Aquadart venturi 8 AQ6002 User manual

www.aprilproducts.co.uk
www.aprilproducts.co.uk
INSTALLATION INSTRUCTIONS
Tools Required
IMPORTANT
USE SAFETY EYE-WEAR WHEN DRILLING
6
PH2 TYPE
2.75
Hinged Bath Screen
www.aquadart.co.uk
Item Number:AQ6002
This product should be installed by a suitably qualified and proficient person. The fitting instructions should be
followed carefully to ensure a proper and safe installation. Failure to follow these instructions could result in future
injury.
These instructions and list of parts assume that installation is done against solid/tiled walls.
Please check this product for damage prior to starting the installation. No claims can be made after the product has
been fitted.
PLEASE NOTE :The minimum and maximum adjustment sizes noted on the product brochures are based on
perfectly plumb walls and trays.

1
2
8
11
12
10
9
7
6
5
4
3
13
15
14
16
1
1
2
1
2
3
4
5
6
7
8
1
3
3
1
1
Wall profile
Moving Panel
False Hinge
Middle Hinge
Bottom Strip A
Bottom Strip B
Vertical Seal A
SN Description Qty
9
10
11
12
13
14
15
1(set)
1
1
5
Wall Plug
Support Arm
Bottom Seal
Vertical Seal B(3 strips)
End Cap A (L&R)
Top Cap
Screw ST4 X 30
2
2
5
End Cap B (L&R)
16 1
Fixed Panel
17
Grub Screw M8 x6
17 2
IMPORTANT - Missing Components
Please check this product for missing components prior to installation.
For spare parts visit www.aquadart.co.uk
FIXING KIT
False hinge x2
Middle hinge x2
Wall profile top cap x1 End cap A x2 End cap B x2
Wall plug x5 Screw ST 4x30 x5
COMPONENTS AND BOX CONTENTS

A
Step 1: Position the wall profile (1) onto the bath, approximately 12-15mm from the outside bath edge. Level the
profile with a spirit level, then mark the position through the 3 pre-drilled screw holes in the wall profile
using a pencil.(A)
Step 2:Drill the marked points using a 6mm masonry drill bit ,once this is done insert 3 wall plugs (14) into the wall
holes then secure the wall profile using 3 x ST4X30 screws (15)(B).
NOTE :You may find it easier to mark and drill the wall if you apply masking tape to it first.
Step 3: Carefully insert the fixed panel(2) into the wall profile(1),it allows 0-10mm for the adjustment in case the wall
is not fully level(C)
Step 4 :Secure the false hinge(4) onto the fixed panel (D)
Step 5 :Position the bottom strip A(6) onto the bath then mark a line onto the profile, cut the profile through marked
line to get required length(E).
Step 6 :Drop the silicone sealant into the groove of the bottom strip A then reposition it onto the bath,carefully insert
the fixed panel into bottom strip A and push it into the the wall profile.(F)
12-15mm
E
B
Ф 6 drill bit
C
D
0-10mm
F

G
INSIDE
H
I
L
M
N
K
OJ
O
K
L M
J
N
I-details
I

Step 7: press the vertical seal B(9)(3 strips) into the wall profile to secure the fixed panel(2)(G).
Step 8: Fit the middle hinge(5) onto the fixed panel(2)(H)
Step 9: Push the bottom seal (10) onto the bottom of the door panel(3) then carefully lift it onto the bath to secure it
onto the fixed panel(2)(I)
Step 10:Fix the support arm onto the fixed panel(J,K)
Step 11:Drop the silicone sealant onto the bottom corner of the bottom strip A(6) and platform of the end cap A(11),
then push the correct hand of the end cap A(11) onto the bottom strip A(6), drop the silicone sealant onto
the bottom groove of the bottom stripB(7) then insert it into the end cap A(11)(L).
Step 12:Push the correct hand end cap B(12) onto the bottom strip B(7)(M).
Step 13:Press the vertical seal A (8) onto the fixed panel(2)(N).
Step 14: Push the wall profile top cap(3) onto the wall profile(1)(O)
24 HRS
DO NOT USE THE
ENCLOSURE FOR
24 HOURS AFTER
SEALING
Applying Silicone Sealant
Sealing Inside
Seal from the top of the wall profile to the bottom on the INSIDE
between the wall profile and the wall.
IMPORTANT: Do not apply sealant on inside of the tray.
Sealing Outside
Seal from the top of the wall profile to the bottom between the
wall profile and tiles on both sides. Also seal along the bottom
where the frame meets the tray. Seal the joints between the
bottom profile and any upright profiles.

o
Riverside Business Park,Royd Ings Avenue,Keighley, West Yorkshire,BD21 4AF
01535 613830 Technical:01535 613830 Fax: [phone]