THE SHOWER LAB VIEW 30 User manual

05/2021 V 1.0
VIEW 30 Illustration - View 30
Right Hand

05/2021 V 1.0
VIEW 30
IMPORTANT
•This shower screen / enclosure must be installed by suitably qualified individuals. We
recommend a minimum of two people for safe assembly of certain sections of this screen.
•Ensure all appropriate safety equipment, especially protective footwear, safety glasses
and gloves are used.
•When drilling holes in ceramic tiles, use masking tape to prevent the drill from slipping:
DO NOT use hammer action as this will crack the tiles. Use a high quality drill bit to ensure
a clean, precise hole.
Tighten hinges and brackets to the recommended 15.6N.
•
•
Please leave these instructions with the customer following installation.
PRIOR TO INSTALLATION
•Before disposing of the packaging and prior to commencing assembly, please check all
the components to ensure that they have been supplied correctly and are undamaged.
Subsequent claims for missing or damaged pieces will not be accepted once the
packaging has been disposed of and installation commenced.
•In the event of any queries please contact your supplier quoting the relevant model
information.
•The Tray / Tiled floor on which this screen is to be installed must be level on all sides.
•It may be necessary to use alternate fixings to those supplied, depending on the properties
of the walls to be fixed to.
•Use the protective corners supplied at all times until the glass is moved to its final position.
•Ensure that the glass is installed correctly, taking care to avoid installing the glass upside
down. On certain panels an easy clean coating is applied to one side only, this is clearly
marked with a sticker on the non-coated side. The coated surface is to be fitted inwards
towards the inside (wet side) of the screen.
•Ensure that all surfaces to be sealed are clean and dry prior to applying the silicone
sealant. Use a high grade fungal resistant sealant.
•Allow a minimum of 24 hours after application of the silicone sealant prior to using the
screen.
TOOLS & MATERIALS REQUIRED
Junior Hacksaw
Straight Edge (Steel
Rule)
Fine Tooth File
Set or Roofing
Square
Masking Tape
Modelling Knife
Spirit Level
Pencil
Silicone Gun
Power Drill
Ø6mm Masonry Drill Bit
2x Suction Glass Lifters
High Quality Silicone Sealant
Tape Measure
Pozi-drive
Screwdrivers, PZ1&2
Safety Glasses and
Gloves
CARE AND MAINTENANCE
(please ensure that these instructions are left with the installed unit)
•We recommend routine cleaning of your screen / enclosure with hot water using a soft
cloth, then drying with a dry soft cloth or chamois leather.
Ritec Aftercare for Shower Glass is recomended for best results.
•All glass has been treated with EASY CLEAN glass finish and care must be taken to avoid
any abrasive cleaning products that may damage the special surface protection.
•DO NOT use acidic based de-scaler products or products containing bleaches or solvents.
Digital Torque Wrench

05/2021 V 1.0
VIEW 30
Spacers Wall Prole End Cap
x1
Supplied Parts
Inline Panel
x1
Door
x1
Slider Bracket Template
x1
Nylon Block
x1
Pig Nose Adapter
x1
Packers

05/2021 V 1.0
VIEW 30
Supplied Parts
Underframe Wedge Gasket
x2
Underframe
x1
Underframe Gasket
x1
Wall Prole
x1
Wall Prole Soft Seal
x1
Wall Prole Rigid Seal
x1
Underframe Top
x1
Glass to Wall Seal
x1
Glass to Glass Slider Seal
x1

05/2021 V 1.0
VIEW 30
Slider Door Roller
x2
Slider Panel Fixing
x2
Slider Door Retainer
x2
Slider Door Stop
x1
Slider Wall Bracket
x2
Bottom Door Guide
x1
Supplied Parts
Slider Bar
x1
Slider Bar Insert
x1

05/2021 V 1.0
VIEW 30
These instructions are for the View 30.
The following instructions are valid for both the 20mm and 30mm proles. The 30mm prole is
used in the following instructions.
Please use the below diagram to reference the list of parts.
A
B
I
C
H
D
F
E
G
Door Panel
Inline Fixed Panel
Wall Prole
Wall Prole Soft Seal
Wall Prole Rigid Seal
Underframe Wedge Gasket
Underframe
Underframe Gasket
JUnderframe Top
Wall Prole End Cap
N
M
K
L
Bottom Door Guide
Glass to Wall Bubble Seal
Glass to Glass Slider Seal
Slider Bar
OSlider Bar Insert
PSlider Door Stop
QSlider Wall Bracket
RSlider Door Roller
SSlider Door Retainer
TSlider Panel Fixing
O
R
B
D
E
C
I
K
J
F
L
A
G
H
M
PT
N
S
Q

05/2021 V 1.0
VIEW 30
    
    
    
    
    
    
    
ADJUSTMENT SHEET
STANDARD ENCLOSURES
Please Note
Only Standard Enclosures are shown above. If you have a Bespoke Enclosure, reference the delivery
note for the panel specificaons of the Enclosure.
BESPOKE ENCLOSURES
LH RH

05/2021 V 1.0
VIEW 30
01/13
Ensure the base is level.
Measure the width of the opening
where the door is to be fied.
Mark this measurement on the
Underframe boom.
It is recommended to use masking tape
on the Underframe to mark your
measurement.
Cut squarely using a chop saw.
Use a fine toothed file to remove any
burrs, be careful not to damage the
surface finish.
Posion the Underframe parallel to
tray edge.
If using a raised shower tray, leave a
minimum 3mm gap from the edge of
the tray (5mm is recommended). This is
the lip distance.
DO NOT fix the Underframe channel to
the tray at this stage.
Slide the Boom Door Guide Fixing
Plate into the T Slot of the Underframe.
3mm minimum
Shower Tray
X
01 02
03 04

05/2021 V 1.0
VIEW 30
02/13
Fix the Underframe into the correct
posion. Peel off the backing strips
from the self adhesive tape and push
firmly into posion.
Place the Underframe Gasket into the
Underframe and bu up against the
wall.
Place the Wall Profile over the
Underframe and up against the wall.
Ensure the Wall Profile is vercal by
using a spirit level. Mark the posions
of the pre-drilled holes.
05 06
07 08

05/2021 V 1.0
VIEW 30
03/13
Remove the Wall Profile and drill holes
with a 6mm high quality drill bit for a
clean and precise hole.
Fully insert the wall plugs.
Pre drill the screws in to the Wall
Profile to create the thread to ease
later steps.
Remove screws aer drilling.
Fix the Wall Profile in place.
Take the Wall Profile So Seal and push
the seal into place on the vercal Wall
Profile to cover the screws.
Ensure the fin is on the inside (wet
side).
Use the Nylon Block to help.
Using purpose built "Glass Liers",
posion and sit the Inline Glass Panel
on to the Underframe Gasket and push
against the Wall Profile.
Note the orientaon and posion of
the Panel, this can be determined by
any holes or aached labels.
Wet Side
Professional Tip
If drilling ceramic tiles, place
masking tape on the tiles before
marking and drill through the
tape to prevent the drill bit from
skidding.
DO NOT use Hammer Action as
this will break the tiles.
09 10
11 12

05/2021 V 1.0
VIEW 30
04/13
Remove and replace the Panel adding
or subtracng spacers as necessary to
level the Panel (to a maximum height
of 5mm inside the Underframe).
Check the Panel is level using a Spirit
Level.
If the Wall Profile is flush with the
Inline Glass Panel, move on to step 17.
If the end of the Wall Profile is not flush
with the top of the Inline Glass Panel,
mark the Wall Profile. Using a straight
edge, mark where the wall channel
needs to be trimmed.
To protect the channel finish, it is
recommended to mark on masking
tape.
Remove the Inline Panel, Wall Profile
So Seal, and the Wall Profile.
Trim the Wall Profile.
Use a fine file to remove any burrs. Be
careful not to damage the channel
finish.
Re drill the screws in to the Wall Profile
and remove aer drilling.
Reinstall the Wall Profile, Wall Profile
So Seal, and Glass Inline Panel.
WARNING
The glass is heavy and may
damage the oor or underframe if
handled incorrectly. It is advisable
to use a suitable non-slip
protective mat or piece of carpet.
Never rest the glass across the
underframe as this may cause
damage.
13 14
15 16

05/2021 V 1.0
VIEW 30
05/13
Measure and check the distance from
the Inline Panel to the opposite wall
ling at the boom and at the top are
equal.
To centre the panel, add 1mm Packers
on both sides of Inline Panel in the
Underframe.
Ensure there is adequate glass in the
Wall Profile. (6mm is recommended)
Apply Rigid Seal to dry side of the Wall
Profile starng from the archway of the
Wall Profile up to the top face of the
Wall Profile.
Gently tap the Wall Profile Rigid Seal
into place using a rubber mallet with
the Nylon Block to protect the Glass
and the Wall Profile.
=
=
6mm min
Wall ProleGlass Panel
Flush
Rigid Seal
Glass Panel
17 18
19 20

05/2021 V 1.0
VIEW 30
06/13
Remove Packers and feed the
Underframe Wedge Gasket into the
archway gap of the Fixed Panel and
trace along the Glass on both sides.
Spray water on Glass Panel and use
Nylon Block to help feed Gasket.
Mark the Wedge Gaskets at the edge of
the Inline Panel.
Remove both Wedge Gaskets and trim.
Reinstall both Wedge Gaskets aer
trimming.
Trim both of the Wall Profile seals at
the top face of the Wall Profile using a
blade.
Measure the distance from the wall to
the nearest fixing hole on the Inline
Panel. Ensure this measurement is truly
horizontal.
Subtract 15mm to get your final
dimension.
x - 15mm
21 22
23 24

05/2021 V 1.0
VIEW 30
Fixing Holes
07/13
Mark the final dimension on the Slider
Bar on the fixing hole side.
Cut squarely using a chop saw and
finish the edge.
Use the Slider Rail Bracket Template to
mark the hole posions for the Slider
Rail Bracket on the Wall Profile side of
the enclosure.
Using a Ø6mm high quality drill bit for
a clean and precise hole, drill all holes
and fully insert the wall plugs.
Fix the Slider Wall Bracket in place
using the supplied screws.
Trace the Wall Profile on the door side
wall. Use the Spirit Level against the
Inline Panel to accurately trace the
Profile.
Align the Slider Rail Bracket Template
to the sketch and mark the holes.
Professional Tip
If drilling ceramic tiles, place
masking tape on the tiles before
marking and drill through the
tape to prevent the drill bit from
skidding.
DO NOT use Hammer Action as
this will break the tiles.
x - 15mm
25 26
27 28

05/2021 V 1.0
VIEW 30
Fixing Holes
x
x - 30mm
Slider Bar Insert
08/13
Using a Ø6mm high quality drill bit for
a clean and precise hole, drill all holes
and fully insert the wall plugs.
Fix the Slider Wall Bracket in place
using the supplied screws.
Measure the wall to wall distance.
Ensure this measurement is truly
horizontal.
Subtract 30mm to get your final
dimension.
Mark the final dimension on the Slider
Bar on the opposite side of the Slider
Bar.
Cut squarely using a chop saw and
finish the edge.
Insert the Slider Bar Insert into the
Slider Bar and ensure that the threaded
holes in the Slider Bar Insert align with
the clearance holes on the Slider Bar.
Professional Tip
If drilling ceramic tiles, place
masking tape on the tiles before
marking and drill through the
tape to prevent the drill bit from
skidding.
DO NOT use Hammer Action as
this will break the tiles.
29 30
31 32

05/2021 V 1.0
VIEW 30
Door Stop
09/13
Put the Glass Protectors on the boom
two corners of the Door Panel.
Using purpose built “Glass Liers”,
posion the Door Panel inside the
Enclosure and securely rest the Panel
against the back wall.
Slide the Collar over the Wall Bracket
and fix in place using the supplied Grub
Screws.
Ensure the Door Stop is posioned and
orientated as shown. This will be
adjusted in a later step.
Fix the Inline Panel to the Slider Bar by
using the supplied Door Retainers.
Use the supplied Pig Nose Adapter to
fix in place.
Fix the Boom Door Guide to the
Underframe by fixing the supplied
screws into the Boom Door Guide
Plate.
Ensure that the Boom Door Guide
bus up against the Inline Panel.
33 34
35 36

05/2021 V 1.0
VIEW 30
10/13
Use the Pig Nose Adapter to fix the Top
Rail Guides on to the Door.
Using purpose built “Glass Liers”,
carefully posion the Door Panel on
the Slider.
Ensure that the Door is level by
adjusng the eccentric runners.
Use two allen keys and the supplied Pig
Nose Adapter to adjust.
Use the supplied Pig Nose Adapter to
fix Boom Door Rail in place.
Fix the Boom Door Guide bracket in
place using the supplied Grub Screws.
Ensure that the Boom Door Guide
Bracket is lightly touching the Door
before fixing in place.
37 38
39 40

05/2021 V 1.0
VIEW 30
Outside of
enclosure
x
Door Stop
11/13
Adjust the Door Stop to ensure that the
Door does not travel too far. Pay
parcular aenon to the Handle (if
supplied) to ensure that it does not
clash with the Fixed Inline Panel.
Fix in place by ghtening the Grub
Screws located on top of the Door Stop.
Measure the distance between the wall
and the edge of the Boom Door
Guide.
Mark and cut the Underframe Top.
Snap the Underframe Top on to the
Underframe.
Aach the Glass to Wall Bubble Seal to
the Door.
Leave the Seal oversized. This will be
trimmed later.
41 42
43 44

05/2021 V 1.0
VIEW 30
12/13
Push both Vercal Seals down as far as
they can go. With a straight edge, mark
where the Seals will be trimmed.
Mark the Glass to Glass Slider Seal just
below the Slider Bar.
Remove the Seals and trim with a fine
toothed hacksaw.
Replace the Seals.
Push both Vercal Seals down as far as
they can go. With a straight edge, mark
where the Seals will be trimmed.
Mark the Glass to Glass Slider Seal just
below the Slider Bar.
Remove the Seals and trim with a fine
toothed hacksaw.
Replace the Seals.
Underframe
Wall Channel
Silicone
Apply the Wall Profile End Cap to the
top of the Wall Profile and fix in place
using self tapping screws.
Apply silicone sealant along the wall
and floor all around the outside of the
Underframe and Wall Profiles.
45 46
47 48

05/2021 V 1.0
VIEW 30
13/13
Apply silicone to the edges of the
Underframe Top where it meets the
Glass Inline Panel and the wall.
Check silicone has been applied to all
the below outside areas.
Silicone
Silicone
Check silicone has been applied to all
the below inside areas.
Let the silicone sealant cure for 24
hours.
Silicone
49 50
51