Argos Jenson 876/9109 User manual

Spare Parts
Visit: www.argos-support.co.uk
Email: [email protected]
Call: 0330 016 1114
Customer Support
Call: 0345 640 2020
Issue 1 - 16/10/20
Jenson
Mirror
876/9109

Safety
Important - Please read these instructions fully before starting assembly
• WARNING: To prevent
possible overbalancing this unit
must be secured to a wall using
the 2 overbalance protector kits
supplied.
• A unit that is allowed to topple
can cause serious or fatal injury.
In addition to wall fixing the unit,
place heavy items on the lower
shelves, do not put any heavy
objects on top of the unit and
never allow children to climb or
hang on drawers, doors or
shelves.
• Refer to guide after section 22
for wall fixing information.
Care Advice
• Check you have all the
components and tools listed on
relevant pages.
• Remove all fittings from the
specified plastic bag and
separate them into their groups.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Assembly videos are
available throughout
these instructions by
scanning in the QR
codes.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean with a damp cloth.
• Warning: This unit weighs
approximately 40kgs.
Please lift with care.
• Assembly to be carried out by
a competent adult only.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Installation shall only be
carried out exactly according to
the manufacturer’s instructions -
otherwise a safety risk can
occur if incorrectly installed.
• Do not use this item if any
components are missing or
damaged.
• Regularly check all fastenings
to ensure they are properly
tightened.

Cabinet Panels Please remove protective film from any gloss panels
1 2855 x 22.8cm 855 x 22.8cm 3855 x 22.8cm
4119.9 x 23cm
657.15 x 5.8cm
556.65 x 35.5cm
755.9 x 14cm
855.9 x 6.5cm
959.4 x 37.4cm
10 59.4 x 46.2cm
DF-00023093
DF-00023094 DF-00023099
DF-00023091
DF-00023092
x 10
DF-00022254
x 4
DF-00022255
x 4
XDF-00022286
x 2
XDF-00022247
x 2
DF-00023834
x 4

Fittings Use these drawings to
correctly identify the fittings
Tools
Only used for
drilling walls
Bag 1
A
F901
F22
Ax 26 Cx 23
G
F646
x 6
Fx 8
F137
DB x 26
F900
F277
x 34
F276
x 8
E
Bag 2
H
F52
x 32 Ix 32
F63
F474
Jx 2

Fittings
Kx 4
Mx 8 Nx 8 Ox 8
Lx 4
FSTJB
FSTJC
FSTJD
FSTJE
FSTJA
Shoe Boy Kit
Tools
Only used for
drilling walls

1
2
Finished
front edge
Finished
front edge
Nx 4
1
2
1
2
Cx 2
IMPORTANT:
Panel 1 and Panel 2 have
drillings on only 1 face

3
4
5
Bx 4
1
2
1
2
Ax 10
IMPORTANT:
Panel 3 is 22mm thick
with through-holes
3
Cx 1
Bx 2
x 5
A
Finished
front edge

6
3
Nx 2
7
9
8
Nx 2
3
3
3
Finished
front edge
Cx 10
Bx 10 x 5
6
Finished
front edge
Ax 5

10
11
1
Finished
front edge
6
6
6
Finished
front edge
6
6
Finished
front edge
Finished
front edge
x 2
6
6
6
6
6
x 3
IMPORTANT:
Support panels until the
divider panel is fitted in
the next step

12
13
Finished
front edge
x 2
x 3
3
Cx 10
Bx 10
x 5
6
Finished
front edge

14
15
IMPORTANT:
Support panels until the
end panel is fitted in the
next step
x 2
x 3
3
66
66
6
Finished
front edge
Finished
front edge
Finished
front edge
2
Finished
front edge
x 2
x 3

16
17
Finished
front edge
Ax 6 Jx 2
Only use 1 Screw
to fit each Bracket
Finished
front edge
4
x 6
4

18
19
www.youtube.com/watch?v=FeaI6541z7o
Squaring up a Chest and fitting the Back Panel
A = B
Make sure measurement A and B
are the same before attaching back
panels
BB
A
A
x 26
D
IMPORTANT:
You will need to keep 8
nails for the next step
IMPORTANT:
DO NOT nail where
the Back panels meet
10
9
10
9

20
21
Ex 8
Dx 8
Gx 6
‘Tap’

22
Jx 2
See the next section for a guide
to wall mounting and fixings
Top
WARNING!
In order to prevent overturning
this product must be used with the
2 wall attachment devices provided
Carefully stand the unit up
and push it up against the
wall.
Loosely fit the 1st screw
through the brackets into the
top panel.
Slide the brackets against the
wall and mark the slot at the
back of the brackets for
drilling into the wall.
Swivel the brackets away
from the wall and drill the wall
using a suitable drill-bit and fit
your wall fixings (wall fixings
are not supplied as they will
need to suit the wall type).
Swivel the brackets back and
fix them to the wall.
Fit the 2nd screw into top
panel and tighten both screws
from the kits.
Note: Take care when
drilling the wall that you do
not drill into any pipes,
wires etc.
If in doubt, consult an
expert.

Important note:
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls You can use one of the following types of wall plug if your
walls are made of brick, breeze block, concrete, stone or wood.
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
For use with plasterboard partitions or
hollow wooden doors.
For use with walls stuck with
plasterboard. The hammer fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
No.1 “General Purpose” wall plug No.3 “Cavity Fixing” wall plug No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
A Guide to Wall Mounting & Fixings
Care &
Maintenance
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.

23
24
Finished
Shaped
edge
5
x 4
Lx 4
Hx 12
Warning:
Glass! Handle
with care
x 4
8
Finished
front edge

25
26
27
x 4
8
Ix 8
Ix 8
x 4
7
Finished
front edge
x 4
7
IMPORTANT:
Support panel until the
other shoe boy is fitted
in the next step

28
29
Ix 16
x 4
R
Kx 4
Hx 12
x 4

30
Mx 8
Hx 8
R
R
R
R