Aquadart venturi 6 AQ9357LS User manual

Swiftseal Semi-Frameless 4 Fold Bath Screen
Tools Required
IMPORTANT
USE SAFETY EYE-WEAR WHEN DRILLING
6
PH2 TYPE
2.75 Drill bit
INSTALLATION INSTRUCTIONS www
www.aprilproducts.co.uk
www.aprilproducts.co.uk
INSTALLATION INSTRUCTIONS
www.aquadart.co.uk
AQ9357LS
AQ9357RS
This product should be installed by a suitably qualified and proficient person. The fitting instructions should be
followed carefully to ensure a proper and safe installation. Failure to follow these instructions could result in future
injury.
These instructions and list of parts assume that installation is done against solid/tiled walls.
Please check this product for damage prior to starting the installation. No claims can be made after the product has
been fitted.
PLEASE NOTE :The minimum and maximum adjustment sizes noted on the product brochures are based on
perfectly plumb walls and trays.

Box Contents
COMPONENTS AND BOX CONTENTS
Wall Plug
x3
Screw ST4x30
x3
Cover Cap
x1
Screw ST4x10
x3
Cover Cap A
x3
Cover Cup B
x3
x1
Bubble seal
End Cap
x1
Bottom Rail Holder
x1
Fixing Kit
Washer A
Washer B
Bolt
x1
x1
1
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
13
Screw M6x12
x2 x1
No. Qty No. Qty
1 Wall Profile 1 11 Arm Rail 1
2
Wall Plug
3
12
Bath Screen Assembly
1
3
Bolt
2
13
Fixing Screw M6x12
1
4
Fixing Screw ST 4x30
3
14
Cover Cap(For Rail Holder)
1
5
Cover Cap
3
15
Rail Holder Fixing
1
6
Fixing Screw ST 4x10
3
16
Washers
2
7
Cover Cup
3
17
1
8
Washer A
1
18
End Cap
1
9
Washer B
1
10 Bubble Seal(For Arm Rail) 1
Description
Bottom Rail Holder
Description

B
C
Ф6 drill bit
4x30mm screws
A
12-15mm
from bath
edge
Ф3 drill bit
4x10mm screws
DE
F
G
: Position the wall profile (No 1 ) onto the bath , approximately 12-15mm from the outside bath edge (Diagram A).
: Level the profile with a spirit level, then mark the position using a pencil through the 3 pre-drilled screw holes in the
wall profile,drill the marked points using a 6mm masonry drill bit. Once this is done insert 3 wall plugs(No.2) (Diagram B).
NOTE :You may find it easier to mark and drill the wall if you apply masking tape to it first.
: Secure the wall profile using 3 x ST4X30 screws (No.4) (Diagram C).
Step 4 : Push the bath screen assembly onto the wall profile (Diagram D). Ensure the bottom rail holder sits in the middle of
the groove of the end cap on the bottom arm rail.(Diagram E)
Step 5 : Drill 3 equally spaced holes with a 3mm drill bit through the wall profile into the frame(Diagram F)
Step 6 : Fix the bath screen assembly to the wall profile using the screws ST4 x10 (No.6). (Diagram G)
Step 1
Step 2
Step 3

Seal Outside
Seal Inside
To open the bath screen please follow the steps as below:
Press the bottom rail profile with a soft downwards motion to release it from the rail holder.(Diagram H ）
Lift the bottom rail to rotate it into the wall profile channel(Diagram I), then you can open/close the bath
screen.
24 HRS
DO NOT USE THE
ENCLOSURE FOR
24 HOURS AFTER
SEALING
Applying Silicone Sealant
Sealing Inside
Seal from the top of the wall profile to the bottom on the INSIDE
between the wall profile and the wall.
IMPORTANT: Do not apply sealant on inside of the bath.
Sealing Outside
Seal from the top of the wall profile to the bottom between the
wall profile and tiles.
HI

o
Riverside Business Park,Royd Ings Avenue,Keighley, West Yorkshire,BD21 4AF
01535 613830 Technical:01535 613830 Fax: [phone]