Apevia X-Navigator User manual

X-Navigator Installation Guide: (All screws for MB, DVD, HDD and case keys are provided in Tool Box)
1.Install Motherboard, 3.5” & 5.25” Drives:
1.1.Remove two thumb screws 1.2.Install brass standoffs on the 1.3.Place your motherboard on
from the back of the side window. right solid panel for MB.(Some the brass standoffs. Screw in
Push the handle towards front motherboards have different your motherboard to standoffs
panel a bit, then pull it out. layout. Please refer to MB manual. with motherboard screws.
1.4.Remove 3.5” HDD Cage. 1.5.Put the 3.5” HDD Cage 1.6.Attach drive rails on both sides of
Install 3.5” drives to the cage. back in place. 5.25” drives. (You can rails mounted
on the bottom of the case)
1.7.Remove the 5.25” bay covers. 1.8.Slide 5.25” drive into its bay.
Insert your index finger on the side,
push with pressure to the left and
and pull out as shown on the picture.

2.Install Power Connection, LED’s and Front Panel Leads, USB and 1394 Firewire Cables:
2.1.Install 20-pin cable connector from power 2.2.Install 4-pin cable connector to motherboard.
supply to motherboard. Please refer to MB manual (This is for P4 MB only) Some P4 motherboards may
not need to install this. Please refer to MB manual.
2.3.Connect 4-pin cable connectors from 2.4.LED’s and Front Panel Leads-Power SW,
power supply to all 3.5” and 5.25” devices. Power LED, HDD LED, Reset SW and Speaker.
2.5.Connect LED’s and Front Panel Leads to MB 2.6.Find USB pin position from your MB manual.
-Power SW: Connect to MB “PWR” Connect USB cable to USB header on MB.
-Power LED: Connect to MB “PLED”
-HDD LED: Connect to MB HDD/IDE LED connector
-Reset SW: Connect to MB “RSW”
-Speaker: Connect to MB 4-pin connector
2.7.IEEE1394 Firewire cable connector
(9-pin consists of 6 wires). Please refer to
MB user’s manual.

3.Install Fan Speed Controller, Fan Connectors, Front LED Lights, LCD and Temp. Sensors:
3.1.Find the two black-and-yellow cable connectors 3.2.Connect the INPUT connector to PSU
from front panel, one with INPUT CD 12V, the 4-pin connector.
other with OUTPUT 0.3A 5 FAN MAX 1.2A.
These two connectors are for Fan Speed Connector
and fan connection
.
3.3.Linke all 5 fans(2*Back Fans, 1*Side Window Fan, 3.4.Find green-and-white 2-pin cable connector for
1*Front Fan, 1*Top Fan) together(Male to Female). LED. Then, find the black-and-red twisted 4-pin
Then connect 1*4-pin Male end to OUTPUT 0.3A cable connectors for LCD. Connect the LED 2-pin
5 FAN MAX 1.2A Connector. Male connector to LCD 4-pin Female connector.
3.5.Then, connect the 4-pin Male connector 3.6.There are two temperature sensors for front LCD
for LCD to PSU 4-pin Female connector. temperature readout. You can tape the sensor to Heatsink
to detect CPU temperature, or tape on HDD to detect
HDD temp, or just let it hang inside the case to monitor
overall system temperature.

4.How to take out and insert Front Decorative Masks:
4.1.Take out the Front Decorative Masks:
4.1.1.Open the front door. 4.1.2.Pull the Mask upward to 4.1.3. Press down the upper clip
Press down the upper clip and take it out. and squeeze the side clips from
pull out the upper part the back of the front door, then
pushthemout.
4.2.Insert the Front Decorative Masks
4.1.4.Pull out the upper Mask 4.2.1.Open the Front Door. 4.2.2.Then, snap in the Side
Insert the Bottom Mask first. Clips into the holes.
Snap in bottom clip into the hole.
4.2.3.Push down on the upper 4.2.4.Close the front door to 4.2.5.Once the upper and side
clip to fit into the hole. Push in. insert Upper Mask. Snap in clips are in, then snap the
upper clip, then the side clips. bottom clip in.

X-Navigator Series USB/1394 cable pin assignment
Cable Cable Color Function
RED +5V
WHITE -D
GREEN +D
USB 2.0
BLACK GND
WHITE VP
BLACK VG
RED TPB-
GREEN TPB+
BROWN TPA-
1394
BLUE TPA+