Apevia X-Plorer ATXB8KLW Series User manual

ATXB8KLW(X-Plorer) Series Installation Guide
1:Unscrew the thumb screws 2.Pull the side panel back then 3:Find the motherboard stand-offs
from Side Panel. pull out. from the enclosed screw box.
4:Put the motherboard stand-offs 5.Sit the motherboard on the 6.Find screws in the screw box.
on the motherboard tray. motherboard tray.
7.Screw in all the screws into the 8.Same as Step 7.
motherboard stand-offs

9.Take out front panel: (Optional. Only if you need to install front fans or replace LCD)
Step (1): Unscrew the side panel Step (2): Take out the side Step (3): There are 4 screws that
panel (motherboard side) panel (motherboard side) hold the front panel to the case. (2
on each side) Unscrew the 2 screws
from inside of the case.
Step (4): Unscrew the other Step (5): Pull out the front 10.Front Case Fans (Optional):
2 screws from the other side. panel from the bottom. You can put up to 2*80mm fans
in the front.
11.Put the front panel back 12.5.25” Drives: Open the door 13.Insert 5.25” drivers.
and screw to secure. and force out the 5.25” metal
plate and drive cover from inside
with a screw driver.

14.Screw all 5.25” drives 15.3.5” External Drives: 16.Insert external 3.5” drives
in place. Force out 3.5” metal plate and and secure with screws in place.
drive cover with a screw driver.
17.3.5” Internal Drives: 18.Screw all 3.5” hidden drivers 19.Find the 20-pin connector
Install 3.5” hidden drivers such in place. from Power Supply.
as hard drive and zip drive.
20.Plug into your motherboard. 21.Find the 4-pin P4 connector 22.Plug into your motherboard.
Different M/B has different layout. from power supply.(for P4 only) (For Intel P4 motherboard only)
Please refer to M/B user manual.

23.Find 2*USB Cables.(USB1 24.Plug USB cables to your M/B. 25.Find “HDD LED” and
& USB2) Please refer to M/B User Manual. “Reset SW” cables.
26.Plug them onto your M/B. 27.Find “Power SW” and “+P LED” 28.Find “Case Speaker” from
Please refer to M/B user manual. “-P LED” cables and plug onto M/B.screw box.
Please refer to M/B user manual.
29.Install case speaker onto M/B 30. Install LED Lights: Find 2* 31.Connect the 4-pin Male connector
following M/B user manual. LED connectors from the front to a 4-pin connector Female from
Panel. They are 2*2-pin power supply.
connectors that lead out to2*4-pin
connector (1*Male, 1*Female)

32.LCD Temperature Readout: 33.Remove the protective plastic 34.This is the temperature
Connect 4-pin Male connector from tube from the sensor. sensor. It’s very fragile.
LCD to a 4-pin Female connector Be gentle.
from power supply.
35.You can either tape the sensor on hard drive or on CPU Heat 36.Once powered on, the LCD
sink or leave it inside the case to get the overall system temperature. shows temperature readout with
backlighting
37.Fan Speed Controller: Find a 38.Link all case fans’ cables 39.Then connect the Male end to
4pin male connector from front together. There will be 1*Male a 4pin Female (output) from the
panel with “Input DC 12V” and and 1*Female left out at each front panel fan speed controller
connector it to a 4pin female end. unit.
connector from power supply.

40.Find “Case Feet” in the screw box. 41.View from side window panel
Lay case down and put “Case Feet” on. After installation.
Note:
1.You can link together all the 4-pin connectors(male to female) from all the case fans, LCD, LED, HDD and
just use one of the 4-pin Molex connectors from power supply. That will leave you more 4-pin Molex connectors
from your power supply for other devices.