Argos New Sywell 282/7920 User manual

MADE IN
BRITAIN
Dimensions
New Sywell - 3+3 Drawer Chest
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 08/04/14
Important - Please read these instructions fully before starting assembly
ALR3013
282/7920
278/1406
Width - 98.5cm
Depth - 40cm
Height - 55.5cm
287/0049
275/7375
Issue 2 - 08/04/14
Increase drawer box size.
Add 12 wedges.
Add 4 plastinails.
Remove old cat codes and add new

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 28.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top (D2564A)
(953 x 394mm)
Rail (D2566A)
(953 x 78mm) x 2
Divider (D2565A)
(498 x 393mm)
Drawer Front (D2567A)
(465 x 162mm) x 6
Drawer Base (T447-367)
(447 x 367mm) x 6
Back (X979-524)
(979 x 524mm)
Drawer Back (W436-124)
(436 x 124mm) x 6
1Left Side (D2547A)
(553 x 396mm)
2Right Side (D2548A)
(553 x 396mm)
3
5
4 6
9
10
11
7 8
Left Drawer Side (W370-124LH)
(370 x 124mm) x 6
Right Drawer Side (W370-124RH)
(370 x 124mm) x 6

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 7
B
Metal dowel (F901) x 22
C
D E
G H I
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J
M
9mm Screw (F74) x 12 9mm Screw (F73) x 24
Drawer runner (F1004) x12
Electric drill
(do not use for
fitting screws)
Knock-in Peg (F171) x 24
Small locking
nut (F3) x 12
Large locking
nut (F900) x 10
K
Handle (F315) x 6
25mm Screw (F95) x 12
L
Feet (F854) x 2
Nail (F51) x 20
F
45mm Screw (F65) x 2
O
Plastic Nail (F91) x 4
N
Wedgefix (F639) x 12

6
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
x 6 x 6
x 6
B
Prepare the 6 drawer
fronts
Screw 2 metal dowels
into the holes shown on
the back of each drawer
front .
Note: Tighten the metal
dowels up fully against
the panels.
B
6
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
E
7
8
Step 2
Step 3
B
B
6
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
7
8
6
E
7
8
Note: The locking nuts can be on
either surface of the drawer sides.
Make sure that the small groove
is on the inside, as shown.
E
E
B
B
E
Small groove
EE
78
7
8
x 6

Assembly Instructions
5
Step 4
Step 5
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
10
7 8
6
x 6
Fit the drawer back
Fit the drawer back
down onto the drawer
base .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
9
10
10
9
9
C
7 8
x 6
Attach the handles
Attach a handle to
each drawer front
using 2 screws .
K
G
Step 6
6
x 6
10
8
6
7
9
C
C
C
C
Step 7
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
N
N
N
N
10 8
7
6
K
G
G
6
x 6

Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 8
Finished
front edge
I
M
Finished
front edge
I
M
Step 9
Prepare the right side
a: Place 3 runners on
the right side . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .
Screw 4 metal dowels
into the right side .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
M
2
I
B
2
M
I
2
a:
b:
a:
b:
I
M
I
M
I
M
I
I
I
B
B
B
B
1
1
I
M
I
M
I
M
B
B
B
B
Finished
front edge
Finished
front edge
2
2
Prepare the left side
a: Place 3 runners on
the left side . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .
Screw 4 metal dowels
into the left side .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
M
1
I
B
1
M
I
1
I
I
I

Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 10
Prepare the top
Tap 2 wooden dowels
into the top .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 4 large locking
nuts into the
top .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Screw 2 metal dowels
into the top .
Fit the top to the right
side
Push the top onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the top .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 11
D
10mm
A
A
4
D
4
4
2
D
4
D
D
D
D
D
A
A
Finished
front edge
4
B
B
plain
chipboard
surface
plain chipboard surface
4
2
B
D
B
4

A
Finished
front edge
Assembly Instructions
8
Step 12
a:
b:
c:
d:
D
D
I
M
I
M
I
M
Finished
front edge
I
M
Prepare the divider
a: Place 3 runners on
the divider . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .
Insert 2 large locking
nuts into the divider
. .
Tap a wooden dowel
into the upright .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the divider .
Turn the divider over
c: Place 3 runners on
the divider . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .
d: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the divider .
M
3
I
M
3
I
D
3
M
I
3
M
I
3
I
I
I
Finished
front edge
I
M
I
M
I
M
I
I
I
Finished
front edge
Finished
front edge
Turn the
divider over
Finished
front edge
I
M
3
3
3
3
A
3

Finished
front edge
Assembly Instructions
9
Step 13
Step 14
Prepare the 2 rails
Tap 2 wooden dowels
into each of the 2 rails .
Insert 2 large locking
nuts into each of the
2 rails .
Step 15
A
5
D
5
x 2
4
D
D
A
A
plain chipboard surface
5
Finished
front edge
3
Fit the divider
Push the divider onto
the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the divider .
3
4
D
3
Note: Support this
rail until the left
side has been fitted
in the next step.
Fit the rails
Push the 2 rails onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the rails .
5
2
D
55
5
2