Aquadart venturi 6 AQ9359S User manual

AQ9359S-Swiftseal Single Bath Screen
Tools Required
IMPORTANT
USE SAFETY EYE-WEAR WHEN DRILLING
6
PH2 TYPE
2.75
INSTALLATION INSTRUCTIONS www
www.aprilproducts.co.uk
www.aprilproducts.co.uk
INSTALLATION INSTRUCTIONS
www.aquadart.co.uk
This product should be installed by a suitably qualified and proficient person. The fitting instructions should be
followed carefully to ensure a proper and safe installation. Failure to follow these instructions could result in future
injury.
These instructions and list of parts assume that installation is done against solid/tiled walls.
Please check this product for damage prior to starting the installation. No claims can be made after the product has
been fitted.
PLEASE NOTE :The minimum and maximum adjustment sizes noted on the product brochures are based on
perfectly plumb walls and trays.

Box Contents
COMPONENTS AND BOX CONTENTS
Wall Plug
x3
Screw ST4x30
x3
Cover Cap
x1
Screw ST4x10
x3
Cover Cap A
x3
Cover Cup B
x3
x1
Bubble seal
End Cap
x2
Bottom Rail Holder
x2
Fixing Kit
L
LRR
Washer A Washer B
Bolt
x1x1
1
2
3
4
5
6
7
8
9
10
11
12
14
15
16
17
18
13
Screw M6x12
x2 x1
19
No. Descrip�on Qty No. Descrip�on Qty
1 Wall Profile 1 11 Arm Rail 1
2
Wall Plug
3
12
Glass
1
3
Bolt
2
13
Fixing Screw M6x12
1
4
Fixing Screw ST 4x30
3
14
Cover Cap(For Rail Holder)
1
5
Cover Cap
3
15
Rail Holder Fixing
1
6
Fixing Screw ST 4x10
3
16
Washers
2
7
Cover Cup
3
17
Bo
�
om
Rail
Holder
2(L/R)
8
Washer A
1
18
End Cap
2(L/R)
9
Washer B
1
19
Bo
�
om Seal
1
10 Bubble Seal(For Arm Rail) 1 20

B
C
Ф6 drill bit
Step 1: Position the wall profile (No 1 ) onto the bath , approximately 12-15mm from the outside bath edge , ensuring that
the side with the pre-drilled holes are facing outwards from the bath ( Diagram A).
Step 2: Level the profile with a spirit level, then mark the position using a pencil through the 3 pre-drilled screw holes in the
wall profile,drill the marked points using a 6mm masonry drill bit. Once this is done insert 3 wall plugs(No.2) (Diagram B).
NOTE :You may find it easier to mark and drill the wall if you apply masking tape to it first.
Step 3: Secure the wall profile using 3 x ST4X30 screws (No.4) (Diagram C).
12-15mm
from bath
edge
4x30mm screws
A
D
G
F
E

I
H
Step 4 : Inset the bubble seal(No.10) onto the arm rail profile(No.11). (Diagram D)
Step 5 : Drop a little bit of silicone sealant into the arm rail profile (No.11) then press the CORRECT handed end cap
(No.18) into the arm rail profile(No.11) (Diagram E)
Step 6 : Fit the washers(No.8,No.9 ) onto the arm rail profile(No.11) (Diagram F).
Step 7 : Fit the assembled arm rail above onto the wall profile then insert the bolt (No.3) to secure the arm rail profile.
Step 8 : Push the bath screen assembly onto the wall profile (Diagram H).
Step 9 : Drill 3 equally spaced holes with a 3mm drill bit through the wall profile into the frame(Diagram I)
Step 10 : Fix the bath screen assembly to the wall profile using the screws ST4 x10 (No.6). (Diagram J)
Step 11: Press the cover cap(No.7) into the hole at the top of the wall profile(Diagram K)
Left Handed
Note:Follow the steps below to assemble the bathscreen into a right hand version. The bathscreen is pre-assembled
in left hand format”. Loosen the bottom rail holder piece from the bath screen assembly ( Diagram L ) and attach the
right handed bottom rail holder ( Diagram M ).
K
Ф3 drill bit
4x10mm screws
J
left right
L M
(Diagram G).

24 HRS
DO NOT USE THE
ENCLOSURE FOR
24 HOURS AFTER
SEALING
M N
To open the bath screen please follow the steps as below:
Press the bottom rail profile with a soft downwards motion to release it from the rail holder.(Diafram O）
Lift the bottom rail to rotate it into the wall profile channel(Diagram P), then you can open/close the bath
screen.
P
O
Step 12:
Silicone the outside of the wall post as shown(M).
Step 13:
Silicone the inside of the wall post as shown(N).
Step 1
Press the bottom seal onto the bath screen as shown(M).
4:

o
Riverside Business Park,Royd Ings Avenue,Keighley, West Yorkshire,BD21 4AF
01535 613830 Technical:01535 613830 Fax: [phone]