Argos 2 Door Media Unit/Low Sideboard 482/0437 User manual

Assembly Instructions - Please keep for future reference
Width - 117.2cm
2 Door Media Unit/Low Sideboard
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 01709 534123
Please turn to back page for important information when contacting Customer Helpline.
Dimensions
Depth - 38.8cm
Height - 57.6cm
Rev A - 30/09 /15
033 xx 6003
MADE IN
GREAT BRITAIN
482/0437

Important - Please read these instructions fully before starting assembly
Safety and Care Advice
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and seperate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Parts of the assembly will be
easier with 2 people.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Care and maintenance
Always lift furniture when
moving it (do not drag)
otherwise the joints may be
damaged.
From time to time check that
there are no loose screws on
this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
1
Dust surfaces with a soft, dry,
lint free cloth.
More stubborn marks can be
removed using a damp
(not wet) cloth. Wipe the
surface dry immediately
using a soft lint free cloth.
Do not use detergents, abrasive
cleaning products or cleaning
products that contain ammonia,
solvents or silicone as these
may damage the surface finish.
To protect the furniture,
position the furniture out of
direct sunlight and away from
direct heat sources such as
radiators and fires.
Do not place the furniture in
excessively dry and humid
conditions.
Do not place hot or cold
objects on the surface, always
use protective mats to avoid
marking the furniture.
Clean spills up immediately
Dispose of all packaging
carefully and responsibly
when assembly complete.
Do Not dispose of packaging
until assembly complete.

Please check you have all the panels listed below
Components -Panels
2
Important - Thick lines indicate finished edges
Bottom
(101.2x34.0cm)
9886
Left End
(50.8x38.2cm)
9887
Right End
(50.8x38.2cm)
9888
Left Divider
(41.4x34.0cm)
9890
Right Divider
(41.4x34.0cm)
9895
Door x 2
(42.4x27.8cm)
9893
Back x 2
(43.3x28.6cm)
9894
Top
(111.8x38.8cm)
9885
Small Shelf x 2
(26.7x33.8cm)
9891
Large Shelf
(44.5x33.8cm)
9892
Plinth
(101.2x7.6cm)
9889
If you have damaged or missing panels, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Trim x 2
(50.8x5.0 x1.2cm)
684xx5505

3
70 80 90 100 110 120
010 20 30 40 50 60
mm
130 140 150 160 170
Ruler - Use this ruler to help correctly identify the screws
Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly, In some case more
fittings may be supplied than are required.
Tools required
If you have damaged or missing components, call the
Customer Helpline: 01709 534123 Please turn to back page
for important information when contacting Customer Helpline.
Cross headed screwdriver
(medium & large )
Small Hammer
Tape Measure
Eye protection
(when using a
hammer)
Large cam x 16
Code 760001103
Metal dowel x 16
Code 760003004
ABC
E
DF
I
Panel pin x 20
Code 760001012
Panel pin guide x 1
Code 684004501
GH
JKL
Fully cranked 26mm
hinge x 4
Code 652001120
Hingeplate x 4
Code 653006000
Screw x 8
Code 690001008
Shelf Support x 8
Code 681003001
Bradawl
18mm bolt x 4
Code 700002021
Wooden dowel x 4
Code 770001006
45mm screw x 4
Code 690001075
Handle x 2
Code 644003511
Shelf Pin x 8
Code 760001137
M

Exploded View
4
0007
0007
0001
0002
0003
0003
0004
0004
0005
0005
9999
0006
0006
9164
684xx6531
684xx6531
9998

Step 1
Assembly Instructions
5
A
x4
A
Fitting cams to the
bottom panel.
Insert 4 metal cams
into the bottom panel
.
Note: Ensure cam arrow
points towards the edge
with the hole.
9999
A
A
x4
Step 2
Fitting cams to the
plinth panel.
Insert 4 metal cams
to the plinth panel .
9164
A
A
A
A
9164
A
B
B
B
B
B
B
B
B
Step 3x8
B
Fitting dowels to the
top panel.
B
B
Insert 8 metal dowels
into the top panel
Note: Insert metal
dowels as far as
shown by arrows. Do not
over tighten.
9998
B
9998
A
A
A
A
9999

Assembly Instructions
6
Step 4
Step 5
B
B
B
B
B
B
B
H
H
H
H
A
A
A
A
Insert 4 metal dowels ,
2 hinges and 2
cams into the left end
panel .
Repeat on the right end
panel .
Attach dowels, cams
and hinges to both of
the end panels.
B
A
H
Insert 2 cams
and 2 wooden dowels
into the divider
panel .
Repeat on remainding
divider.
Attach dowels, cams to
both divider panels.
0001
0002
0003
x8
BA
x4
A
A
x4
x4
H
J
J
x4
0001
0002
B
A
A
J
J
0003
Holes not used at
this stage.
X 2

Assembly Instructions
7
Step 6
Attach hinges and
handles to the doors
a: Insert hinges
into holes, ensure
the hinge is straight
(90 degree angle).
b: Before securing the
hinges , we recommend
you pre - mark the doors
using a bradawl.
G
c: Secure hinges to
doors using screws .
G
K
d: Secure handle to
doors using bolts
Repeat on the second
door.
E
I
G
G
x4
K
x8
E
x4
I
x2
A
B
C
D
Bradawl
90
Correct
98
Incorrect
I
0006
G
G
K
K
KK
E
E
0006
0006
0006

Assembly Instructions
8
Step 7
Step 8
Connect the top panel
to the left end panel
and the divider panels.
Connect the dowels in the
top panel to the
dowels in the left end
panel and divider
panels .
0001
0003
0003
9998
Turn cams 180 degrees to
lock.
Turn cams 180 degrees to
lock.
Edged face
0003
0003
0001
9998
Large silver ttings
visible in this face
Large silver ttings
visible in this face
IMPORTANT.
Please ensure divider
panels are
positioned as shown.
Connect the bottom
and the plinth panel to
the left end panel.
Connect the dowels in the
left end panel to
the cams in the bottom
panel and the
plinth panel .
Ensure that dowels in both
panels locate
into bottom panel
guide holes.
0001
9999
9164
Edged face
9890
0001
9999
9164
0003
0003
9999
0003
Ensure plinth sits
flush.
Ensure plinth is
not overhanging.

Assembly Instructions
9
Step 9
Step 10
Connect the right end
panel to the top,
bottom and plinth
panel.
Connect the dowels in
the top panel to
the cams in the right end
panel .
Connect the dowels in
the right end panel
to the cams in the bottom
panel and the
plinth panel .
9998
0002
0002
9999
9164
9890
9999
9164
0002
9998
Secure the bottom
panel to the divider
panels.
Using 4 screws ,
secure the bottom panel
to the divider
panels .
9999
0003
L
0003
0003
x4
L
9890
9999
L
L
L
L
Lay unit on its front to
attach the backpanels
Turn cams 180 degrees to
lock.