Apevia X-Infinity ATXB6KLW Series User manual

ATXB6KLW(X-Infinity) Series Installation Guide
1:Unscrew the thumb screws 2.Pull the side panel back then 3:Find the motherboard stand-offs
from Side Panel. pull out. from the enclosed screw box.
4:Put the motherboard stand-offs 5.Sit the motherboard on the 6.Find screws in the screw box.
on the motherboard tray. motherboard tray.
7.Screw in all the screws into the 8.Same as Step 7.
motherboard stand-offs

9.Take out front panel: (Optional. Only if you need to install front fans or replace LCD)
Step (1): Unscrew the side panel Step (2): Take out the side Step (3): There are 4 screws that
panel (motherboard side) panel (motherboard side) hold the front panel to the case. (2
on each side) Unscrew the 2 screws
from inside of the case.
Step (4): Unscrew the other Step (5): Pull out the front 10.Front Case Fans (Optional):
2 screws from the other side. panel from the bottom. You can put up to 2*80mm fans
in the front.
11.Put the front panel back 12.5.25” Drives: Open the door 13.Insert 5.25” drivers.
and screw to secure. and force out the 5.25” metal
plate and drive cover from inside
with a screw driver.

14.Screw all 5.25” drives 15.3.5” External Drives: 16.Insert 3.5” external drives.
in place. Force out 3.5” metal plate and
drive cover with a screw driver.
17.Secure external 3.5” drives 18.3.5” Internal Drives: Install 19.Screw all 3.5” hidden drivers
with screws in place. 3.5” hidden drivers such as in place.
hard drive and zip drive.
20.Find the 20-pin connector 21.Plug into your motherboard. 22.Find the 4-pin P4 connector
from Power Supply. Different M/B has different layout. from power supply.(for P4 only)
Please refer to M/B user manual.

23.Plug into your motherboard. 24.Find 2*USB Cables.(USB1 25.Plug USB cables to your M/B.
(For Intel P4 motherboard only) & USB2) Please refer to M/B User Manual.
26.Find “HDD LED” and 27.Plug them onto your M/B. 28.Find “Power SW” and “+P LED”
“Reset SW” cables. Please refer to M/B user manual. “-P LED” cables and plug onto M/B.
PleaserefertoM/Busermanual.
29.Find “Case Speaker” from 30.Install case speaker onto M/B 31.Audio Cable: Take out the
screw box. following M/B user manual. only I/O slot with a hole.
.

32.Bring Audio Cables through 33.Find the know in audio cable 34.Plug audio cables to sound
the I/O slot and leave them and fit it into the hole in the I/O card or M/B.
outside of the case. Slot and screw I/O slot back.
35.Install LED Lights: Find 2* 36.Connect the 4-pin Male connector
LED connectors from the front to a 4-pin connector Female from
Panel. power supply. They are 2*2-pin
connectors that lead out to2*4-pin
connector (1*Male, 1*Female)
37.LCD Temperature Readout: 38.Remove the protective plastic 39.This is the temperature
Connect 4-pin Male connector from tube from the sensor. sensor. It’s very fragile.
LCD to a 4-pin Female connector Be gentle.
from power supply.

40.You can either tape the sensor on hard drive or on CPU Heat 41.This is how the front panel looks
sink or leave it inside the case to get the overall system temperature. like after power on.
42.Real Fan (Optional): You 43.Link all case fans’ cables 44.Find “Case Feet” in the screw box.
can install 1*80mm up to together. There will be 1*Male Lay case down and put “Case Feet” on.
120mm at rear. and 1*Female left out at each
end. Just connect the Male to
a 4-Pin Female connector from
the Power supply.
Note:
1.You can link together all the 4-pin connectors(male to female) from all the case fans, LCD, LED, HDD and
just use one of the 4-pin Molex connectors from power supply. That will leave you more 4-pin Molex connectors
from your power supply for other devices.