Aosom 370-301V80 User manual

1
370-301V80
IN230800427V01_US_CA
Electric Ride-on Car
Voiture-jouet électrique
EN_IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
FR_IMPORTANT : A LIRE ATTENTIVEMEN ET A CONSERVER POUR VOUS Y REFERER
ULTERIEUREMENT.
● 2.4G remote control
● Music
● Light control
● Forward and backward
● Five Points Safety Belts
● Télécommandes 2,4G
● Musique
● Contrôle de la lumière
● Marche avant et arrière
● Ceintures de sécurité à cinq points

2
L1
K2
J19
I1
E2 D2
C2
B2 A1
H1 G2
F1
Car body Motor Motor cover
Wheel Drive Wheel Rear part
Armrest Backrest M8 Spanner
M4×12 flat head screws M4×12 round head screws Charger
Manual Remote control Mp3line
O1 N1
M1
EN

3
Product Specifications:
Battery:
Drive Motor:
Suitable age:
Maximum weight:
Car Size:
Speed:
Hours of Use:
Charger:
Remote Control Battery:
12V 4.5AH
12V390*2
18+ months
25kg
74*59*46cm
3 km/h
Using 0.8 hours after Charging 8-10 hours
Input: 100V-240V 50/60Hz
Output: 12V 0.5A
AAA1.5V*2(not provided)

4
Backward
Pairing Speed
Right
Speed indicator light
Left
Brake
Forward
Function
Music switch/Volume -
Pause/play
Music switch/Volume +
Music power switch
Button function
Light control switch
Charging hole
Power switch
● Features
- Supply Voltage: 2X1.5V
- Frequency: 2.4GHz
Instruction for 2.4G remote control
● When moving, never switch between forward and backward – this can damage the
gearbox and motor.
● The remote control requires a battery.
● Only and adult should use the remote control.
● This product is mainly operated by the remote control.
● Button Description
- Forward: Direct the ride- on car to move
forward.
- Backward: Direct the ride-on car to move
backward.
- Pairing: Pair the ride-on car with a
remote controller.
- Left: Direct the ride- on car to turn left.
- Right: Direct the ride- on car to turn right.
- Speed: Adjust the speed of the ride- on car’ s movement as low, moderate or high.
- Brake: Immediately stop the ride-on car and lock the car until released.

5
● Pairing Instruction
1. Turn on the power of the ride-on car, press and hold the pairing button until the
speed indicator light switches on without flashing.
2. Release the pairing button, and the speed indicator light will switch off.
3. If the speed indicator light switches on again, then the pairing is successful; if not,
please repeat steps 1 and 2.
4. One successful pairing is all, and no more pairings are needed in later use
● Battery installation
Open the back cover of the remote control with screwdriver and insert two triple A
batteries (AAA 1.5V). Please pay attention to the polarity. Close the back cover and
tighten the screws when the LED light is on, indicating battery installed properly.
Battery needs to be replaced when the LED light dims or blinks.
1.Install the wheel
Insert the caster wheel into the slot on the baseboard, following the direction indicated
by the arrow. Then, secure it using an M4×12 screw.
Battery specifications
● Never mix new, old or different types of batteries together.
● Never mistake positive and negative electrodes of a battery – this could lead to a
short circuit.
● Do not charge non-rechargeable batteries.
● Place batteries into the right polarity.
● Only adults should charge and change batteries.
● Take batteries out of the product when charging.
● Take dead batteries out of the product – keep out the reach of children.
● Use a screwdriver to remove the battery screws, open the cap as the arrow signals,
then insert two AAA 1.5V batteries.
J
J
J
J

6
2. Install the motor and drive wheel
First remove the three clamps securing the rear axle to the baseboard. Sequentially
place the motor, drive wheel, and washer on both sides of the rear axle. Secure them
with nuts. Next, connect the wire terminals of the motor to the connector cables and
feed them through the wiring holes in the baseboard. Finally, insert the rear axle and
motor back into the baseboard.
BE
E
I
I
3. Fixed pressure plate, motor cover, rear parts
According to the diagram, secure the pressure plate to the base plate using M4×12
screws.
According to the diagram, secure the motor cover to the base plate using M4×12
screws.
According to the diagram, secure the rear parts to the base plate using M4×12 screws.
JJJJ
J

7
4.Connect the power cable
Unscrew the bolts on the seat cushion, open the seat cushion, and according to the
diagram, plug the terminals of the power connection cable into each other.
5.Install the armrest assembly
First, remove the screws from the backrest. Then, pry the armrest supports outward.
With one hand, pull the backrest support outward and hold it firmly in place. Next,
align the armrest assembly with the screw posts on the backrest and snap it into
place. After it's snapped in, first slide the backrest support into the screw posts, then
snap the armrest support into the screw posts, and secure with screws.
G
H
J
J
J

8
6. Install the backrest assembly
Insert the assembled backrest component into the vehicle body in the direction
indicated by the arrows, and snap it into place. Then, secure it using M4×12 flat head
screws and M4×12 round head screws.
J
J
KK
7.Install the forward reverse switch
Install the forward-reverse switch in the direction indicated by the arrows. Once it's
properly in place, secure it using M4×12 flat head.
J
JJ
J

9
WARNING
- This product must be assembled by an adult.
- When unassembled, this product contains small and sharp parts – keep out the reach
of small children.
- Do not use in traffic.
- The seatbelt must be worn when using this product.
- Adult supervision is required when using this product.
- Battery must be charged by an adult. Charge the product before its first use.
- Keep packaging out the reach of children to avoid suffocation.
- Only use parts provided by the manufacturer.
- Ensure children do not play with the charger.
- Do not use in congested streets, roads, slopes or near drains.
- Do not change the circuit or add electrical devices to the product.
- Keep the car away from water and other liquids to avoid damage.
- The maximum load is 25kg – this product can be used by one child at a time.
- Ensure the power is switched off when not in use. Remove the battery connector
when it has not been used for a while.
- Before using and charging, check the plug and other parts for any damage.
Charging:
- Charge the battery for less than 10 hours – charging for longer can cause permanent
damage.
- Place the DC plug into the power socket, then put the charger into the plug. Never
use the product when charging.
- This product can be used for one hour – the charging time is 8-10 hours.
- It is normal for charger and battery to stay cool when charging.
- Do not use the connector near water to avoid damage.
- Only use the supplied charger. Using a charger not supplied by the manufacturer can
damage the product.
- When not in use for a long time, charge the product.
Note

10
Charging steps:
Step 1: The charging hole is under the seat.
Step 2: Insert the plug into the hole.
Step 3: Connect the charger to the power socket.
Warning: Car must be charged by adults only. Car is useless during charging.
Troubleshooting
Problem Cause Solution
- The battery is low.
- Failure to press the switch
button correctly.
- Power connector failure.
- Battery breakdown.
- Electrical devices are
damaged.
- Generator is faulty.
- Ensure battery is fully
charged.
- Follow instructions when
using this product.
- Reinstall the power
connector.
- Change battery.
- Change electrical devices.
- Change generator.
The car does not start.
The battery does not
charge.
- Battery connector failure.
- Charger doesn't charge.
- Faulty charger.
- Reinstall the connector.
- Plug in the charger again.
- Change the charger.
The car doesn't drive
far. - Battery isn't fully charged.
- Overused battery.
- Ensure the battery is fully
charged.
- Change the battery.
There's a slight noise
and the car heats
when charging. - This is normal. - Nothing needs to be done.
The car operates at a
slow speed.
- Overused battery.
- The battery is dead.
- The product has exceeded its
maximum load.
- Uneven driving surface.
- Change the battery.
- Ensure battery is fully
charged.
- Ensure the weight is below
25kg.
- Drive on a flat and even
surface.