Aquadart Venturi 6 AQ9352S User manual

Item Number:AQ9352S
INSTALLATION INSTRUCTIONS www
Fixed Bath Screen
Tools Required
IMPORTANT
USE SAFETY EYE-WEAR WHEN DRILLING
Lifetime Product Guarantee
To activate your Product Guarantee please
visit www.aquadart.co.uk and complete
the online form.
6
PH2 TYPE
2.75
www.aprilproducts.co.uk
www.aprilproducts.co.uk
INSTALLATION INSTRUCTIONS
www.aquadart.co.uk
This product should be installed by a suitably qualified and proficient person. The fitting instructions should be
followed carefully to ensure a proper and safe installation. Failure to follow these instructions could result in future
injury.
These instructions and list of parts assume that installation is done against solid/tiled walls.
Please check this product for damage prior to starting the installation. No claims can be made after the product has
been fitted.
PLEASE NOTE :The minimum and maximum adjustment sizes noted on the product brochures are based on
perfectly plumb walls and trays.

COMPONENTS AND BOX CONTENTS
Box Contents
20
1
2
5
22
6
7
18
19
19
3
9
4
19
14
13
12
8
11
10
15
17 16
21
Wall
Profile
Description
Upright Profile
Qty
1
1
Frame Profile 1
SN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Connected Profile 1
3
3
1
Cover Cap
Screw Cover Cap
Cap
Profile Top Cap 1
Upright Seal 1
Bottom Seal
1
Pivot Part 1 2
Pivot Part 2
Pivot Part 3 2
2
Wall Plug
Screw ST3.5x10
Screw ST4x30
4
3
6
Fixed Glass Panel 1
Glass Shelf 1
Moving Glass Panel 1
Glass Clip A
Glass Clip B
Glass Clip Cover
19
20
21
22
2
2
1
Description Qty
SN

A
B
C
D
12-15mm
from the
bath edge
4x45mm screw
Ф6 drill bit
E
Ф2.75 drill bit
3.5x10mm screw
Step 1: Position the wall profile (1) onto the bath , approximately 12-15mm from the outside bath edge to ensure that
the screen runs along the inside edge of the bath rim. (A).
Step 2: Level the profile with a spirit level , then mark the position using a pencil. Mark through the 3 pre-drilled screw
holes in the wall profile. (B).
NOTE :You may find it easier to mark and drill the wall if you apply masking tape to it first.
Step 3: Drill the marked points using a 6mm masonry drill bit.
Step 4: Insert 3 wall plugs (18) into the wall holes , then secure the wall profile using 3 x ST4X45 screws (21). (C)
Step 5 : Carefully position the screen into the wall profile. (D)
Step 6 : Secure to the wall profile using 3 x ST3.5X10 screws (21) and cover caps (6) and (7). (E) (F)

Ф6 drill bit
5x50mm screw
Inside
Inside
Assemble The Glass Shelf

G
Allow 24 hours before use for silicone
to set.
For cleaning instructions see
guarantee.
Silicone the outside of the vertical wall
post and also the outside of the
bottom of the wall post as shown.
H
I
Seal
NOTE : To ensure a watertight seal ensure the bottom seal (No.10) is fully inserted into the base of the
hinge as per the above diagram.

o
Riverside Business Park,Royd Ings Avenue,Keighley, West Yorkshire,BD21 4AF
01535 613830 Technical:01535 613830 Fax: [phone]