Interlock Safety Switch. If the Interlock
Switch has failed, order kit 7001436 to remove and
bypass the Interlock Switch.
Conveyor Belt chains installed
incorrectly.
Install the Conveyor Belt chains according to the
Maintenance Section of this manual. Be sure that
ends of the hooks are facing down.
Conveyor Interlock Safety
Switch is not activated.
Install the Heat Shield so that it activates the
Conveyor Interlock Safety Switch. If the Interlock
Switch has failed, order kit 7001436 to remove and
bypass the Interlock Switch.
Roller Tensioner Assembly or
Tensioner bent or missing.
Replace Roller Tensioner assy(s). or tensioners if
damaged or loose. Replace slide rails if worn or
missing.
Conveyor Belt chains too
loose or missing links (41 links
required when new). When
new, conveyor has 37 large
links and 4 small links.
Adjust or replace the Conveyor Belt chains according
to the Maintenance section of this manual.

VERTICAL CONTACT TOASTER
13
P/N 1011287 Rev. E 02/18
Problem Possible Cause Corrective Action
Product is over-toast-
ed, Platen heat is too
high, or drop time is
too slow
Temperature set too high. Set temperature control at a lower setting.
Bun Thickness Adjustment
Control knobs set incorrectly.
Measure bun thickness and set bun adjustment controls
correctly.
Buns sticking on Release
Sheet.
Clean or replace the Release Sheet or conveyor belt wrap.
Conveyor Covers not installed. Install the Conveyor Covers.
Conveyor Belts chains
installed incorrectly
Reinstall Conveyor Belt.
Defective Platen. Contact your Maintenance Person or Antunes Technical
Service for service.
Defective or wrong drive
motor.
Contact your Maintenance Person or Antunes Technical
Service for service.
Defective Drive Chain or loose
sprocket.
Check drive chain for kinks, broken or bent links or other
damage. Check motor sprocket and drive sprockets (on
drive shaft); tighten setscrew on flat of shaft if required.
Check for damaged/worn sprockets and replace as
required.
Wiring problem. Contact your Maintenance Person or Antunes Technical
Service for service.
Conveyor belt too loose or
missing links (41 links required
when new). When new, con-
veyor has 37 large links and 4
small links.
Remove conveyor belt. Lay belt flat and count links. Replace
entire belt if links are damaged. If conveyor belt has too
much play, it will jam. Adjust belt length as described under
Servicing the Conveyor Belt.
Product is over-toast-
ed or platen heat is
too high or drop time
is too slow.
Roller Tensioner assy(s). or
tensioner bent or missing.
Replace Roller Tensioner assy(s). or tensioners if dam-
aged or loose. Replace slide rails if worn or missing.
Bun adjustment controls set
incorrectly.
Measure bun thickness and set bun adjustment controls
correctly.
Product is under
toasted or platen
heat is too low or
drop time is too fast.
Not enough voltage, defective
power cord, defective rocker
switch.
Contact your Maintenance Person or Antunes Technical
Service for service.
Wiring problem. Contact your Maintenance Person or Antunes Technical
Service for service.
Platen inoperative. Contact your Maintenance Person or Antunes Technical
Service for service.
Conveyor drive motor inop-
erative or incorrect conveyor
motor installed in toaster.
Contact your Maintenance Person or Antunes Technical
Service for service.
Product is getting
stuck or conveyor
belts stop when prod-
uct is toasting.
Bun adjustment controls set
incorrectly.
Measure bun thickness and set bun adjustment controls
correctly.
Conveyor release sheet not
clean or missing.
Clean respective items. Refer to the Maintenance section
of this manual.
TROUBLESHOOTING (continued)

VERTICAL CONTACT TOASTER
14 P/N 1011287 Rev. E 02/18
TROUBLESHOOTING (continued)
Problem Possible Cause Corrective Action
Product is getting stuck or
conveyor belts stop when
product is toasting.
Not enough voltage, defective
power cord or rocker switch.
Contact your Maintenance Person or Antunes
Technical Service for service.
Wiring problem. Contact your Maintenance Person or Antunes
Technical Service for service.
Conveyor drive motor inop-
erative or incorrect conveyor
motor installed on toaster.
Contact your Maintenance Person or Antunes
Technical Service for service.
Conveyor Belt chain is loose,
worn, or broken or the motor
drive sprocket is loose..
Check drive chain for kinks, broken or bent links
or other damage. Check motor sprocket and drive
sprockets (on drive shaft); tighten setscrew on flat of
shaft if required. Check for damaged/worn sprockets
and replace as required.
The Conveyor Covers are not
installed or are improperly
installed.
Install conveyor cover assy(s).
Conveyor Belts chains are
installed incorrectly.
Reinstall conveyor belt.
Conveyor Belt Chains are
too loose or are missing links
(41 links required when new).
When new, the Conveyor Belt
chain has 37 large links and
4 small links.
Remove conveyor belt. Lay belt flat and count links.
Replace entire belt if links are damaged. If conveyor
belt has too much play, it will jam. Adjust belt length
as described under Servicing the Conveyor Belt.
The Roller Tensioners or
Tensioners are bent or miss-
ing.
Replace Roller Tensioner assy(s). or tensioners if
damaged or loose. Replace slide rails if worn or miss-
ing.

VERTICAL CONTACT TOASTER
15
P/N 1011287 Rev. E 02/18
TROUBLESHOOTING (continued)
Problem Possible Cause Corrective Action
Conveyor belts are
“jumping” or “snapping”.
Toaster is installed incor-
rectly.
Perform installation and operating procedures.
Bun adjustment controls set
incorrectly.
Measure bun thickness and set bun adjustment con-
trols correctly.
Conveyor drive motor inop-
erative or incorrect conveyor
motor installed on toaster.
Contact your Maintenance Person or Antunes
Technical Service for service.
Conveyor drive chain loose,
worn or broken. Loose
motor drive sprocket.
Check drive chain for kinks, broken or bent links
or other damage. Check motor sprocket and drive
sprockets (on drive shaft); tighten setscrew on flat of
shaft if required. Check for damaged/worn sprockets
and replace as required.
Conveyor belts installed
incorrectly.
Install conveyor belt to match diagram in Fig. 8 (page
10). Be sure that ends of the hooks are facing down.
Conveyor belt too loose
or missing links (41 links
required when new). When
new, conveyor has 37 large
links and 4 small links.
Remove conveyor belt. Lay belt flat and count links.
Replace entire belt if links are damaged. If conveyor
belt has too much play, it will jam. Adjust belt length
as described under Servicing the Conveyor Belt.
Roller Tensioner assy(s). or
tensioner bent or missing.
Replace Roller Tensioner assy(s) or tensioners if
damaged or loose. Replace slide rails if worn or
missing.
Crown and/or heel must
be forced into toaster.
Heat shield improperly
installed.
Crown and/or heel improp-
erly inserted into toaster.
Remove and reposition heat shield.
Buns must be inserted with cut faces facing each
other; heel in front slot and crown in rear slot.

VERTICAL CONTACT TOASTER
16 P/N 1011287 Rev. E 02/18
WIRING DIAGRAM
For Mfg. No. 9200641 & 9200642 (with Interlock Switch)
For Mfg. No. 9200643 (with Interlock Switch)

VERTICAL CONTACT TOASTER
17
P/N 1011287 Rev. E 02/18
WIRING DIAGRAM (continued)
For Mfg. No. 9200641 & 9200642 (without Interlock Switch)
For Mfg. No. 9200643 (without Interlock Switch)

VERTICAL CONTACT TOASTER
18 P/N 1011287 Rev. E 02/18
1 0011266 Conveyor Belt 2
0800204 1/2” Pitch Link, Small 4
0800121 3/4” Pitch Link, Large 38
2 2150117 Idler Shaft 2
3 0011375 Conveyor Cover Assy. 2
(Mfg. No. 9200641 & 9200642)
0011329 Conveyor Cover Assembly 2
(Mfg. No. 9200643)
4 0010475 Tensioner Assy. (Incl. #40, 76, 85) 4
5 0800406 Rod, Conveyor Cover 4
6 2150190 Sprocket 8
7 7000199* Spacer Kit 2
8 0503362 Control Cover 1
9 2150118 Drive Shaft 2
10 0700463 Power Cord/Plug, NEMA 5-15P 1
(Mfg. No. 9200641)
0700453 Power Cord/Plug, CEE 7/7 1
(Mfg. No. 9200642 & 9200643)
11 4030355 Thermostat, 122° F - 600° F 1
12 2150158 Ball Bearing 2
13 2150186 Bearing 6
14 0500464 Bearing Retainer/Spacer 1
15 0503376 Bearing Retainer 6
16 7000167 Bearing and Retainer Kit 1
17 2150181 Drive Sprocket 2
18 2150187 Drive Chain 1
19 0011299 Idler Sprocket & Bearing 1
20 0501232 Bracket, Idler Sprocket 1
21 0503589 Bracket, Motor Mounting 1
22 7000282 Drive Motor Kit (Mfg. No. 9200641) 1
7000240 Drive Motor Kit 1
(Mfg. No. 9200642 & 9200643)
23 2150132 Sprocket, Motor 1
24 7000882 Rocker Switch Kit, On/Off 1
25 4060355 Terminal Block 1
26 0503495 Retainer, Tension Bracket, RH 2
27 0503507 Retainer, Tension Bracket, LH 2
28 4060323 Indicator Light, Amber (125V) 1
(Mfg. No. 9200641)
4060229 Indicator Light, Amber (250V) 1
(Mfg. No. 9200642 & 9200643)
29 0013373 Roller Tensioner Assy. 2
30 0021951 Tensioner Bracket Weldment, Right 2
31 0021952 Tensioner Bracket Weldment, Left 2
32 1000899 Label, Control 1
33 10P1047* Label, Dial (Pack of 10) 1
34 2100253 Knob, Cam 2
35 0503390 Cover, End Housing 1
36 2100133 Knob, Thermostat Control 1
37 0021170 Weldment, End Housing 1
38 7000249 Release Sheet (Pack of 3) -
7000250 Release Sheet (Pack of 10) -
39 0021194 Weldment, Control Housing 1
40 7000121 Slide Rail Kit (Incl. Qty. 2
slide rails for tensioners) 2
41 0021207 Conveyor Cam 2
42 7000176 Thermocouple Retainer Kit 2
43 4030332 High Limit Thermostat 1
44 0400315 Strain Relief 1
45 0400138 Locknut, 1/2” 1
46 0503590 Bracket, Motor 1
47 0070640 Wire Set (Not Shown) 1
(Mfg. No. 9200641 & 9200642)
0700641 Wire Set addendum (Not Shown) 1
(Mfg. No. 9200641 & 9200642)
0700920 Wire Set (Not Shown)
(Mfg. No. 9200643) 1
48 0503385 Bun Chute 1
50 331P101* Nut, Hex, 5/16 x 18” 1
51 7000229 Platen (120 Volt) 1
(Mfg. No. 9200641)
7000200 Platen (208-240 Volt) 1
(Mfg. No. 9200642 & 9200643)
53 4010107 Interlock Switch (some models) 1
57 0503608 Cover Plate 2
59 2100256 Tape, Hi-Temp 8
61 212P118* Flat Washer, 5/16” 1
62 0500464 Retainer, Bearing 1
64 0011330 Heat Shield Assy. 1
(Mfg. No. 9200641 & 9200642)
0013013 Heat Shield with Dampers 1
(Mg. No. 9200643)
65 325P163 Setscrew, 1/4-28 x 5/16” 1
66 10P1192* Label, Caution Hot 1
67 308P157* SCR, TAP #08-32 x 3/8” 1
PHTRSHD; “F” 410 S/S
68 306P104* Screw, #6-32 x 1/4” 1
69 406P107* Cable Tie 1
70 308P143* Nut, #8-32, “KEPS” 1
71 310P103* Screw, #10-32 x 1/4” 1
72 310P140* Washer, #10 1
74 306P101* Nut, Hex, #6-32 1
75 306P123* Screw, #6-32 x 7/8” 1
77 100P900* Label, Service 1
78 325P104* Washer, 1/4” 1
79 325P109* Screw, 1/4-20 x 1/2” 1
80 308P124* Screw, 1-Way, #8-32 x 1/2” 1
81 210K230 Bumper, Recess Leg, 1” 1
82 310P136* Screw, #10-32 x 1-1/4” 1
84 308P203* Screw, #8-32 x 3/8 1
With Int. Tooth Washer
85 308P181* Screw, Flat Hd., #8-32 x 3/8” 1
86 218P145* Cover, Leg, Bumper 1
87 331P103* Shoulder Bolt, 5/16-18 x l” 1
88 306P105* Screw, #6-32 x 1/2” 1
89 0503455 Tension Spring, Inner 4
90 2100259 Slide Bar 4
* Only available in packages of 10.
Item Part No. Description Qty. Item Part No. Description Qty.
REPLACEMENT PARTS (continued)

VERTICAL CONTACT TOASTER
19
P/N 1011287 Rev. E 02/18
REPLACEMENT PARTS (continued)
CAUTION
3
3
8
35
10
44
64
38
34
33
66
67
39
45
81
86
82
77
29

VERTICAL CONTACT TOASTER
20 P/N 1011287 Rev. E 02/18
PARTS (continued)
21
70
87
17
19
70
20
61
57
50
72
12
12
62
17
70
72
18
19
17
23
17
15
70
59
13
14 16
80
75
70
25
74
42
67
67
70
42
67
67
53
23
67 46
22
84
43
11
24
32
39
28
36
83
57
NOTE: As of March 2017, the Interlock
Switch (item 53) is discontinued from
use. If your toaster has the Interlock
Switch and it fails, order kit 7001436
to remove and bypass the Interlock
Switch.