Apevia X-Discovery User manual

X-Discovery Series Installation Guide
1:Unscrew the thumb screws 2.Pull the side panel back then 3:Find the motherboard stand-offs
from Side Panel. pull out. from the enclosed screw box.
4:Put the motherboard stand-offs 5.Sit the motherboard on the 6.Find screws in the screw box.
on the motherboard tray. motherboard tray.
7.Screw in all the screws into the 8.Same as Step 7.
motherboard stand-offs

9.Take out front panel:(You need to take out both side panels first to unscrew front panel screws)
Step (1): Unscrew both side Step (2): Take out both side Step (3): There are 4 screws that
panels panels holdthe front panel to the case. (2
on each side) Unscrew 2 screws from
the back of front panel on one side.
Step (4): Unscrew the other Step (5): Pull out the front 10.Front Case Fans (Optional):
2 screws from the other side. panel from the bottom. You can put up to 2*80mm fans
in the front.
11.Force out the 5.25” metal 12.Screw all 5.25” drives 13.3.5” External Drives:
plate from inside with a screw in place. Force/push out 3.5” metal plate
driver, then insert 5.25” drive. and install 3.5” external drives.

14.3.5” Internal Drives: 15.Screw all 3.5” hidden drivers 16.Put the front panel back
Install 3.5” hidden drivers such in place. and screw back the 4 screws
as hard drive and zip drive. to secure the front panel.
17.Find the 20pin/or 24pin main 18.Plug into your motherboard. 19.Find the 4-pin P4 connector
connector from Power Supply. Different M/B has different layout. from power supply.(for P4 only)
IfyouhaveAMDorP3board,
Youdonotneedtoconnectit.
20.Plug into your motherboard. 21.Find 2*USB Cables.(USB1 22.Plug USB cables to your M/B.
(For Intel P4 motherboard only) & USB2) Please refer to M/B User Manual.
Please refer to M/B user manual.

23.Find “HDD LED” and 24.Plug them onto your M/B. 25.Find “Power SW” and “+P LED”
“Reset SW” cables. Please refer to M/B user manual. “-P LED” cables and plug onto M/B.
PleaserefertoM/Busermanual.
26.Find “Case Speaker” from 27.Install case speaker onto M/B 28. Install LED Lights: Find 2*
screw box. following M/B user manual. LED connectors from the front
Panel. They are 2*2-pin connectors
that lead out to 2*4-pin connectors
(1*Male, 1*Female)
29.Connect the 4-pin Male connector
to a 4-pin connector Female from
power supply.

30.Install LCD Temperature Readout:
Step (1): Connect 4-pin Male Step (2): Remove the protective Step (3): This is the temperature
connector from LCD to a 4-pin plastic tube from the sensor. sensor. It’s very fragile. Be gentle.
Female connector from Power Supply. tube from the sensor. from power supply.
31.You can either tape the sensor on hard drive or on CPU Heat 32.Once powered on, the LCD shows
sink or leave it inside the case to get the overall system temperature. temperature readout with back lighting.
33.Find “Case Feet” in the screw box. 34.View from side window panel
Lay case down and put “Case Feet” on. After installation.
Note:
1.You can link together all the 4-pin connectors(male to female) from all the case fans, LCD, LED, HDD and
just use one of the 4-pin Molex connectors from power supply. That will leave you more 4-pin Molex connectors
from your power supply for other devices.