Arbor Technology ITX-i89H0 User manual

I
ITX-i89H0
User’s Manual
Version 1.0
Mini-ITX Industrial Motherboard
2016.05

- II -
This page is intentionally left blank.

- i -
Revision History
Version Release Time Description
1.0 May, 2016 Initial release

- ii -
Contents
Table of Contents
Revision History .................................................................................i
Table of Contents ..............................................................................ii
Preface...............................................................................................iv
Copyright Notice .................................................................................... iv
Declaration of Conformity ...................................................................... iv
CE................................................................................................... iv
FCC Class A .................................................................................... v
RoHS ............................................................................................... v
SVHC / REACH .............................................................................. vi
Warning.................................................................................................. vi
Replacing Lithium Battery ...................................................................... vi
Technical Support .................................................................................. vi
Warranty.................................................................................................vii
Chapter 1 - Introduction....................................................................1
1.1. Product Highlights............................................................................2
1.2. About this Manual ............................................................................2
1.3. Specications...................................................................................3
1.4. Inside the Package ..........................................................................4
1.5. Ordering Information ........................................................................4
1.6. RAM Installation...............................................................................5
Chapter 2 - Getting Started...............................................................7
2.1. Board Dimensions............................................................................8
2.2. Block Diagram..................................................................................9
2.3. Jumpers & Connectors ..................................................................10
2.3.1. Layout .................................................................................. 10
2.3.2. Jumpers ............................................................................... 11
2.3.3. Connectors .......................................................................... 15
2.4. Driver Installation Notes.................................................................32
Chapter 3 - BIOS..............................................................................33
3.1. Main ...............................................................................................35
3.2. Advanced .......................................................................................36
3.2.1. CPU Conguration...............................................................37
3.2.2. PCI Subsystem Settings......................................................38
3.2.3. SATA Conguration.............................................................. 39
3.2.4. ACPI Settings.......................................................................40
3.2.5. USB Conguration ...............................................................41
3.2.6. AMT Conguration ...............................................................42
3.2.7. Super IO Conguration ........................................................43
3.2.8. Hardware Monitor ................................................................44

- iii -
Contents
3.2.9. S5 RTC Wake Settings ........................................................45
3.2.10. CSM Conguration ...........................................................46
3.3. Chipset...........................................................................................47
3.3.1. Graphics Conguration ........................................................48
3.3.2. PEG Port Conguration .......................................................48
3.3.3 Memory Conguration .........................................................49
3.3.4. LCD Control .........................................................................49
3.3.5 PCI Express Conguration ...................................................50
3.3.6 USB Conguration ................................................................50
3.3.7 HD Audio Conguration ........................................................50
3.3.8 PCH LAN Conguration........................................................51
3.4. Security .......................................................................................... 52
3.5. Boot................................................................................................53
Appendices ......................................................................................55
Appendix A. I/O Port Address Map ......................................................56
Appendix B. Interrupt Request Lines (IRQ) ..........................................58
Appendix C. BIOS Memory Map...........................................................59
Appendix D: Watchdog Timer (WDT) Setting.......................................60

- iv -
Preface
Preface
Copyright Notice
All Rights Reserved.
The information in this document is subject to change without prior notice in
order to improve the reliability, design and function. It does not represent a
commitment on the part of the manufacturer.
Under no circumstances will the manufacturer be liable for any direct, indirect,
special, incidental, or consequential damages arising from the use or inability
to use the product or documentation, even if advised of the possibility of such
damages.
This document contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic, or other means in any form without prior written permission of the
manufacturer.
Declaration of Conformity
CE
The CE symbol on your product indicates that it is in compliance with the
directives of the Union European (EU). A Certicate of Compliance is available
by contacting Technical Support.
This product has passed the CE test for environmental specications when
shielded cables are used for external wiring. We recommend the use of shielded
cables. This kind of cable is available from ARBOR. Please contact your local
supplier for ordering information.
This product has passed the CE test for environmental specications. Test
conditions for passing included the equipment being operated within an
industrial enclosure. In order to protect the product from being damaged by ESD
(Electrostatic Discharge) and EMI leakage, we strongly recommend the use of
CE-compliant industrial enclosure products.
Warning
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

- v -
Preface
FCC Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
RoHS
ARBOR Technology Corp. certies that all components in its products are
in compliance and conform to the European Union’s Restriction of Use of
Hazardous Substances in Electrical and Electronic Equipment (RoHS) Directive
2002/95/EC.
The above mentioned directive was published on 2/13/2003. The main purpose
of the directive is to prohibit the use of lead, mercury, cadmium, hexavalent
chromium, polybrominated biphenyls (PBB), and polybrominated diphenyl
ethers (PBDE) in electrical and electronic products. Member states of the EU
are to enforce by 7/1/2006.
ARBOR Technology Corp. hereby states that the listed products do not contain
unintentional additions of lead, mercury, hex chrome, PBB or PBDB that exceed
a maximum concentration value of 0.1% by weight or for cadmium exceed
0.01% by weight, per homogenous material. Homogenous material is dened as
a substance or mixture of substances with uniform composition (such as solders,
resins, plating, etc.). Lead-free solder is used for all terminations (Sn(96-96.5%),
Ag(3.0-3.5%) and Cu(0.5%)).

- vi -
Preface
SVHC / REACH
To minimize the environmental impact and take more responsibility to the earth
we live, Arbor hereby conrms all products comply with the restriction of SVHC
(Substances of Very High Concern) in (EC) 1907/2006 (REACH --Registration,
Evaluation, Authorization, and Restriction of Chemicals) regulated by the
European Union.
All substances listed in SVHC < 0.1 % by weight (1000 ppm)
Warning
Single Board Computers and their components contain very delicate
Integrated Circuits (IC). To protect the Single Board Computer and its
components against damage from static electricity, you should always follow the
following precautions when handling it :
1. Disconnect your Single Board Computer from the power source when you
want to work on the inside.
2. Hold the board by the edges and try not to touch the IC chips, leads or
circuitry.
3. Use a grounded wrist strap when handling computer components.
4. Place components on a grounded antistatic pad or on the bag that comes
with the Single Board Computer, whenever components are separated from
the system.
Replacing Lithium Battery
Incorrect replacement of the lithium battery may lead to a risk of explosion.
The lithium battery must be replaced with an identical battery or a battery type
recommended by the manufacturer.
Do not throw lithium batteries into the trash-can. It must be disposed of in
accordance with local regulations concerning special waste.
Technical Support
If you have any technical difculties, please do not hesitate to call or e-mail our
customer service.
http://www.arbor-technology.com/
E-mail:[e-mail]

- vii -
Preface
Warranty
This product is warranted to be in good working order for a period of two years
from the date of purchase. Should this product fail to be in good working order
at any time during this period, we will, at our option, replace or repair it at no
additional charge except as set forth in the following terms. This warranty does
not apply to products damaged by misuse, modications, accident or disaster.
Vendor assumes no liability for any damages, lost prots, lost savings or any
other incidental or consequential damage resulting from the use, misuse of, or
inability to use this product. Vendor will not be liable for any claim made by any
other related party.
Vendors disclaim all other warranties, either expressed or implied, including but
not limited to implied warranties of merchantability and tness for a
particular purpose, with respect to the hardware, the accompanying product’s
manual(s) and written materials, and any accompanying hardware. This limited
warranty gives you specic legal rights.
Return authorization must be obtained from the vendor before returned
merchandise will be accepted. Authorization can be obtained by calling or
faxing the vendor and requesting a Return Merchandise Authorization (RMA)
number. Returned goods should always be accompanied by a clear problem
description.

This page is intentionally left blank.

- 1 -
1Chapter 1
Introduction
Chapter 1 - Introduction

- 2 -
Introduction
1.1. Product Highlights
• Soldered onboard 6th Generation Intel®
Core™/Xeon® Processor
• Integrated Gigabit Ethernet
• ECC memory support
• Dual DisplayPorts and one HDMI support
• Extended operating temp: -20~70ºC
1.2. About this Manual
This manual is intended for experienced users and integrators with hardware
knowledge of computers. If you are not sure about the description in this manual,
consult your vendor before further handling.
We recommend that you keep one copy of this manual for the quick reference
for any necessary maintenance in the future. Thank you for choosing ARBOR
products.

- 3 -
Introduction
1.3. Specications
Form Factor Mini-ITX industrial motherboard
Processor
Soldered onboard Intel®Core™ i3-6100E Dual-core 2.7GHz (Base)
Intel®Xeon®Processor E3-1505L V5 Quad-core 2.0GHz (Base) / 2.8GHz
(Trubo)
Intel®Xeon®Processor E3-1515M V5 Quad-core 2.8GHz (Base) / 3.7GHz
(Trubo)(Optional)
Chipset Intel®CM236
Memory 2 x DDR4 SO-DIMM sockets W/ECC, supporting up to 32GB SDRAM
BIOS AMI BIOS
Super I/O Nuvoton NCT6776D
Serial Port 1 x UART Connector
Keyboard & Mouse USB interface Keyboard/ Mouse
USB 2.0 4 x USB 2.0 ports
USB 3.0/2.0 6 x USB 3.0/2.0 ports
Expansion
1 x PCIe x16 Gen 3.0 slot
1 x NGFF M.2 E-Key socket for Wireless
1 x LPC interface
Storage 2 x Serial ATA ports with 600MB/s HDD transfer rate
1 x NGFF M.2 M-Key socket for SSD
Ethernet Chipset 1 x Intel®i219LM GbE PHY
Audio Interface Realtek®ALC662 5.1 Channel HD Audio CODEC, Mic-in/Line-out
Graphic Chipset Integrated Intel®HD Graphics
Graphic Interface 1 x HDMI port
2 x DisplayPort ports
OS Support Windows 8.1 64-bit
Windows 10 64-bit
Power Input DC 12V DC jack
Power Consumption 4.17A@12V (w/ E3-1505L)
Operating Temp. -20 ~ 70ºC (-4 ~ 158ºF)
Operating Humidity 10 ~ 95% @ 70ºC (non-condensing)
Dimension (L x W) 170 x 170 mm (6.7” x 6.7”)

- 4 -
Introduction
1.4. Inside the Package
Before starting to install the single board, make sure the following items are
shipped:
1 x ITX-i89H0 Mini-ITX industrial motherboard
1 x Cooler
1 x Driver CD
1 x Quick Installation Guide
If any of the aforelisted items is damaged or missing, contact your vendor
immediately.
1.5. Ordering Information
ITX-i89H0-A-6100E Intel®Core™ Processor i3-6100E/CM236 PCH Mini-
ITX motherboard
ITX-i89H0 (BTO) Intel®Xeon®Processor E3-1505L/CM236 PCH Mini-
ITX motherboard
CBK-06-89H0
2 x SATA cables
1 x SATA Power cable
1 x COM cable
1 x USB cable
1 x USB 3.0 cable

- 5 -
Introduction
1.6. RAM Installation
The main board has one memory module (SO-DIMM) sockets. Load the
computer with a memory module of higher capacity to make programs run faster.
The memory module for the computer’s SO-DIMM socket should be a DDR3L
with a “key notch” off the centre among the pins, which enables the memory
module for particular applications. There are another two notches at each left
and right side of the memory module to help x the module in the socket.
key notch
side notch
side notch
To install the memory module:
1. Find the SO-DIMM socket on the board as marked in the illustration below.
The SO-DIMM socket is horizontal type, and it has two spring-loaded locks
to x the memory module.
2. Confront the memory module’s edge connector with the SO-DIMM slot
connector. Align the memory module’s key notch at the break on the SO-
DIMM slot connector.
3. Fully plug the memory module until it gets auto-locked in place.
To uninstall the memory module:
1. Pull back the locks from both sides of the SO-DIMM socket.
The memory module will be auto-released from the socket.
2. Remove the memory module.

- 6 -
This page is intentionally left blank.

- 7 -
2Chapter 2
Getting
Started
Chapter 2 - Getting Started

- 8 -
Getting Started
2.1. Board Dimensions
156.5
135.65
111.76
85.8
57.9
33.1
170
Unit: mm
163.65
6.17
10.16
Ø3.96x4PCS
33.02
170
165.1

- 9 -
Getting Started
2.2. Block Diagram
DMI
(x4)
DDI-1
Intel®
SKYLAKE
BGA
Processor
Intel®
SPT-H
PCH
DDI-2
DDI-3
USB 2
2x10-pin 2.00mm
pitch pin header
LAN1
RJ-45 connector
2 x USB 2.0
(Type A)
USB 1
Type A conn.
2 x USB 2.0 ports USB 3
2x5-pin 2.54mm
pitch pin header
2 x USB 3.0/2.0 port
4 x USB 3.0/2.0 port
2 x USB 2.0 ports
HD Link HD CODEC
ALC662
Mic-in/Line-out AUDIO1
2x3.5mm phone
jack stacked
Line-out/Mic-in
DCIN1
+12 DC Brick
DDR4 - 2133MHz
2 x DDR4
SO-DIMM socket
PCIe Gen3 x 16
x16PCEG1
WIFI1
E-key Socket
USB 2.0 port
PCIe Gen3 x 1
PCIe Gen3 x 1 GbE
Intel i219LM
LAN controller
SSD1
M-key Socket
SATA0
PCIe
SATA1,2
SATA connector SATA4,5
JCOM1
2x5-pin 2.54mm
pitch pin header
NCT6776D
LPC
Flash
Flash
LPC1
2x10-pin 2.54mm
pitch female
pin header
LPC
HDMI1
HDMI conn.
DP1
Double Stacked
DP Connector
SPI

- 10 -
Getting Started
2.3. Jumpers & Connectors
The board comes with some connectors to join some devices and also some
jumpers to alter the hardware conguration. The following in this chapter will
explicate each of these components one-by-one.
2.3.1. Layout
This section will provide an overview of this board.
JME1
➋
JME2
➌
➊JPCH1
JLCD1
➍
⑰JCOM1
⑩CPUFAN1
⑪X16PCEG1
①USB2
④AUDIO1
⑤USB1
⑥LAN1 ⑦HDMI1 ⑧DP1
②SATA1
③SATA2
⑨DCIN1
⑫FP1
⑬SYSFAN1
⑭PWROUT1
⑲SSD1
⑯LPC1 ⑮USB3
⑱WIFI1